Refactor setting the maximum data length parameters supported on in
auto data length procedure. This makes setting the data length of the
connection a re-usable function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
With BT_CTLR_USER_TICKER_ID_RANGE it is possible for vendors to add a
number of ticker nodes for proprietary purposes. The feature depends on
BT_CTLR_USER_EXT.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Frame format was validated, but its length should be also validated
relevantly against the format.
Fixes#24970
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit introduces dedicated return type for custom_handler.
Relevant code is updated to fulfill the API documentation.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This exception allows USB Audio Class to properly respond to the
interface requests.
This commit is temporary solution and shall not be considered as
valid solution for other classes.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Code using this API to set a key to a value that is a string literal
produces errors in C++ because the passed pointer is not const
qualified, allowing the possibility that the callee modifies the
referenced string literal memory. Add the required const qualifiers
since the set function does not change the passed to it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
At present it is not possible to write a printf()-like function in
board code which outputs to the shell. Add shell_vfprintf() to permit
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to run tests which generate shell output and check that it
is correct. Update the existing 'dummy' backend to support this.
It works by retaining the output in a small buffer so that it can be
read and checked by the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
The numbers should have been the sum of HCI commands count and ACL TX
buffers but instead the buffer size was used which makes the pool holds
substatially more buffer than necessary.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add control over the use name option to advertise shell parameters as
an optional argument.
The argument count for extended advertise parameters had not been
updated for the maximum directed advertise parameter count.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Implement the BT_LE_ADV_OPT_USE_NAME when using bt_le_ext_adv_* APIs
to start the advertiser.
When starting an extended connectable advertiser the name must be
included in the advertising data, since scan response data is
not allowed in this configuration.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove setting state flags in bt_le_adv_start_ext since they are set
by le_ext_adv_param_set, except for BT_ADV_PERSIST flag.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Only persist advertising when the bt_le_adv_start API is used to start
the advertiser. For multiple advertising set a connectable advertiser
can only be started if there is a connection object available for the
advertiser. Leave the decision on which advertising set should be
advertising up to the application instead of suspending advertising
when no connection object is available.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Flash drivers may impose alignment requirements on the destination
buffers due to use of DMA transfers. In particular Nordic QSPI flash
API requires that addresses, sizes, and buffers all be 4-byte aligned.
Align the ready/copy buffer to satisfy this requirement.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Flash drivers may impose alignment requirements on the destination
buffers due to use of DMA transfers. In particular Nordic QSPI flash
API requires that addresses, sizes, and buffers all by 4-byte aligned.
Align the page buffer to satisfy this requirement.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This library supports stream writes to flash with
optinal progressive erase.
This module is a direct copy of the functionality found in
subsys/dfu/img_util/flash_img.c
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Convert all canbus related API/samples/tests/subsys
to the new timeout API with k_timeout_t.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Improve hexdump output of shell_hexdump() to match what is currently
printed by LOG_HEXDUMP*() family of functions. That way string buffers
that are sent/received using shell commands can be easily presented
using shell_hexdump() without loosing user experience (with previous
shell_hexdump() that printed only hex bytes) and code validity (printed
buffers are not always NULL terminated with only printable characters).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
If we have removed first net_buf, then we must not restore the
original cursor as that will point to wrong head net_buf.
Add also unit test to check that the packets are removed
properly.
Clarify the documentation that we are removing data from
beginning of the function, also document that the cursor
is reset after this call.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove the BT_LE_CONN_OPT_2M option and update documentation.
This was a misunderstand about the init PHY HCI parameter.
The init PHY in the extended connection create command does not
determine which PHYs are accepted as the initial PHY of the
connection. This is instead determined by the secondary PHY of the
extended advertiser.
The init PHY parameter only specifies which conn parameters are
provided, and since we only provide one conn parameter this option
has no effect.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Replace:
DT_FLASH_ERASE_BLOCK_SIZE ->
DT_PROP(DT_CHOSEN(zephyr_flash), erase_block_size)
DT_FLASH_WRITE_BLOCK_SIZE ->
DT_PROP(DT_CHOSEN(zephyr_flash), write_block_size)
As this allows us to phase out the old generator.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I was missing mocking api to compare data under an address pointed
by a parameter as some functions may copy buffers before passing
further.
Created ztest_expect_data and ztest_check_expected_data.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
The last parameter to hci_cmd_done() is expected to be a valid net_buf
since the function immediately tries to dereference it. Fix this by
passing the appropriate buffer reference to the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds a new flag to track if the L2CAP channel is pending waiting
for encryption to be changed to resume connecting.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for ATT_MULTIPLE_HANDLE_VALUE_NTF,
ATT_READ_MULTIPLE_VARIABLE_REQ and ATT_READ_MULTIPLE_VARIABLE_RSP.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for EATT bearer which was introduced in 5.2, they work
as extra channels to have GATT traffic, at the moment it is completely
transparent to application when they are in use since the allocation
happens automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds the definitions for Enhanced ATT along with new PDUs and UUIDs
introduced in 5.2.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a callback to indicate when the stack has released all
references to a given channel so the owner free up any resources
associated with that.
This is requires since EATT channels cannot rely on the destroy callback
as it does not use a fixed channel like ATT.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This leaves only channels on the dynamic range to be offloaded to the
system queue so ATT and EATT handling are handling in the same context.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds the initial implementation of ECRED mode which can connect up
to 5 channels simultaneously and is required by EATT.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This introduces new Enhanced Credit Based Flow Control PDUs and related
definitions which were introduced in 5.2.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Convert the usb_vbus_set function to utilize a chosen property
('zephyr,usb-device') to determine the device node that should have a
'vbus-gpios' property set for usb_vbus_set to be more than just a noop.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace DT_PHYS_RAM_ADDR and DT_RAM_SIZE with DT_REG_ADDR/DT_REG_SIZE
for the DT_CHOSEN(zephyr_sram) node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Split BT_CTLR_CONN_RSSI option into two, the base option enables the
Read RSSI command, while the new BT_CTLR_CONN_RSSI_EVENT enables the
connection RSSI events. There is no handling of RSSI events, only a
BT_INFO log.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Adding RFC1350 compliant support for TFTP Client in Zephyr. The
current implementation is minimal and only supports the ability
to get a file from the server.
Things for the future include support for putting files to
server and adding support for RFC2347.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
The bluetooth subsystem is now fully compatible with the new timeout
API, so remove the selection of the legacy API.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert bluetooth mesh to using k_timeout struct. Many of the mesh
modules uses timeout calculations, so it is most practical to keep
the s32_t type and only initialize a k_timeout_t struct when
calling the kernel.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert bluetooth host to using k_timeout_struct for the timeout values.
This is mostly replacing s32_t with k_timeout_t.
In l2cap the handling of no timeout in send channel request was removed
since the timeout is both documented as minimum of 1 second and never
given any no timeout value.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Convert bluetooth controller to using the new k_timeout_t API so that
CONFIG_LEGACY_TIMEOUT_API can be turned off.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
In order to avoid retransmissions from the peer's side
on full-close, handle states properly.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If net_pkt_pull() would cause an empty net_buf, then unref
those empty buffers from the list.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
So far socket errors reported by poll/recvfrom were ignored, which could
lead to an unexpected behavior when socket was left in an undefined
state.
