Fix sys log compilation warnings by defining the
SYS_LOG_LEVEL to SYS_LOG_I2C_LEVEL in Nios-II i2c driver.
This commit fixes Issue #6062
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Add I2C Master driver for Nios-II I2C soft IP core.
This driver relies upon the Altera HAL I2C driver for all the bus level
transactions, interrupt handling and register programming.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
to_read is the minimum value between I2C_ESP32_BUFFER_SIZE
and (msg.len - 1) rather than the maximum value.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
When I2C Master writes to slave on CMD_Controller, opcode WRITE
was set twice instead of 1 WRITE at the beginning of the
transmission.
And when Master reads from slave, on CMD_Controller,
byte_num = 1 + data_lenght instead of byte_num = 1 at the
beginning of the transmission.
Note that is for 7 bits addresses, to 10 bit adressess is added
more 1 in byte_num as can be seen in the code above this fix.
Signed-off-by: Vitor Massaru Iha <vitor@massaru.org>
CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Use "select USE_STM32_LL_I2C" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Wrong buffer assigned for receiving the last 2 bytes in multi
byte reception of STM32F4 i2c driver. Change the buffer to
correct one.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
According to STM32F4 reference manual, software should wait for BTF=1
before reading N-2 data byte.
Reference:
"For N >2 -byte reception, from N-2 data reception" section, page
853 of STM32F4 Reference manual.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We can have a spurious error while performing a transfer using IRQ. This
happens when the last message of the transfer is a read with a STOP
condition. We must disable the RX interrupt while waiting for the STOP
interrupt, otherwise we will get a spurious RX interrupt which will lead
to an error.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Waiting for transfer complete and stop condition uses while loops
even when interrupt mode is enabled.
Implement use of TC, TCR and STOP interrupt for interrupt mode.
msg_done is not needed in interrupt mode anymore, so move it
to non-interrupt section
Tested with stm32f3_disco board.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Disabling of Interrupts is duplicated. Move it to a position
that is common to messages that end with and without errors.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Rename the Atmel SAM I2C driver based on TWIHS module to match the
convention:
<driver class>_<SoC family>_<hardware module used by the driver>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Various minor changes to the Atmel SAM (TWIHS) driver
- clean up variable names, comments
- refactor i2c_clk_set function
- do not save configuration in dev_data
- improve ISR NACK handling
- print "Device initialized" string
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Event ISR checks if the TX/RX interrupts is enabled instead
of the TXIS/RXNE interrupt status flags. Use the TXIS/RXNE
interrupt status flags to check which interrupt event
happened.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
STM32 I2C driver doesn't use the I2C API flags STOP/RESTART,
instead it uses its own RESTART flag. As a result, I2C API's
i2c_burst_write* funtions doesn't work. This patch makes
STM32 I2C driver to use I2C API flags.
Tested on: 96b_carbon, olimexino_stm32 (i2c_ll_stm32_v1)
Tested on: stm32f3_disco, disco_l475_iot1 (i2c_ll_stm32_v2)
Fixes: #4459
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Fixes#4429
Driver didn't work properly when a transfer consisted of multiple
messages.
Fix doesn't use auto end mode anymore. msg_done function waits for
transfer to complete and issues stop condition if necessary.
Tested with stm32f3_disco board and samples/drivers/i2c_fujitsu_fram
example adapted to use I2C_1 as I2C_DEV
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
i2c actually only has two entry points into the driver,
i2c_configure and i2c_transfer. All the other APIs are derived
from these.
All derived APIs now just call i2c_transfer() with appropriate args.
The handler for i2c_transfer() needs to examine the message array
and validate all the buffers involved depending on whether we are
reading or writing to them.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This ensures DW_apb_i2c correctly transmits the slave address (7 or
10 bit) based on ic_10bitaddr_master when configured in master mode.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The ic_tar and ic_sar were earlier set to 9 bits but now its
corrected to consider 10 bits.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Atmel SAM3X series has been recently converted to use ASF and
should now use common SAM family drivers. The i2c_atmel_sam3
I2C driver will be removed in the future.
This commit also changes the default I2C driver for Arduino Due
board from i2c_atmel_sam3 to i2c_sam_twi.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
STM32F0/3 I2C's independent clock source supports only
HSI and SYSCLK, not APB1. We force I2C clock source to SYSCLK.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
IRQ_CONNECT() was being expanded with the IRQ line for the first device
twice, causing spurious IRQs.
Should fix#4398.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Supports both master and slave mode, standard and fast modes,
configurable timeouts, and a few other tunable settings.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Cleanup I2C drivers to not use bitfield access for config information
and instead use accessor macros that use shifts & masks. This is
cleanup towards removing the bitfield access in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I2C device drivers which support DTS have their default boot
configuration provided by DTS. The legacy I2C_x_DEFAULT_CFG
option in Kconfig is no longer required. This patch hides
this option from the Kconfig menu for I2C device drivers which
support DTS.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The compilation of the i2c_ll_stm32 fails when we
enable the interrupt mode. The struct i2c_stm32_data
is needed to initialize the semaphore. This patch adds
the missing struct for interrupt mode.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add _i2c_map_dt_bitrate() that maps from a bitrate to the I2C zephyr
cfg bit fields used in i2c_configure().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>