This adds the files related to MQTT-SN, with an additional exlude
to separate MQTT and MQTT-SN.
Signed-off-by: René Beckmann <rene.beckmann@grandcentrix.net>
Add a page explaining the usage of the MQTT-SN library, the client
and the UDP transport, and add it to the `protocols` index page
next to MQTT.
Signed-off-by: René Beckmann <rene.beckmann@grandcentrix.net>
Validate that basic lifecycling and usage of the MQTT-SN client
work correctly by providing a mocked MQTT-SN transport. Connection
setup and state changes are tested.
Signed-off-by: René Beckmann <rene.beckmann@grandcentrix.net>
Validate that the encoding and decoding part of the MQTT-SN library
work correctly using prepared byte arrays of messages.
Signed-off-by: René Beckmann <rene.beckmann@grandcentrix.net>
This sample demonstrates the usage of the MQTT-SN library over UDP.
It connects to a gateway, publishes to the topic "/uptime" and also
subscribes to "/number".
Signed-off-by: René Beckmann <rene.beckmann@grandcentrix.net>
This commit adds an implementation of MQTT-SN v1.2.
The specification is available on oasis-open.org:
https://www.oasis-open.org/committees/download.php/66091/MQTT-SN_spec_v1.2.pdf
The following things are missing in this implementation:
- Pre-defined topic IDs
- QoS -1 - it's most useful with predefined topics
- Gateway discovery using ADVERTISE, SEARCHGW and GWINFO messages.
- Setting the will topic and message after the initial connect
- Forwarder Encapsulation
Signed-off-by: René Beckmann <rene.beckmann@grandcentrix.net>
Add a sample presenting ipc_service working with icmsg multi endpoint
backend. The sample creates multiple instances of icmsg, one of them
consisting of two endpoints.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
The icmsg backend for ipc_service has a limitation of supporting only
on endpoint. This limitation is acceptable for many IPC instances.
However, some require to use multiple endpoints sharing a single
instance. To preserve the simple and the most efficient single-instance
backend, a separated backend is introduced implementing a wrapper
around icmsg core which adds multiple endpoints support.
There are two multi-endpoint ipc_service icmsg backends: one in the
initiator role, and the other one in the follower role. In a IPC
configuration one end of communication must be in the follower role
while the other one is in the initiator. The initiator initiates
an endpoint discovery handshake to establish enpoint identifiers for
requested endpoint names. The follower responds to requests sent by
the initiator.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
icmsg library was implemented as a ipc_service backend. It is a simple
library with minimal feature set. To preserve its simplicity while
adding more features it is useful to introduce separated ipc_service
backends with added features. To reuse most of the icmsg code for the
simplest backend and other including more features, the core of icmsg
is separated from the simplest ipc_service to an icmsg module which
can be used by multiple backends.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
Using a macro instead of repeated identical code for validation
Use macro for pdu length field encoding
Signed-off-by: Erik Brockhoff <erbr@oticon.com>
The reference count, dp->sref, is never incremented for the SSP DAI as
we use the runtime PM API's to probe/remove the DAI during
resume/suspend. Therefore, use the DAI state to check if the DAI is
active in any direction before proceesing to set the config. This fixes
the IO errors seen during simultaenous playback and capture on the same
SSP.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
The mem_map test was skipped on all the phsical x86 boards when
running twister to test them. This error happens when migrating
the new ztest. Remove the incorrect platform allow to fix this
error.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
When read callbacks are used, it bypasses LwM2M engine data
handling and therefore LwM2M observation cannot work properly.
Read callbacks should be used only on special cases.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
If gcc compiler option -Werror is used the warning,
declared inside parameter list will not be visible outside of this
definition or declaration [-Werror]
is treated as error, for
sockets_internal.h:18:28: ‘struct net_context’
sockets_internal.h:19:32: ‘struct zsock_pollfd’
fdtable.h:108:17: ‘struct k_mutex’
Signed-off-by: Christoph Schnetzler <christoph.schnetzler@husqvarnagroup.com>
Instead of guarding all BT ISO data log statements with
CONFIG_BT_DEBUG_ISO_DATA, a new macro, BT_ISO_DATA_DBG, is
implemented to handle the guarding.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Guard additional debug statements in ISO that deals
with TX/RX with CONFIG_BT_DEBUG_ISO_DATA to avoid spamming
the log.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add babblesim test for bt_disable which enables bt, starts a connection,
GATT discovers, reads, writes then disables BT in a loop.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
bt_eatt_init currently registers a l2cap server, however should not
register a new one if it has already been registered - for example in
bt_enable previously.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
Init bt_workq in bt_enable so it can be safely disabled.