Fix this, by requesting a re-registration in the LWM2M state machine,
which will close the faulty socket and open a new one. Note, that simply
closing and re-opening a socket in the lwm2m engine would not work,
since this would silently invalidate any open observations on the
lwm2m server side (due to port number change). Triggering a fresh
registration will notify the server to update its observations.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
SNTP implementation defined symbols like "MODE_MASK", which can easily
conflict with similary laxly defined symbols in other modules, and
indeed, we hit a case like that (below). So, prefix these symbols
consistently with "SNTP_", until more clear private namespacing
convention are made pervasive in Zephyr.
subsys/net/lib/sntp/sntp_pkt.h:14: error: "MODE_MASK" redefined
include/arch/arm/aarch32/cortex_a_r/cpu.h:17: note: this is the
location of the previous definition
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
On OT network with poor coverage, very often request/observe packets
doesn't get it's ACK and consumes from pendings/replies/message stacks.
In such cases when LWM2M engine tries to recover by resetting its state,
it fails because of lack of free messages.
Signed-off-by: Kiril Petrov <retfie@gmail.com>
Remove logging of individual threads spread out throughout the
bluetooth subsystem. The stacks can be analysed by enabling the
following options.
CONFIG_THREAD_ANALYZER=y
CONFIG_THREAD_ANALYZER_AUTO=y
CONFIG_THREAD_ANALYZER_RUN_UNLOCKED=y
Optional:
CONFIG_THREAD_NAME=y
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
In networks with high latencies (like NB-IoT), it's quite common to
recieve duplicated response. It's not an error condition, a correct way
to handle it is to simply ignore the duplicate. Lower the log level for
this event, not to disturb users.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The retaransmission logic was not correct in the lwm2m_engine, and could
lead to faulty behavior in case multiple messages were pending for
retransmission in the queue.
1. Since there is a singe delayed work item for entire retransmission
queue, `coap_pending_next_to_expire` should be called before
scheduling next timeout, to identify which message is going to expire
next (and when). Currently, the engine always set next timeout, based
on timeout from the message being currently re-transmitted.
2. In case the message was re-transmitted several times, and is removed
from the retansmission queue due to a timeout, next retransmission
should be scheduled, in case there are other messages on the queue.
3. Verify the timeout of the earliest message to expire in the
retransmission handler. In case messages from the beginning of the
queue were removed, we might need to schedule the retransmission
again, instead of sending message rightaway.
4. `lwm2m_send_message` is not handling retransmissions anyway, so
there's no need to check send attempts. Instead, verify
retransmission work item is already pending, and update its timeout
if needed.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
So far, coap_pending structure kept track only of the timeout interval
between two consecutive retransmissions. Calculations inside
`coap_pending_next_to_expire` relied only on this value. This approach
gives incorrect results though, in case multiple messages are pending
for retransmission.
For instance, assuming initial retransmission timeout is set to 2
seconds. If some message had been retransmitted already, its timeout
would be increased to 4 seconds. Any new message added to the pending
list would have a retransmission timeout set to 2 seconds, and will be
returned as a first message to expire, no matter how long the initial
message was already on the list.
To resolve this, add a `t0` field to the coap_pending structure. This
field is initialized to the initial transmission time, and is increased
on each retransmission by the retransmission timeout.
`coap_pending_next_to_expire` uses this value to calculate absolute
time, when the next retransmission should take place, and based on this
information returns correctly first pending message to expire.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the Kconfig `FLOAT` symbol to `FPU`, since this
symbol only indicates that the hardware Floating Point Unit (FPU) is
used and does not imply and/or indicate the general availability of
toolchain-level floating point support (i.e. this symbol is not
selected when building for an FPU-less platform that supports floating
point operations through the toolchain-provided software floating point
library).
Moreover, given that the symbol that indicates the availability of FPU
is named `CPU_HAS_FPU`, it only makes sense to use "FPU" in the name of
the symbol that enables the FPU.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Include the RPA addresses in the enhanced connection complete debug
log. This makes it easier to debug privacy failures.
Use a new debug statement so that the debug print will work correctly
when log_strdup does not copy the string.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix local RPA field for the legacy controller. This failed without
compilation errors because of blind pointer cast between two
structs of similar definition.
Set the local RPA field of the enhanced connection complete event only
when the address was generated by the controller. If the host has
set an RPA and this one was used the controller should return all
zeroes.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Set the local RPA field of the enhanced connection complete event only
when the address was generated by the controller. If the host has
set an RPA and this one was used the controller should return all
zeroes.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation issue for extended advertising beacon. Adv pool was
mistakenly put under BT_OBSERVER define.
Both observer and broadcaster use the bt_lookup_id_addr. SMP cannot
be enabled without connections, so for broadcaster and observer there
will not be a lookup.
Fix compilation warning for extended scanner-only build.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
According to the BT Core spec. The local RPA field in the enhanced
connection complete event should be set if the own-address type was
set to 0x02/0x03 and the controller generated an RPA using a non-zero
IRK, otherwise the controller should return all zeroes.
In the case where we generate the RPA in the host instead we need to
handle set the on-air RPA address based on the random address set by
the host.
If this is not handled then pairing will fail because the on-air
addresses are used as input to the pairing procedure.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Remove handling of extended advertising from connection complete
event. If extended advertising has been enabled and is supported by
the controller then enhanced connection complete must be supported.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use a smaller ordinal type than int to hold the global index
identifying devices that support power management.
Use an upper bound instead of an array of flags to identify the
devices that were successfully suspended.
Only attempt pm on devices that provide a non-default pm control
function.
Use shorter more descriptive names for state variables.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Font capabilities currently indicate whether font data is packed
horizontally or vertically, and this is used to control frame buffer
updates. The font bit ordering should likewise be recorded in the font
description, and any reversal to match the display applied when text is
being set in the frame buffer.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This is a rework for OpenISA SW LL of
"b7220cef86 Bluetooth: controller: split: Fix densely scheduled event
preemption"
Fix LLL implementation handling preemption of currently
active radio event with densely scheduled events in the
pipeline.
Preempt timeout was stopped without consideration to there
being more queued events in the pipeline. Also, added
chaining of preemption timeouts one after the other expiry
so as to preempt currently active events by the densely
scheduled events in the pipeline.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This is a rework for OpenISA SW LL of
"b0826a7f65 Bluetooth: controller: split: Reduce time to setup tIFS
switch"
Refactor to reduce the setup next tIFS switch within tIFS
period of the Radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This is a rework for OpenISA SW LL of
"4547bfb452 Bluetooth: controller: split: handle latency for cancelled
conn events" as well as subsequent fixes
Update implementation of master and slave LLL's to correctly
handle event counter values when latencies introduced due to
connection events cancelled by active events operating in
unreserved time space.
When an active radio event extends into unreserved time
space, and a connection event prepare is scheduled but at
the time of pre-emption timeout if the connection event is
cancelled then the event count and latencies needs to be
continiued to get acummulated.
In the current controller usecases the above scenarios does
not get exercised, the changes in this commit is needed for
future roles that can extend into unreserved time space and
would cancel a scheduled connection event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
This is a rework for OpenISA SW LL of
"62c1e1a52b Bluetooth: controller: split: Fix assert on invalid packet
sequence"
Fix to remove assertion failure check on detecting invalid
packet sequence used by peer central and that no non-empty
packet was transmitted.
Fixes#22967.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
User of bt_buf_get_rx may attempt to push their own headers, e.g. ACL
headers, so move the H4 header logic to bt_recv after logging into the
monitor since otherwise the buffer would contain H4 headers which is
not expected by the monitor.
Fixes#24646
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to fix the line tracking of the TCP packet allocation
with the test protocol enabled, refactor tcp_pkt_alloc(),
so the line of the allocation can be tracked properly.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
According Mesh Profile 1.0.1. A application key shall
binding single network key. And Device key shall bind all
network key, and dev key only known by cfg_cli and node self,
only used by cfg_cli & cfg_srv.
