Fix Twister to generate platform reports (`--platform-reports`)
only once for each platform instead of repeating it multiple times
for each instance executed.
Signed-off-by: Dmitrii Golovanov <dmitrii.golovanov@intel.com>
Add documentation page for HTTP server functionality.
Rename existing HTTP documentation to HTTP client, as it only covers the
client library.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add missing doxygen groups for HTTP service and server APIs.
Improve doxygen API documentation when missing.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
JSON support was dropped in the initial server implementation, so remove
a leftover struct representing it.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
TLS socket have now been in Zephyr for a few years already and are
widely adopted across the codebase. Given above, they should no longer
be considered an experimental feature.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Commit 149df6b61b ("soc: nordic: nrf54h20: Disable USBHS core cache")
inadvertedly removed default MPU regions defined in arm_mpu_regions.c.
Without the SRAM_0 region defined all builds with asserts enabled result
in failed assertion even before the kernel inits. The failed assertion
is the very last step of arch_kernel_init() when MPU areas are marked
for dynamic regions. Because the failure occurs so early, the device
appears completely dead.
Fix the issue by bringing the default regions to nrf54h20 custom
regions file.
Signed-off-by: Tomasz Moń <tomasz.mon@nordicsemi.no>
Make `bt_hci_cmd_send_sync` return `-EACCES` when receiving
`BT_HCI_ERR_CMD_DISALLOWED`.
Update some tests that were expecting `-EIO` when
getting `BT_HCI_ERR_CMD_DISALLOWED`.
Add a warning in `set_random_address` when getting that new error. This
is done in case someone try to set a new random address while legacy
advertising, scanning or initiating is enabled. This is illegal behavior
according to the Core Spec (see Vol 4, Part E 7.8.4).
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Derive BT_CTLR_ISO_TX_BUFFER_SIZE from BT_ISO_TX_MTU to have
optimal Controller memory allocations.
BT_CTLR_ISO_TX_BUFFER_SIZE can be set lower than
BT_ISO_TX_MTU in which case upper layer can send fragmented
SDU to the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Rename struct bt_hci_iso_data_hdr to bt_hci_iso_sdu_hdr, and
struct bt_hci_iso_ts_data_hdr to bt_hci_iso_sdu_ts_hdr.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit adds flash controller instance for Ambiq Apollo3 Blue SOC
and Apollo3 Blue Plus SOC.
Also create the partitions on this flash controller node for apollo3_evb
and apollo3p_evb.
Signed-off-by: Aaron Ye <aye@ambiq.com>
This commit adapts the Ambiq flash controller to support the Apollo3
SOC (e.g. Apollo3 Blue, Apollo3 Blue Plus).
Also uses the Zephyr common IRQ API to replace the Ambiq HAL ones.
Signed-off-by: Aaron Ye <aye@ambiq.com>
The `cpu.h` is meant to be a hack around Zephyr's dependencies
for unit-test, relocate it to a folder that's included only by
unit-test.
Signed-off-by: Yong Cong Sin <ycsin@meta.com>
Bug in "enable/disable" argument parsing would cause
the oppostive of the requested setting to get
passed to active discharge API invocation.
Signed-off-by: Mike J. Chen <mjchen@google.com>
Fix SD card pinctrl setup for the VMU RT1170 board. The following
changes were made:
- use the "cd-gpios" property over detecting the card using the
USDHC card detect register. This should be more reliable.
- bias the clk pin high. This matches setup for the RT1170 EVK SD
pinctrl.
- remove the drive strength setting for SD pins to align with the
pinctrl settings for low speed SD mode (50 MHz) on the RT1170 EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In ull_disable, it is imperative that the callback is set up before a
second reference counter check, otherwise it may happen that an LLL done
event has already passed when the disable callback and semaphore is
assigned.
This causes the HCI thread to wait until timeout and assert after
ull_ticker_stop_with_mark.
For certain compilers, due to compiler optimizations, it can be seen
from the assembler code that the callback is assigned after the second
reference counter check.
By adding memory barriers, the code correctly reorders code to the
expected sequence.