Cancel rpa_update work upon disable as it is no longer required.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
Add bt_pub_key_hci_disrupted function for when hci is disrupted during
a pub key hci command, to clear callbacks and BT_DEV_PUB_KEY_BUSY flag.
Call this from bt_disable for the case bt_disable disrupts the pub key
hci command.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
Reset disconnected handles as is no longer needed after disable.
Created a destroy function to clear all connection states and cancel any
deferred work.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
Reset the adv_pool in disable so that advertising can be started after
re-enabling without issue.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
In bt_att_init, bt_conn_init and bt_l2cap_init, init the fifos and
slists before use. This means that they can be used after disable
without memory leakage.
Signed-off-by: Sean Madigan <sean.madigan@nordicsemi.no>
Includes a fix for the scenario where a PHY update event
arrives at the same time as a disconnect event.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
This commit adds a workflow to periodically clean-up the stale workflow
runs that are stuck in 'queued' state.
These stale workflow runs can result from occasional GitHub webhook
delivery mishaps and may affect the CI autoscaler decision making
process.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `pthread_create()` function is not a cancellation point and
iterating over / mutating `posix_thread_pool` is not a blocking
operation, so use a spinlock for the internal `pthread_pool_lock`.
Signed-off-by: Chris Friedt <cfriedt@meta.com>
A regression was introduced in ef804d8408
when the M_CAN driver was swapped to use the generic dcache API, but
cache management was not enabled on SAM devices.
Enable cache management on SAM devices when CAN_SAM is selected.
Signed-off-by: Perry Hung <perry@genrad.com>
The SAF XEC driver for eSPI was not enabled by default so sample
code for espi was failing. This commit changes the behavior to match
current scheme of enabling the drivers based on the status of required
device tree nodes.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
@attie-argentum has been collaborating with SAM0 SoC for a few
time. He seems to have good knowledge and it is motivated to
assume more responsabilities on the project. This add
@attie-argentum as a collaborator for Microchip SAM platforms.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The ADS1x13 does not have a PGA, and will have a fixed
internal reference voltage of 2048mV. This sets the internal
referece voltage for the ads1x1x to 2048 and adjust the gain
configuration to scale.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Updates the location of the shared memory buffer to account for
memory map chains with `mps2_an521_remote`.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Updates the location of the shared memory buffer to account for
memory map chains with `mps2_an521_remote`.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
The `mps2_an521_remote` and `mps2_an521_ns` targets have the same
memory layout for code and ram, meaning that you can't use TF-M
(`mps2_an521_ns`) and the second core (`mps2_an521_remote`) at the
same time.
This commit updates the memory map of the `_ns` build targets as
follows:
- Reduces the code memory region from 1 MB to 512 KB, maintaining the
existing base memory address of `0x0010 0000`
- Maintains the existing 512 KB ram memory at `0x2810 0000`
It updates the `_remote` target as follows:
- Reserves 468 KB code memory at address `0x0038 B000`
- Reserves 512 KB ram memory at address `0x2818 0000`
This ensures that the code region for the `_remote` target doesn't
overlap with the code region used by the single flash image layout
defined upstream in TF-M, which the `_ns` target is based upon.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
The cap test was reusing another test sim_id which
causes trouble at random when tests are parallelized.
Fix it by giving it its own id.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
KconfigBasic should not be inheriting from both KconfigCheck and
ComplianceTest. This was a workaround to find all inheritors of
ComplianceTest, so fix the inheritors search instead.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of arbitrarily storing the string provided by the caller in
either the message attribute or the element text, let the reporter
choose instead.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of accumulating failure information in a single Result instance,
located at index 0, generate one Result sub-class instance per
failure/error/skip as it is intended in the original library.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The junitparser Python module now comes with a setter and getter for
Result.text, use them instead of peeking into the underlying XML.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