Fixes: #21088
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Fixes bug where the config client's net_key_status handler would attempt
to pull two key indexes from a message which only holds one.
Fixes#24601.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The LwM2M stack would previously ignore all OPAQUE resources when
reading them. This meant that it was impossible to read them, even if
there was a custom read callback.
Signed-off-by: Göran Weinholt <goran.weinholt@endian.se>
Some services like DHCHPv4 directly send raw packets to the iface.
This causes issue when the iface does not implement l2, e.g.
because it is a socket offload interface. fix that.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Make sure we only parse the received TCP options only once. Store
the options to tcp conn struct for later use.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch fixes an issue with TCP options reading. Previous approach
was accessing the options with pointers (th + 1). This does not work if
TCP options span multiple net_pkt buffer fragments. Instead net_pkt
functions must be used.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
During registration, first thing LWM2M does is trying to close a socket
indicated by sock_fd stored in its context. In case it is not
initialized to some invalid value (-1 in this case), LWM2M may close an
ambigous socket.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
After #22013, bt_le_adv_param got additional fields which were passed to
the bluetooth API uninitialized in the BT Mesh module. This
zero-initializes the entire structure in all usages to avoid passing
uninitialized data now and in the future.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
In order to avoid retransmissions from the peer's side
on active connection close, acknowledge the incoming FIN+ACK
in FIN_WAIT_1 state.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
We cannot directly use the local address in net_context when
registering the connection as it is not proper type. So create
temp address variable for that purposes.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Avoid dynamic allocations and all the issues if we run out of
memory, by placing the connection endpoint directly to TCP
connection struct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for multiple advertising set. Move the advertising state
flags to be per advertising set and loop over advertising sets instead
of looking up legacy advertiser set or handle 0.
Since it is not certain that the advertising set terminated event can
arrive directly after the connection complete event there is currently
a limitation that there can only be one local identity used by
connectable advertisers at a time. This guarantees that we know
the local identity being used in the connection complete event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Only attempt to restart the background scanner in connection complete
event when the new connection is a master role connection or the
initiator was successfully canceled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Enable enhanced connection complete when extended advertising has been
enabled. This event is mandatory if extended advertising is supported.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Bug fix and improved `payload` handling in `http_client_req`.
Changes to `http_client_req` behaviour:
If the user provides `payload_len` it is used to generate the
`Content-Length` header. This is done even if `payload_cb` is used to
provide the actual data. If no `payload_len` is specified then no
`Content-Length` is generated.
If `payload_cb` is provided it is called to send the payload data.
Otherwise `payload` is used as the payload buffer and sent. If
`payload_len` is not zero, it is used as the size of `payload`.
Otherwise `payload` is assumed to be a string and `strlen` is used to
determine its size. This is to maintain current behaviour and not break
existing samples.
Fixes#24431
Signed-off-by: Arvin Farahmand <arvinf@ip-logix.com>
This makes hci_raw to manage RX and TX buffers so its logic don't have
to be replicated on each an every driver/application, it also makes it
simpler to deal with extra headers for H:4 mode since that then can be
done at earlier at buffer allocation.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds support for registering a command extention table which is
used to match incoming commands and then pass the buffer to its
function handler.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds 2 config options which enables hci_raw to work in
H:4 mode and enable it by default automatically.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Buffer are allocated with K_FOREVER should never fail, in addition to
that asserts needs to be enabled and is not worth converting to runtime
check given the use of K_FOREVER.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Allowing to configuring the MPS different then the buffer size might
actually generate data fragmentation/reassembly so this just use
BT_BUF_RX_SIZE which is set accourding to the controller buffer size.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Allowing to configuring the MPS different then the buffer size might
actually generate data fragmentation/reassembly so this just use
BT_BUF_ACL_SIZE which is set accourding to the controller buffer size.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds USB_PID_BLE_HCI_H4_SAMPLE along with it driver which uses H4
over bulk endpoints.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When legacy advertising enable command is issues,
the BT_ADV_ADVERTISING has to be set, because this
flag is checked in many scenarios to see if the
advertising is ongoing or not.
Signed-off-by: Ahmed Shokry <ahmed.shokry@synopsys.com>
When receiving an unknown command send the unknown command response
as a command status event instead of a command complete event.
A command complete event has no status field, although by convention
all command parameters has a status field as the first parameter the
command status event seems like the more fitting option.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add option for low power node automatically subscribe
all-nodes-address to friend sub list.
Fixes: #24009
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
In tcp_endpoint_cmd() we allocate and then almost immediately
destroy the allocated endpoint. This is quite inefficient so
use a endpoint from stack in the compare.
Separate endpoint allocation from value setting so the caller
can decide how the endpoint union values are set.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Cell ID resource was not initialized properly in the Connectivity
Monitoring object, making it unusable from the application.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Give NULL pointer when ad_len or sd_len is zero, this stops the host
from setting a zero length advertise data or scan response.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix the advertise command not setting the peer address parameter to
NULL, this could turn it into a directed advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Some other part of Zephyr has similar defines (SRC)
causing build failures.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
New function allows to set from the code the root command. It is
an equivalent of calling 'select <rootcmd>' except it sets command
for all shell instances.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Assigning the allocated IPv4 endpoint as struct sockaddr
leads to the memory overwrite, assign the correct structure,
i.e. struct sockaddr_in.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
There was no way to use Openthread CoAP api in zephyr application so
far. These changes enable the feature. Now you can fully use CoAP
communication in an application working in Thread network.
Signed-off-by: Lukasz Maciejonczyk <Lukasz.Maciejonczyk@nordicsemi.no>
Set information about Frame Pending Bit from the ACK response in the
frame passed to OpenThread.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to implement active connection close with the
TIME_WAIT state, send FIN and enter FIN_WAIT_1 state.
We actually send FIN+ACK as most of the implementations do.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to support TIME_WAIT state during the TCP connection
termination, add a TIME_WAIT timer and the corresponding state.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to improve readability, rename TCP_FIN_WAIT
states into TCP_FIN_WAIT_1, TCP_FIN_WAIT_2.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of privacy on VEGA platform
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
The radio on the VEGA platform will now be able to resolve Resolvable
Private Addresses through the use of the CAUv3 hardware. With this
patch the RPA feature is now fully supported on the Controller:
RPA addresses are generated with local IRK and resolved with
previously exchanged peer IRK.
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
When disconnecting att_reset is called and all requests are notified
but instead of passing req->user_data like it should it pass the req
itself which nowdays comes from a k_mem_slab, rather than being a
contiguous memory that would contain the request and its user data,
which would likely cause invalid access.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add shell options to configure an extended advertiser for directed
advertising.
Add shell options to provide arbitrary advertising data as well as
giving scan response data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This patch introduces two major changes to the directed advertising
feature of the bluetooth host.
Deprecating the bt_conn_create_slave_le, and removing
bt_conn_le_create_slave which has never been released. This behaviour
has now been moved by to providing the peer direct address into the
advertising parameters.
Introducing directed advertising support for nonconnectable
directed extended advertising, both scannable and non-scannable.
A bug was also fixed in the the directed-adv command in the shell
when the argument "low" was given. The advertiseng parameter pointer
declared with BT_LE_ADV_CONN_DIR_LOW_DUTY was declared in a scope that
was no longer valid when it was used to start the advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Makes a common link_closed function for PB-GATT, getting rid of a bug
where cb_data is reset before the link closed callback. Also ensures
that the link close and reset order is the same in both scenarios.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the hardware identifier obtained with the hwinfo API is stored
in the correct order based on the platform, there is no longer the need
to reverse its bytes when populating the serial number in the
corresponding USB descriptor.
