Fix Kconfig help sections and add spacing to be consistent across all
Kconfig file. In a previous run we missed a few.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Driver is 'Busy' can be a warning message which can be enabled with
minimum debug level CONFIG_SYS_LOG_IEEE802154_DRIVER_LEVEL=2.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
CC1200 is a sub-ghz chip supporting 6 ISM & SRD bands: 169, 433, 470,
868, 915 and 920 MHz, with features dedicated to IEEE 802.15.4(g).
Current driver enables CC1200 against actual IEEE 802.15.4 Soft-MAC. 'g'
version support in the Soft-MAC will follow later.
The chip itself is closer to a bare metal radio modem than to a usual
15.4 chip: up to the user to provide the right RF settings for the
carrier band. Such settings can be generaten through TI's SmartRF tool.
Hopefully, for channel selection, this driver will be clever enough to
compute the proper register change without any special input from the
user. This will work for all the bands supported by the chip.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Old reference on driver's specific raw mode was still lurking around.
Removing those.
Fixes#5270
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
A very old reference to former net stack was still lurking around.
Removing it.
Taking the opportunity to clear up dependencies.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This fixes a regression from
https://github.com/zephyrproject-rtos/zephyr/pull/5018
The ieee802154 driver wouldn't build because nrf drivers/ieee802154
depends on the nordic ext drivers to build.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The interrupt priority on KW41Z is from 0..3. The value of 0x80 is
invalid, so lets set it to 0 for now as all the other interrupt
priorities default to 0 right now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added conditionally enabled event state tracing support.
Needed for enhanced debug visibility of tight timed events where
normal print debug messages affect the timing of things. This is a
simple buffer that allows post analysis via gdb of what sequencer
events occurred.
Signed-off-by: David Leach <david.leach@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Removed some debug output and changed the level of others to reduce
the amount of information logged. The reason is that some of this is
causing false positive distractions.
- Removed enabling of FILTER error IRQ events. It isn't needed and is
only informational.
- Changed frame control AR bit inspection to use native retrieval
routine.
- Addressed some coding style issues.
Signed-off-by: David Leach <david.leach@nxp.com>
Changed the logic to reset the sequencer when a RX filter
failure has been detected. This also disables the RX timer
until the next watermark detection.
Signed-off-by: David Leach <david.leach@nxp.com>
- Reworked the driver logic around TX/RX to correctly handle the
expectations of the underlying 802.15.4 hardware IP.
- Fixed a problem with TX always reporting an error to the stack
which resulted in constant retries.
- Fixed bug in RX to TX transition which would occasionally cause the
driver to error the TX.
- Changed RX logic to ensure that invalid RX frames were not passed up
the stack.
- Simplified hardware timer usage to only use TMR3.
- Added RX watermark and TMR3 support to fix a hardware problem where
the hw IP can get stuck on a receive in noisy environments.
- Modified samples/net/echo_client and echo_server kw41z project config
files to provide enanced debug visibility into stacks and threads.
Signed-off-by: David Leach <david.leach@nxp.com>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Some "random" drivers are not drivers at all: they just implement the
function `sys_rand32_get()`. Move those to a random subsystem in
preparation for a reorganization.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Waiting for tx to complete should timeout after 10ms
instead of blocking forever in case ack is not received.
Signed-off-by: Kamil Sroka <kamil.sroka@nordicsemi.no>
Issue a error message, if the _mcr20a_read_reg fails.
Do not execute SPI burst read/write if the buffer is too small.
Unlock mutex if set_pan_id, set_short_addr or set_ieee_addr
fail.
Force abort of the sequence when the higher level changes the channel
even though a T or TR sequence is in progress.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
No need to send FCS bytes as the monitor_15_4 is configured to not
expect them. If we change the monitor_15_4 to use them, then we would
need to put correct values into these two FCS bytes.
So cleanest solution is not to send FCS bytes at all.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
set_ieee_addr, set_short_addr and set_pan_id are now unused by L2, so
removing their exposure through the radio API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Further support will need work per-driver basis, as soon as the L2 will
be able to make usage of such support.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
802.15.4 is the networking hardware available in KW41Z SoC (and
supported by Zephyr). So, if networking in enabled, automatically
select the corresponding driver. This is similar to how frdm_k64f
automatically selects Ethernet driver, 96b_carbon selects BLE/IPSP
drivers, etc. (But we apply it on SoC level to reuse across the
boards.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The stack address was incorrectly specified when stack usage
was being debugged. This caused compiler to emit this warning
drivers/ieee802154/ieee802154_cc2520.c:1136:16: warning:
dereferencing type-punned pointer will break strict-aliasing
rules [-Wstrict-aliasing]
((struct cc2520_context *)(&__device_cc2520))->
^
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This patch allows the use of the MCR20A driver with KW2xD devices.
The clock output of the transceiver can be used as an input clock
for the PLL of the SoC. The hardware reset and CLK_OUT setup of
the transceiver should then be performed during the initialization
of the SoC. The driver is not allowed to do it again.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some patches have been lost during rebase before the initial commit,
this path fixes it.
- correct copyright in registers definition header file
- fix undefined macro inside CLK_OUT configuration
- use the return value of k_sem_take if there is a timeout
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add support for KW40Z in the KW41Z IEEE 802.15.4 driver as both chips
expose almost the same radio registers.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The chip seems to require a wait time before reading packet
data after the RX sequence done interrupt, as imidiate reading
of it will indicate a packet size of zero and cause the RX
sequence done to be continually retriggered.
In addition, the extra clearing of the interrupt flags can be
removed, as this is already done at the beginning of the isr.
Jira: ZEP-2278
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
There is no need to unmask/mask the global transceiver interrupt
in kw41z_start/stop as the radio interrupt line is enabled/disabled
anyway with irq_enable/disable calls.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
- set state to IDLE if TMR1 expires, but CCA reports channel as free
- no need to check for CCABFRTX, as the hardware isn't setup to do
CCA before TX
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Sequence timeouts should be scaled to 16us, as TMR_PRESCALE was set
to 62.5kHz.
Also, radio warmup times and TX packet length need to be taken into
account.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