Signed-off-by: Morten Priess <mtpr@oticon.com>
According to the RFC, MODE_IS_INCLUDE/MODE_IS_EXCLUDE codes should be
used while sendling Multicast Listener Reports in response to a query.
When performing a transition between states (e.g., when joining or
leaving a multicast group) CHANGE_TO_INCLUDE_MODE/CHANGE_TO_EXCLUDE_MODE
have to be used.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
From RFC:
* "source list" is an unordered list of zero or more unicast
addresses from which multicast reception is desired or not desired [...]
It means that there is no need to add any special address to specify
"block all" and "allow all" states explicitly. This commit removes the
unnecessary addition.
Signed-off-by: Konrad Derda <konrad.derda@nordicsemi.no>
`rtio_sqe_prep_write()` and `rtio_sqe_prep_read()` memset the sqe
struct to zeroes, clearing any configuration previously set. This
commit changes this sequence in the test, such that the sqe's are
prepared, then additional flags/configs applied.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
I got some feedback about confusion as to why the bt_addr types are not
packed. This commit adds a note about it.
This commit also adds a check for the alignof of the structs to verify
the statement 'their members are bytes or byte arrays' to thoroughly
prove that the struct is effectively as-if packed.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Disable the branch coverage calculations on the `LOG_*` family of macros.
Branch misses are due to the implementation of `Z_LOG2` and cannot be
reasonably covered in library code. The internal paths through the
`Z_LOG2` macro are not of interest when inspecting files that happen to
use the Zephyr logging API.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Moves a non-SoC Kconfig to the normal Kconfig file, as this symbol
has nothing to do with the SoC selection itself
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Modified readme for grow_r502a sample w.r.t
latest changes on driver like attributes and
LED controlling via zephyr LED subsystem APIs.
Signed-off-by: Dinesh Kumar K <dinesh@linumiz.com>
Add RX packet validator where header, address, pid
and checksum bytes are verified and validated on
every functions.
Signed-off-by: Dinesh Kumar K <dinesh@linumiz.com>
1. Add functionality for upload and download fingerprint
template data of the R502A fingerprint sensor device.
2. change data type for data_len parameter of
transceive_packet function to uint16_t as it may hold
value 256 for dowload template data to sensor.
Signed-off-by: Dinesh Kumar K <dinesh@linumiz.com>
improvised uart tx and rx handler functions to handle
large chunk of fingerprint data from/to the sensor.
Signed-off-by: Dinesh Kumar K <dinesh@linumiz.com>
Removed fps_enroll, fps_search and fps_delete from
driver code, since they did application usage inside
driver. add the following attributes to achieve the
above functionality from application.
1. SENSOR_ATTR_R502A_CAPTURE
2. SENSOR_ATTR_R502A_TEMPLATE_CREATE
3. SENSOR_ATTR_R502A_RECORD_ADD
4. SENSOR_ATTR_R502A_RECORD_LOAD
5. SENSOR_ATTR_R502A_COMPARE
Signed-off-by: Dinesh Kumar K <dinesh@linumiz.com>
return -ENOENT; when no record found on getting
attribute SENSOR_ATTR_R502A_FIND and fix array indexing
for tx data in fps_search.
Signed-off-by: Dinesh Kumar K <dinesh@linumiz.com>
Add `CHECK_DT_REG()` entries for a few additional peripheral types:
BELLBOARD, CCM, GRTC, HSFLL, UICR, and VPR.
For peripheral instances outside of the Global Domain, such as DPPIC020,
use domain-specific defines like NRF_RADIOCORE_DPPIC020 when validating.
These are always defined by the MDK, while NRF_DPPIC020 isn't guaranteed
to exist in those cases. Revise existing macro checks accordingly.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
If no HSFLL needs trimming, then `trim_hsfll()` should be compiled out.
This makes it easier to reuse the rest of `soc.c` out of tree.
Furthermore, some HSFLL instances can be trimmed before booting Zephyr,
so the FICR client properties in the DT binding should not be required.
Signed-off-by: Grzegorz Swiderski <grzegorz.swiderski@nordicsemi.no>
Only show the tmp112 runtime options when the tmp112 driver is enabled,
otherwise the option is confusing and does not appear hierarchically in
menuconfig.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