Fixes#24103
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The LE Connection Complete HCI event, unlike its Enhanced counterpart,
only uses 0x0 and 0x1 for Peer Address Type. Fix it so that it reflects
the specification correctly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fill the mTimestamp filed in OpenThread frame based on the net_pkt
timestamp value (only if NET_PKT_TIMESTAMP is enabled).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This change is to allow access to the firmware block context in order to
give the firmware update callback implementation an indication of when
to reset the flash context. Additionally, it allows for a validity check
between the total expected size downloaded and the actual size
downloaded. A simple implementation can check if the block context's
current downloaded blocks is equal to the expected block size in order
to determine if the flash context needs to be reset. This approach
seemed the simplest, and knowing the firmware block context can have
other purposes. This has been tested by accessing the block context
during the update in the block received callback and confirming that the
callback had information regarding the current downloaded bytes.
Fixes#16122
Signed-off-by: Kyle Sun <yaomon18@yahoo.com>
Received frames shall be handled in the OpenThread thread, not in
the receiver thread.
Passed received frame to the function that will handle it in a proper
thread instead of calling otPlatRadioReceiveDone directly.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
OpenThread received frame handling shall be done in the OpenThread
thread.
Created API to pass net packets to the proper thread and handle them
there.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
The time parameter cannot be K_NO_DELAY because the time delay
parameter is ms so using value 0 instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_context API will change, the s32_t timeout parameter
will be changed to k_timeout_t. All the Zephyr users of this API will
be changed in subsequent commits. This is internal Zephyr API only,
so the API is not deprecated etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Mention in websocket API documentation that the timeout value
is in milliseconds. Check timeout values properly using K_TIMEOUT_EQ()
macro.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use k_timeout_t internally, no change to user API.
Clarify the documentation of the timeout parameter that it is
in milliseconds.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use 64-bit time in order to avoid overlaps, and do not use K_MSEC()
as that will convert to k_timeout_t which we do not want in this
case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This PR fixes#23482. The preamble size for a 2M phy was incorrect.
There is a bug in calculation of time for the DLE procedure:
the preamble size is incorrect for the 2M phy
Fixes#23482
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
When PB-GATT Procedure timeout, func `bt_mesh_pb_gatt_close`
will also dumplicated with `link_closed()`
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Check the return value of LE Set Extended Advertising Parameters
command when starting an advertiser from bt_le_adv_start with
CONFIG_BT_EXT_ADV enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The LE Set Extended Advertising Set Random Address command may be
issued at any time after an advertising set identified by
the Advertising Handle parameter has been created using the
LE Set Extended Advertising Parameters command.
This commit fixes the advertising set issueing the set random address
command before the advertising set is created in the controller.
Since the le_adv_set_random_addr function has is used to get the the
own address parameter for the it could not simply be moved, and
moving the own address parameter handling out of this function
would create a potentioal maintaince problem.
Also this function is used for both with and without advertising
extension feature so changing it is not trivial without breaking all
the previous random address handling already put in place.
The simplest solution was therefore to postpone the command until the
parameters has been set using 2 flags.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use bluetooth assert on HCI command send error since this assertion is
always enabled and we should not continue after this has failed.
Log command status failure with information in order to make it more
visible as the HCI status code is more interesting than the -EIO error
code returned by the function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add BT_ASSERT_MSG assert mechanism that can print assertion messages
when verbose bluetooth asserts are enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix seg_tx occupy when no segment not send
and allocate rx_seg when receive such message.
Fixes: #24101
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
For the ll code we know the exact entropy device as its the one for the
SoC that we are on. So use the new DT macro's to get the entropy device
via DT_INST rather than using CONFIG_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix the pending slave set connection latency and timeout values not used
in the connection update procedure when
CONFIG_BT_GAP_PERIPHERAL_PREF_PARAMS has not been enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
OpenThread uses "tx started" notification to start ACK
timeout if the driver does not support it.
In order for this to be achieved tx task needs to run in parallel
to the OpenThread task, otherwise it may delay the gap between
cca and tx or run after transmission has already finished.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
The function calculates the number of octets put, but does not return
it. Call sites check for non-zero values suggesting this is a bug.
See https://habr.com/en/company/pvs-studio/blog/495284/ fragment 12.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the size of the target buffer as the maximum length when
formatting with snprintf.
See https://habr.com/en/company/pvs-studio/blog/495284/ fragment 3.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This patch enables handling of a single octet of option-kind at the end
of the option list (EOL). Also, add functionality to drop a segment with
an invalid single octet option-kind at the EOL.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Extends the bt_conn_le_create_param struct to provide the option
to set a custom timeout for the initiation of the connection.
The logic for the default values of window_coded and interval_coded
were moved to conn.c in order to resolve all defaults for the
create_param struct at a single location.
Timeout is not added as a parameter to the BT_CONN_LE_CREATE_PARAM
macro due to the expectation that CONFIG_BT_CREATE_CONN_TIMEOUT
will be the typical value that users will expect.
Fixes#23468
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Fixed overflow risk when `poll_timeout` is 1s,
although it is not recommended to use it like this,
when it is used like this, `POLL_TIMEOUT_MAX`
will overflow.
When the poll timeout set like above, the default `6`
req_attemps for first pull request lost,
may cause this procedure bigger than poll_timeout,
Well, stop scanning when lpn terminated friendship,
this will save lots of energy, when lpn mode enable,
the scanning will be start after `FRIEND_REQ_RETRY_TIMEOUT`
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Fix an an issue where established bonding information in the peripheral
are deleted when the central does not have the bond information.
This could be because the central has removed the bond information, or
this is in fact not the central but someone spoofing it's identity, or
an accidental RPA match.
This is a regression from: a3e89e84a8
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The net_buf subsystem is now fully compatible with the new timeout
API, so move the selection of the legacy API to those specific
subsystems that use net_buf and still need converting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch updates the net_buf API to use k_timeout_t in essentially
all places where "s32_t timeout" was previously used. For the most
part the conversion is trivial, except for the places where
intermediate decrements of remaining timeout is needed. For this the
z_timeout_end_calc() API is used.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Update implementation of master and slave LLL's to correctly
handle event counter values when latencies introduced due to
connection events cancelled by active events operating in
unreserved time space.
When an active radio event extends into unreserved time
space, and a connection event prepare is scheduled but at
the time of pre-emption timeout if the connection event is
cancelled then the event count and latencies needs to be
continiued to get acummulated.
In the current controller usecases the above scenarios does
not get exercised, the changes in this commit is needed for
future roles that can extend into unreserved time space and
would cancel a scheduled connection event.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add additional build configurations to the shell to catch build errors
when enabling extended advertising.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix compilation issue when extended advertising is enabled but privacy
is disabled. In this case the rpa_update work is compiled out.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use existing network stack calls to create net pkt,
ip header and udp header creation. Also simplify
finalize api calls.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Use existing network stack calls to create net pkt,
ip header and tcp header creation. Also simplify
finalize api calls.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
net_context local sin/sin6 addresses are used only
when input src is not available. So ASSERT should
be inside if block.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
In case hardware CSMA CA is used, ieee802154 L2 does not initialize ACK
processing structures, as it does not need to process ACK messages. As
it is not possible to conditionally disable ACK reporting to the upper
layer, ieee802154 could end up using uninitialized kernel primitive
(semaphore) in the ACK handler, which lead to a crash.
