Pending bit gets cleared by writing 1 into it, so don't use the previous
value and just write the line bit offset instead.
Change-Id: I4c88016bf53327b2670a144d3b994945f26fc002
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>¬
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Since dd5e90ec the device_get_binding call returns NULL unless the
driver_api is set by the driver. Since the exti driver only uses an
internal struct to store the callbacks, remove the need for the device
binding call from other drivers (e.g. gpio).
Change-Id: If0b733c27754108118d87ef02640311f0535ab57
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
The field is "NF: Noise detect flag". Given that every other field name is
faithful to the manual, do the same for NF.
Change-Id: I300663e6d5016bf28071d2a1926ec73682ae3d01
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
When running sanity with asserts turned on the following tests don't
fit the ROM region of CONFIG_SOC_QUARK_D2000:
- test_build_sensor_triggers
- test_build_sensors
Added filters prevent these test from being executed when asserts are
on.
Jira: ZEP-1063
Change-Id: Ib046bcb227f4a49b524894aa5aea80debe159aae
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
In QMSI 1.2 API, the RTC divider value for the prescaler can now be set
on runtime. This is done through a config parameter for the qm_rtc
driver.
Fix the rtc shim driver by using the value defined in rtc.h as
RTC_DIVIDER.
Change-Id: I5ab61a5a1a3debca103f2782e0ac584938dc91e1
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Update the QMSI drop we maintain in Zephyr, and fix the build where
needed:
- QM_USB_BASE is renamed to QM_USB_0_BASE;
- parameter int_en from qm_uart cfg struct was removed;
- driver's folder now has a new structure, fix makefiles accordingly;
- QM_WDT_MODE and related renamed to QM_WDT_CR_RMOD;
- QM_SCSS_AON renamed to QM_AONC.
Change-Id: Iffe9c66b7a3f2fe64418326e20ff0894149b3044
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
The hexiwear board has a k64 SoC, so we can reuse the k64 pinmux driver
and just add a new pinmux table for the board.
Jira: ZEP-716
Change-Id: I936691b3578db298014f44fe18433d7943b431f3
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear board pairs two Kinetis SoCs - k64 and kw40. The k64
already has SoC support in Zephyr, therefore we are adding support for
another board for the same SoC. Note, however, that hexiwear uses a
different SoC package than the Freedom board and therefore has a
different part number and pinout.
The second SoC on the hexiwear board, kw40, runs a BLE controller stack
with HCI; it does not run Zephyr (yet).
Jira: ZEP-716
Change-Id: I206f6ef58010d13075a00432040894392117e3ce
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The k64 pinmux driver can be used for any k64 board, not just frdm_k64f,
therefore renaming the driver accordingly.
Change-Id: I45e96d4a5ff6aa859d0f57fe098e44a8ae5283d1
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
For the EM Starterkit, one SOC I will soon be adding is EM7D.
This SOC has FIRQ, but only has one register bank.
Thus the interrupt handling for FIRQ needs to be different
when CONFIG_RGF_NUM_BANKS==1. The handler must instead push
registers onto the stack in the same stack frame layout that RIRQ uses.
This allows for context switch to be easily done since its compatible.
The common interrupt entry point _isr_enter must save r0 before using
it, because in the FIRQ 1-bank case, it would be destroyed otherwise.
So a global variable named saved_r0 has been added for this reason.
The stack cannot be used to save r0, because it first has to determine
whether its FIRQ or RIRQ here. This change has been tested on the
EM Starterkit with EM7D SOC changes -- coming soon. To make the review
easier, these 3 files are submitted first.
Also, exceptions will no longer use the _firq_stack.
This stack is not needed in the 1-bank case, but an exception stack
is needed. I've added a new stack called _exception_stack,
and made it be 512B, which should be enough for one exception.
See ZEP-966
Change-Id: I6f228b840da7c4db440dd1cfef4ae25336c87f0d
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Those options are not being used anywhere, so remove them and avoid some
confusion.
Change-Id: Ia3767dbd2432851dfae4b1e996f02ed1b2450505
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The Atmel SAM3 serial driver poll in function checked
for new characters incorrectly.
Change-Id: I9024a991404bf949226634c9f6c6ea507577cff1
Signed-off-by: Justin Watson <jwatson5@gmail.com>
- Renames to K_MEM_POOL_DEFINE() for consistency
- Adds alignment parameter to align the pool buffer.
Jira: ZEP-926
Change-Id: I6cf0a1ce45c3a0fc5f0675047d8928659df1e75e
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This application now executes successfully.
Change-Id: Ib3c2673fd7e8f0ff001a8355b4f7c8ddd808da94
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Now invokes any microkernel-level init functions used by
legacy applications.
Change-Id: I8f68ddba764f13d037a679b74121713983f4aaba
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
This testcase was being ran on Quark D2000 because it failed to
identify itself as micro. There is not enough RAM for that.
Properly tag.
Change-Id: I9fd4235f4436b914b89b10616cbed0cfb3e97b40
Jira: ZEP-1014
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Bluetooth controller implementation requires the low power
oscillator for radio time space scheduling and as sleep
clock; the high frequency oscillator as the active clock.
For Nordic Semiconductor's nRF5 Series SoC's select the
NRF Clock peripheral when BLUETOOTH_CONTROLLER is selected
in Kconfig build.
Jira: ZEP-897
Change-id: I6f99e90b3485e757be61e91c749e485dd0cfdaba
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
In the Nordic Semiconductor's nRF5x series SoC clock control
system can source the system clocks from a range of internal or
external high and low frequency oscillators and distribute them
to modules based upon a module’s individual requirements.
In this commit the implementation adds support for 16MHz
peripheral clock, 32.768 kHz RC oscillator, and 32.768 kHz
crystal oscillator clock sources.
16MHz peripheral clock is required to use the 2.4GHz Radio
peripheral. 32.768 kHz RC or crystal oscillator clock source
is required to use the real time counter peripheral.
Jira: ZEP-896
Change-id: I1a1e22322a5a26b587f3e27bb979e6296987ac1c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
When the debug option is enabled ECC DSA test doesn't have enough stack
space so qemu fails. Adding double stack size for special case of qemu
and CONFIG_DEBUG.
Jira: ZEP-1066
Change-Id: Ib14d853de2b1c755a6171787845433648d61b75b
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Some of tests/drivers/build_all/ test are failing link step only
when debug is enabled, these filters prevent those tests from being
executed under such configuration.
Jira: ZEP-1063
Change-Id: Ib2ff649794a1d73b133fbf998bbe8143a822c753
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Some of tests/crypto/test_ecc_dsa test are failing link step only
when debug is enabled, these filters prevent those tests from being
executed under such configuration.
Jira: ZEP-1063
Change-Id: I4b7376c49a401e21c413427918be549934ce03d5
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
Some of tests/bluetooth test are failing link step only when debug
is enabled, these filters prevent those tests from being executed
under such configuration.
Jira: ZEP-1063
Change-Id: I87fa73710d78346b1b2ce587e9055b0732d9cb49
Signed-off-by: Genaro Saucedo Tejada <genaro.saucedo.tejada@intel.com>