Avoid this, by explicitly checking in the ACK handler, if HW CSMA CA is
used.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Even though radio driver can report in its capabilities that it does
support CSMA CA, there's no way in the driver to select how the frame
should be transmitted (with CSMA or without). As layers above radio
driver (Thread, Zigbee) can expect that both TX modes are available, we
need to extend the API to allow either of these modes.
This commits extends the API `tx` function with an extra parameter,
`ieee802154_tx_mode`, which informs the driver how the packet should be
transmitted. Currently, the following modes are specified:
* direct (regular tx, no cca, just how it worked so far),
* CCA before transmission,
* CSMA CA before transmission,
* delayed TX,
* delayed TX with CCA
Assume that radios that reported CSMA CA capability transmit in CSMA CA
mode by default, all others will support direct mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Run the int_literal_to_timeout Coccinelle script to fix places where
it is clear that an integer duration is being passed where a timeout
value is required.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Most places used an int so that should have handled most cases but
keys_set was using an unsigned int, which meant that checking len > 0
is an expression that is always false, and the error handling is not
working.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Implemented blocking OpenThread otPlatRadioGetRssi api function using
no-blocking energy scan function from radio driver api interface.
Signed-off-by: Tomasz Konieczny <tomasz.konieczny@nordicsemi.no>
The publication context is checked for NULL in bt_mesh_model_publish()
however it was dereferenced before that. Move the assignment to
ctx.send_rel to the same place where other ctx members are set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Counting how many times it went suspended, for how long on the last one
and on overage.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
End option indicates the end of the option list. Hence, correct way to
handle it is to break out of the option parsing routine.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
k_sleep() now takes a k_timeout_t so an integer value needs to be
wrapped through the appropriate macro, in this case K_SECONDS().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Verify that `ed_scan` is implemented by the radio driver before use. In
case it's not, return appropriate error code to OpenThread.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Fix regression in cancelling slave latency during Connection
Update Procedure.
Slave latency should not be applied between the ack of a
Connection Update Indication PDU and until the instant.
When caching was introduced, implementation missed this
consideration.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Ticker is now fixed to avoid catch up of periodic timeout under
large ISR latencies.
Revert commit a749e28d98 ("Bluetooth: controller: split:
nRF: Use ticker compat mode as default").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If must_expire is set for a ticker instance, then ticker
expiry shall still perform catchup.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Reset ticker state in ticker_job for ticker instances that
have been skipped in the ticker_worker.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix ticker to avoid catch up of periodic timeouts in case of
large ISR latencies like in case of flash erase scenarios.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix regression in cancelling slave latency during Connection
Update Procedure.
Slave latency should not be applied between the ack of a
Connection Update Indication PDU and until the instant.
When caching was introduced, implementation missed this
consideration.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Simplify the Data Length Update Procedure state check when
processing incoming LENGTH_REQ/RSP PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Simplify the Data Length Update Procedure state check when
processing incoming LENGTH_REQ/RSP PDUs.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add validation of channel map and hop increment value
received in CONNECT_IND PDU.
Zero bit count leads to controller assert or divide-by-zero
fault.
Hop increment shall be between 5 and 16 by BT Specification.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add validation of channel map and hop increment value
received in CONNECT_IND PDU.
Zero bit count leads to controller assert or divide-by-zero
fault.
Hop increment shall be between 5 and 16 by BT Specification.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit makes cdc class to omit notifications about
interfaces swap that may happen if cdc is configured together
with audio.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
According to RFC 793 and IANA "TCP Option Kind Numbers" an option with
kind 0 is an End of Option List option and not a PAD.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
Add a k_timeout_t type, and use it everywhere that kernel API
functions were accepting a millisecond timeout argument. Instead of
forcing milliseconds everywhere (which are often not integrally
representable as system ticks), do the conversion to ticks at the
point where the timeout is created. This avoids an extra unit
conversion in some application code, and allows us to express the
timeout in units other than milliseconds to achieve greater precision.
The existing K_MSEC() et. al. macros now return initializers for a
k_timeout_t.
The K_NO_WAIT and K_FOREVER constants have now become k_timeout_t
values, which means they cannot be operated on as integers.
Applications which have their own APIs that need to inspect these
vs. user-provided timeouts can now use a K_TIMEOUT_EQ() predicate to
test for equality.
Timer drivers, which receive an integer tick count in ther
z_clock_set_timeout() functions, now use the integer-valued
K_TICKS_FOREVER constant instead of K_FOREVER.
For the initial release, to preserve source compatibility, a
CONFIG_LEGACY_TIMEOUT_API kconfig is provided. When true, the
k_timeout_t will remain a compatible 32 bit value that will work with
any legacy Zephyr application.
Some subsystems present timeout (or timeout-like) values to their own
users as APIs that would re-use the kernel's own constants and
conventions. These will require some minor design work to adapt to
the new scheme (in most cases just using k_timeout_t directly in their
own API), and they have not been changed in this patch, instead
selecting CONFIG_LEGACY_TIMEOUT_API via kconfig. These subsystems
include: CAN Bus, the Microbit display driver, I2S, LoRa modem
drivers, the UART Async API, Video hardware drivers, the console
subsystem, and the network buffer abstraction.
k_sleep() now takes a k_timeout_t argument, with a k_msleep() variant
provided that works identically to the original API.
Most of the changes here are just type/configuration management and
documentation, but there are logic changes in mempool, where a loop
that used a timeout numerically has been reworked using a new
z_timeout_end_calc() predicate. Also in queue.c, a (when POLL was
enabled) a similar loop was needlessly used to try to retry the
k_poll() call after a spurious failure. But k_poll() does not fail
spuriously, so the loop was removed.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The check for label property is really checking to see if a device
exists and the better way to do that is to use DT_HAS_NODE(). Replace
refernces of DT_NODE_HAS_PROP(DT_INST(...), label) with
DT_HAS_NODE(DT_INST(...)).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Minor clean up to remove unnecessary references in the code to
CONFIG_HAS_SYS_POWER_STATE_SLEEP_1 and
CONFIG_HAS_SYS_POWER_STATE_SLEEP_2, as they are always defined for this
SoC.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Use of macros such as SYS_POWER_STATE_SLEEP_2 needs to be guarded by
making sure CONFIG_SYS_POWER_SLEEP_STATES is defined.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Fix high-duty cycle directed advertising when extended advertising
feature has been enabled. The duration parameter when starting extended
high duty cycle directed advertising has to be set to a non-zero value
less than or equal to 1.28 seconds.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Avoid removing identity keys from the controller during the pairing
procedure. During the pairing procedure the keys will be cleared before
they are updated. This causes an unnecessary warning from HCI core where
it tries to remove an IRK key-set from the controller that has has not
been added yet.
While this is not an issue, the warning from HCI core is misleading and
might lead to unnecessary questions and investigations.
Warning appeared after: 6c6bd8c49e
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the pending ID keys add and delete flag out of keys storage area.
These flags are runtime flags and should not be stored in persistent
storage.
Due to struct alignment storage start has to be aligned so that
variables added before storage start does not affect the storage bytes
by introducing padding in the storage area
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Add shell advertise set info get command to print advertiser set local
identity and TX power selected by the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Skip feature testing of controller features when legacy advertising
commands are not supported. For combined builds or builds where the
capability of the controller is known it is not required to have runtime
check of controller extended advertising support.
This gives the following size reduction for hci_core.c:
Without legacy support
hci_core.c 19980 7.75%
total 257679
With legacy support
hci_core.c 21816 8.41%
total 259519
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Handle updating the identity keys in the controller while a scanner
limited by timeout or advertiser limited by number of events or timeout
is active in the controller. For this case we mark they keys as pending
and handle the update of the resolving list ones the roles are stopped.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add RPA handling for scan limited by timeout. The scan limited by
timeout has no information about elapsed time when stopped. So pausing
the scan at RPA timeout has no new scan timeout value to set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add shell command to retrieve advertising set OOB information for the
selected advertising set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add error code to API for starting directed advertiser. Also rename the
API in order to follow the established naming pattern.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add advertising sent connected and scanned callback and print the
information available.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add shell arguments to control scanning phys for scanner and initiator.
This allows to scan on coded or create connections on coded.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add scan recv callback and print extended scan information available.
Add scan timeout callback to print when scanner has stopped.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Print the error codes in hex so that it is easier to lookup, error
codes are usually given as hex.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for creating and advertising with an advertising set.
This has support to advertise with extended data and with long range
feature on Coded PHY.
Limited to only supported one advertising set.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support to use the extended conn create options to establish
connections on LE Coded PHY or 2M. This uses the connection options
set by bt_conn_set_scan_params.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add API to set the scan parameters used in the LE Create Connection
HCI command used by bt_conn_create_le and bt_conn_create_aute_le.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for the new scan options and use the LE Extended Scan
HCI commands if they are available in the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor scan and initiator random address handling to a helper function
so that it can be re-used.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add reference count old to new value transition in the debug print, this
makes it easier to interpret the printed line when debuggin reference
count bugs.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extract setting advertising filter policy parameter from the adv params
options field to a helper function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use the scan types defined in bluetooth.h instead of the hci defined
ones. Although they have the same value it is best to avoid using the
hci.h header in applications.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update buffer sizes needed when advertising extensions is enabled. Since
BT_RX_BUF_LEN is used for the HCI command as well we need to fit the
full 255 bytes of the Set Extended Advertising Data or Scan Response
Data plus the 3 byte header of an HCI command.
For the discardable buffer size we need to fit the LE Extended
Advertising Report event, which can be a maximum of 255 bytes plus the
2 byte header of an HCI event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add Kconfig options to enable extendend advertising and scanning
support.
Include option to support both types of advertising
commands in case the controller capabilities is not know or the
controller is pluggable.
Include option to only support legacy advertising API, this is to
support the use-case of advertising using different identity than the
scanner or initiator.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate BT_LE_ADV defines in hci.h that are expected to be used by the
application in the scan received callback to identify the advertising
PDU type. These defines are mixing HCI input parameters and advertising
PDU types. Internally it is acceptable to mix these, but at the API we
should to mix in them.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename filter_dup parameters used for scanning filter options to the
more generic name options, and make scan filter options follow same
naming patters as advertising and initiator scan options.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate bt_create_conn_le and rename it to in order to add return
code, new arguments and to follow the established naming convention.
Add API for the application to control the scan parameters of the
initiator role. This allows the application more scheduling control
of the initiator in multi-role scenarios. Also provides options to
configure the initiator for LE Coded PHY for long range support.
We deprecate the old way of creating connection to make the name more
consistent with the rest of the API.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Identify when received PUBLISH message is malformed and overall packet
length received is smaller than parsed variable header lenght.
Add unit test to cover this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Verify more strictly that data read from the transport fits into RX
buffer. Switch to unsigned integers, where possible, to prevent
unnecessary signed/unsigned operations.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The standard allows up to 4 bytes of packet length data, while current
implementation parsed up to 5 bytes.
Add additional unit test, which verifies that error is reported in case
of invalid packet length.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
With the introduction of ZephyrConfig.cmake all parts of CMake code
should rely on the CMake ZEPHYR_BASE variable instead of the environment
setting.
This ensures that after the first CMake invocation, then all subsequent
invocation in same build folder will use same zephyr base.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Such state needs to be set _from_ the PM API functions and not the other
way round. So if a network device driver does not support such API, it
will not be able to set the core net_if on PM state, obviously.
Currently, these functions only set/unset NET_IF_SUSPENDED flag.
More logic will be added later, to decide whether the net_if can be
actually set to suspend mode or not and also to take care of all timers
related to the interface.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This function can be used for example by network power management
to check if the network interface can be suspended or not.
If there are network packets in transmit queue, then the network
interface cannot be suspended yet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to know whether the net_pkt was successfully placed
to transmit queue. It is possible in TX side, that the net_pkt
is already in TX queue when for example TCP packet is
re-transmitted, in which case the queue submit will fail.
This cannot happen in RX side as there are no timers involved.
It is required to check about such pending flag before trying to submit
it into the queue. Indeed, the work queue could be scheduled right after
such queuing, thus checking for the pending flag afterwards would
provide a false information.
It is unfortunate k_work_submit_to_queue() does not return anything as
it would simplify the code then.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Minor optimization to use a local variable instead of a
deferencing of a struct member.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is a new init level SMP that was just added, and this module needs
to take it into account.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix so that different isochronous synchronization modes can be used.
It filters out the synchronization mode before sending the endpoint
type to drivers.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
Update the ticks_current value on last stopped ticker
instance, so that when a new ticker instance is started
the anchor ticks calculation uses the correct current tick
with respect to supplied anchor ticks.
Fixes#23805.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit renames the `cortex_r` directory under the AArch32 to
`cortex_a_r`, in preparation for the AArch32 Cortex-A support.
The rationale for this renaming is that the Cortex-A and Cortex-R share
the same base design and the difference between them, other than the
MPU vs. MMU, is minimal.
Since most of the architecture port code and configurations will be
shared between the Cortex-A and Cortex-R architectures, it is
advantageous to have them together in the same directory.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Sleep mode 1 is supposed to be a low-latency sleep mode where devices
are left in active mode. Thus we should only bring devices to low-power
when in sleep mode 2 in sys_pm_policy_low_power_devices().
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
In case OPENTHREAD_NCP option is disabled, uart.c platform driver should
not be compiled as it misses dependencies.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When NCP starts-up some of the initialisation functions of a regular
OpenThread device do not need to be called, because they get triggered
by wpantund via UART. Instead NCP initialisation needs to be called.
A small typo has been fixed as well.
Also initialisation for raw link packet interface has been added. Can be
used for picking up 802.15.4 frames and interpreting them in the
application.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
The functions ppp_mgmt_raise_carrier_on/off_event() were not
implemented, but already documeted in the header net/ppp.h
Fixes#23420
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The commit reduces default MCUMGR buffer size and introduces changes to
mcumgr that fix problem with mcumgr not being able to download file off
the Zephyr running device.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Remove use of k_cpu_idle in controller, and refactor the
implementation used to start, wait and stop clocks needed
by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix directed advertising from privacy disabled peer. In this case we
need to have the local IRK in the controllers resolving list in order to
have the controller resolve the initiator address of the directed
advertising pdu (ADV_DIR_IND).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix directed advertiser using the wrong local IRK when doing directed
advertising when the identity of the advertiser is not the default
identity.
This is only an issue for the directed advertiser because it is only
for the directed advertiser that we use the controllers local IRK
to generate the Advertisers RPA.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add header definition for bt_read_static_addr function. Declaring it
without a header definition will not give any compilation error when
function definition changes.
Refactor nRF SoC specific code into nRF specific source files and
provide weak definitions when these are not implemented. This will make
it easier to add handlers per vendor.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
To complete the removal of the ext/ folder, move the ctf_map.h file to
where it really belongs, which is subsys/tracing/ctf.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When using BT_LE_ADV_NCONN_NAME then the advertising name will not be
included in the advertising data. This is because the host always puts
the device name in the scan response. But since the scan data was
otherwise empty the advertising type was set to ADV_NONCONN_IND.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Splits PB-ADV and PB-GATT into separate modules with a common interface
to modularize prov.c.
Additional trivial fixes from testing:
- Reduces warnings for normal occurances like repeated packets.
- Makes link ack a non-reliable packet to prevent it from being repeated
until prov invite.
- Provisioner does not send link fail, but closes the link (as per spec
section 5.4.4). This prevents lingering zombie links on both sides.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Allocates segmented message buffers as slabs in a common pool for RX and
TX. This reduces memory requirements for both TX and RX, as TX messages
can be stored without the network and advertising buffer overhead, and
RX can use only the slabs it needs, instead of allocating a full size
segmented message. This approach also removes the need for decrypting
the segments for each retransmission, reducing overall processing load.
Slab based segmentation for tx also introduces queuing of segmented
messages, which allows the application layer to send multiple messages
to the same destination without violating Bluetooth Mesh specification
v1.0.1, section 3.6.4.1. This mechanism is provided through a flag that
blocks segmented messages to a destination which a message is already
being sent to until the previous message finishes.
This changes the SDU size configuration to a symmetrical
RX_SEG_MAX/TX_SEG_MAX pair of configurations, plus a new segment pool
side configuration. It also removes the binding between the TX_SEG_MAX
config and the advertising buffers, reducing the minimum advertising
buffer count from 6 to 3.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The Friend queue uses the message SeqAuth to determine whether the
message is already in the queue. To facilitate this, the SeqAuth is
passed around as a pointer throughout the transport modules. In the
bt_mesh_ctl_send functions, this parameter is also exposed in the API,
but the internal usage is inconsistent and buggy. Also, no one actually
uses this parameter.
- Removes seq_auth param from bt_mesh_ctl_send, instead passing NULL
directly to the friend module, to enforce its addition to the queue.
- Makes the seq_auth pointer const throughout the friend module.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
A bug in the PKT_US resulted in wrong calculations for the 2M phy.
Fixes the bug, verified on EBQ.
Also adds some defines for improved readability.
Fixes#23482
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
Fix LLL implementation handling preemption of currently
active radio event with densely scheduled events in the
pipeline.
Preempt timeout was stopped without consideration to there
being more queued events in the pipeline. Also, added
chaining of preemption timeouts one after the other expiry
so as to preempt currently active events by the densely
scheduled events in the pipeline.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix regression in handling invalid packet sequence in the
first packet in a connection.
This relates to commit 62c1e1a52b ("Bluetooth: controller:
split: Fix assert on invalid packet sequence")
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix regression in handling tx pool corruption in relation to
commit 7a3e29af06 ("Bluetooth: controller: legacy: Fix Tx
pool corruption").
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
ieee802154_scan() checks if ctx->scan_ctx (scan) is NULL what implies
that this can be true, but de-reference this variable before this
check what may cause a problem.
Fixes#23299 [3]
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
ftpr assignment is being done before checking fb->fonts pointer.
Just changing assignment position.
Fixes 23299 [1]
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
If the network interface is down, we should timeout properly
and let the application to handle the situation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix API usage error introduced by the commit c88155fd2d
("usb: mass_storage: fix possible page buffer overflow")'
Fixes: #23295
CID: 208676
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Fix response to unexpected LL_FEATURE_RSP for the case that
BT_CTLR_SLAVE_FEAT_REQ is disabled. Fixes LL/PAC/SLA/BV-01 for such a
configuration.
Signed-off-by: Wolfgang Puffitsch <wopu@demant.com>
It is possible that net_pkt will disappear while we are sending
it, so save link address if we need that information.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are receiving UDP packet and if there is some error happening
inside zsock_recv_dgram(), then make sure that the net_pkt received
from recv_q is freed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was leaking memory in TX side when there was lot of
incoming packets. The reason was that the net_pkt_sent() flag
was manipulated in two threads which caused races. The solution
is to move the sent flag check only to tcp.c.
Fixes#23246
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This PR provides changes that are required after replacing Tinycbor
with copy of source code from mynewt-core.
The Tinycbor has been replaced with mynewt-core version to reduce
maintenance effort; by replacing it the Zephy specific changes have been
reduced to small patch over mynewt codebase.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The set of interrupt stacks is now expressed as an array. We
also define the idle threads and their associated stacks this
way. This allows for iteration in cases where we have multiple
CPUs.
There is now a centralized declaration in kernel_internal.h.
On uniprocessor systems, z_interrupt_stacks has one element
and can be used in the same way as _interrupt_stack.
The IRQ stack for CPU 0 is now set in init.c instead of in
arch code.
The extern definition of the main thread stack is now removed,
this doesn't need to be in a header.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fixes#23485
When we create a GATT table dynamically, we also create a hash
identifying this table. This hash can be stored in persistent memory and
we can thus determine after recreating the GATT table whether the
services have changed or not from before the reboot.
When these hashes are identical, it implies that the table has not
changed, wherefore a service changed indication should not be sent to
any bonded clients. The method for achieving this was to remove the
gatt_sc.work entry from the work queue. This work queue entry was to
send an indication to the clients when the table had been allocated.
If the final entry then caused the hashes to match, the indication
would be cancelled.
On unit testing this behaviour in simulation and in practice, we found
that the indication was sent nonetheless, and the issue was located to
be tied to the SERVICE_RANGE_CHANGED flag which is set when the services
are changed and is cleared when the indications are being sent out.
It was the job of the work queue entry to clear this flag, and as the
entry was never serviced, the flag was never cleared, and when
sc_commit() is called at the end of the process, it believes that there
is a new service change pending and therefore starts the job over, thus
creating a redundant indication to the clients.
This commit fixes the issue by clearing the flag when the work entry
is removed due to a hash match. This has been unittested in a live
environment, in a simulation environment, and sanitycheck has been run
on it.
Signed-off-by: Dan Erichsen <daee@demant.com>
The device power management infrastructure maintains a hard-coded list
of critical devices to ensure suspend and resume are performed in the
proper order. PR #21298 combined the 32 KiHz and 16 MHz clock devices
into a single driver, changing the name so the clock driver is not
handled at the correct time, but rather at whatever point it appears
in the general device list.
Update the list to the current clock driver name. Also store the
device names as standard strings rather than padding them to a fixed
length.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The commit e85dd8af5d changed the way the BT_ECC Kconfig option
is enabled, however it got the dependency wrong. The dependency should
only look at BT_SMP_OOB_LEGACY_PAIR_ONLY if BT_SMP was also enable.
This broke e.g. the build of the mesh_demo app for the BBC
micro:bit since the memory consumption jumped up by roughly 2k.
This patch fixes the issue, and in the same go makes the Mesh handling
consistent by also using a conditional default rather than select.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is placeholder code; better kernel support for dumping
exception/interrupt related stacks is forthcoming.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The current design of the network-specific stack dumping APIs
is fundamentally unsafe. You cannot properly dump stack data
without information which is only available in the thread object.
In addition, this infrastructure is unnecessary. There is already
a core shell command which dumps stack information for all
active threads.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Allow to get local OOB data while advertiser, scanner or whitelist
initiator is active. If direct initiator is active or the advertiser
is using the random address as a random static identity address then
the function will return error.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
When OOB callbacks are present it is possible to achieve authenticated
pairing without having the remote OOB data present. Using OOB with
LE Secure Connection only one side of the pairing procedure is required
to have the OOB data present. If we have given the remote our OOB data
then pairing can proceed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update LLCP handling during PHY update and Data Length update to not
start the LL control procedure if the remote has already indicated that
the procedure is not supported.
This fulfills the following requirement from the BT Core Specification
(Core_v5.2, Vol 6, Part B, Section 4.6):
Except where explicitly stated elsewhere in this specification, if the
peer Link Layer has indicated either during a feature exchange procedure
or by responding with an LL_UNKNOWN_RSP PDU that it does not support a
procedure, then the Link Layer shall not use that procedure.
Re-use the connection parameter request handling for PHY and
data length update procedures.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix missing first connection event due to first connection
event ticks_slot overlapping with the initiator window
ticks_slot.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add ticker_stop_abs interface, similar functionality as to
ticker_stop interface to stop a running ticker but with a
supplied absolute tick reference value.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Contents of mqtt_3_1_0_proto_desc and mqtt_3_1_1_proto_desc were logged
with following code:
MQTT_TRC("Encoding Protocol Description. Str:%s Size:%08x.",
mqtt_proto_desc->utf8, mqtt_proto_desc->size);
This resulted in invalid log, since they were not NULL-terminated
strings. Use MQTT_UTF8_LITERAL() to initialize both utf8 strings to make
sure they are NULL-terminated now and valid to print and
log. Additionally this makes the code a bit shorter.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Create a residency-based system power policy function for TI
CC13X2/CC26X2 that uses TI's Power module.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Added the functions to turn on/off the radio from LLL.
Added WAKE_IRQ to start radio after it's out of DSM.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Added the functions to turn on/off the radio.
Deep Sleep Mode (DSM)
Signed-off-by: Ionut Ursescu <ionut.ursescu@nxp.com>
Signed-off-by: George Stefan <george.stefan@nxp.com>
Ring buffer in memory backend does not depends on xtensa adsp board,
so make it general: remove to log_backend_rb and remove dependency on
up_squared_adsp.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of the 2Mbps BLE PHY on
VEGA platform.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
The radio on the VEGA platform supports both 1Mbps, as well
as 2Mbps BLE PHYs. It does not support coded BLE PHY. This patch
adds the necessary callback, as well as timings to enable the 2 Mbps
PHY support in the SW LL HAL for VEGA.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Add command to input the legacy pairing OOB TK during the pairing
procedure.
Fixed shell build with CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY defined.
Print error code when passkey input failed.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added CONFIG_BT_SMP_OOB_LEGACY_PAIR_ONLY option that completely disables
all legacy and SC pairing modes(except for Out of Band) and frees the
memory previously used by these.
Added CONFIG_BT_SMP_DISABLE_LEGACY_JW_PASSKEY option that force rejects
pair requests that lead to legacy Just Works or Passkey pairing.
Signed-off-by: Iván Morales <ivan98ams@gmail.com>
There are scenarios where there is a NAT firewall in between MQTT
client and server. In such case, the NAT TCP timeout may be shorter
than MQTT keepalive timeout and TCP timeout. The the MQTT ping
request message is dropped by the NAT firewall, so that it cannot be
received by the server, resulting in void MQTT ping response message.
There is no TCP FIN or RST at all. The application looks hang-up
until TCP timeout happens on the client side, which may take too
long.
Therefore, the event MQTT_EVT_PINGRESP is added to inform the
application that the route between client and server is still valid.
Signed-off-by: PK Chan <pak.kee.chan@nordicsemi.no>
This commit updates the the IPv4 ping command to handle the ENETUNREACH
error number returned by `net_icmpv4_send_echo_request` function when
IPv4 is unavailable.
The `net_icmpv4_send_echo_request` function previously returned EINVAL
when IPv4 is unavailable and this caused the shell command to report
"Invalid IP address" even when the provided IP address is correct; this
problem was corrected by returning ENETUNREACH instead of EINVAL in the
aforementioned function.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
net_icmpv4_send_echo_request currently returns EINVAL (invalid
argument) when IPv4 is unavailable.
Since the availability of IPv4 has nothing to do with the arguments
provided to this function and the meaning of EINVAL in this case is
ambiguous, return the ENETUNREACH (network is unreachable) error
number instead.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The TCP connection might be concurrently modified from the
TR/TX threads, so add a mutex to protect from the concurrent
modification.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
After removing the test windows, update test protocol
functions for the TTCN-3 sanity check.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
These test receive windows were used by TTCN-3 sanity check,
but it's possible to do without them.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to drop dependency on a heap, drop the
test send window.
Use net_tcp_queue_data() to receive the outgoing data
from the socket layer.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to drop dependency on a heap, drop the test
receive window.
The receive window was needed for TTCN-3 sanity check,
but it's possible to do without it.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
On incoming SYN+ACK, use the existing TCP connection.
This problem was overlooked earlier and was found while
testing TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In SYN_SENT check the ack number of the incoming TCP message
against our sequence number.
This problem was overlooked earlier and was found while
testing TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Don't erroneously instantiate an extra TCP connection
on TCP connect.
This problem was overlooked earlier and found while testing
TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
k_timer callback is executed from ISR context, which isn't
currenty compatible with Zephyr's shell implementation.
This problem was found while testing TCP2 client side.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to support TTCN-3 based TCP2 sanity check,
register test inputs with net_conn_register() and adjust
test functions to account for this.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
In order to support IPv4/IPv6, work with packet through
net_pkt_ip_hdr_len(), net_pkt_ip_opts_len() which account
for IPv4/IPv6, IPv4 options and IPv6 extension headers.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Remove temporary interception of TCP, UDP for TTCN-3 based
TCP2 sanity check.
As a part of adding IPv6 support, TCP2 will register test
callbacks/inputs with net_conn_register().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Allocate tcp2.c endpoints before storing port numbers or addresses.
Select the IPv4 source address since net_context_create_ipv4_new()
is not currently called on packet output.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Set initialization level of CDC ACM class to POST_KERNEL.
The proposed OpenThread Network-Coprocessor uses ACM. OpenThread is
started at POST_KERNEL level by the 802.15.4 radio drivers.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
The new version of mcumgr adds a few new Kconfig values, so
this commit adds them on Zephyr side.
This commit also updates west.yml so it points to the latest
changes on mcumgr's repo.
Signed-off-by: Miguel Azevedo <miguellazev@gmail.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Changes the behavior of the message cache to optimize for cache
capacity. Previously, the message cache's primary function was to avoid
decrypting messages multiple times, although the cache's main function
in the spec is to avoid message rebroadcasting. Optimizing for minimal
decryption causes us to fill the network cache faster, which in turn
causes more cache misses, potentially outweighing the advantage.
Now stores src + seq in message cache instead of field hash value. This
cuts cache size in two, while including more of the sequence number than
before.
Adds messages to the cache only after the packet is successfully
decrypted. This reduces noise in the cache, and ensures that no
invalid deobfuscations are added.
Additionally, this fixes a bug where multiple calls to net_decrypt with
the same packet failed, as the message cache found its own entry from
the previous call.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
NET_OFFLOAD interfaces do not handle ICMP request. Request to send ICMP
packet resulted in NULL pointer dereference in net_if_tx() later
on. Prevent that by detecting NET_OFFLOAD interfaces early in icmpv4
module.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This is a copy of rand32_timer.c that uses
z_do_read_cpu_timestamp32() instead of k_cycle_get_32(),
with some logic to ensure different values when called in
rapid succession missing.
Like the other driver, its reported values are not random,
it's a testing generator only.
This appears to have no advantages over rand32_timer.c,
just remove it. In QEMU emulation, the reported TSC values
tend to have the lowest five bits zeroed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
