The wdt CLEAR register is a write synchronized register.
To avoid bus stall, check the status of SYNCBUSY before
accessing the register.
Use SYNCBUSY register for SAM E.
If the wdt is syncing, return -EAGAIN to avoid bus stall.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Added a build-time assert to check if heap memory configuration to
make sure that it can accomodate RPMsg queue allocations.
Ref: NCSDK-5479
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
In case of control register lock, driver should return the error
immediately. Otherwise, error is later overwritten by
'rc = flash_stm32_wait_flash_idle(dev);'
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
ep_idx is common used designator for endpoint index,
rename ep_num to ep_idx in usb_dc_sam0 driver.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This commit adds a dependency on the TRNG resource in the TI Power
module, prevents the system policy from entering standby when TRNG is
active, and adds support for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Abort I2C transfers through the MCUX HAL if a transfer fails to avoid
deadlock in the driver/HAL.
Fixes#25098
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Reset gpio is configured during driver initialization. There is no
reason to do it repeat that process later, so replace
gpio_pin_configure() with gpio_pin_set().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Introduce sx1276_configure_pin() helper macro, which hides lots of
boilerplate preprocessor and C code. Doing so allows to uncover
inconsistent gpio initialization flow and prevent such in future. Also
add error log whenever gpio_pin_configure() fails.
It seems like output of gpio_pin_configure() for several
gpios (antenna_enable, rfi_enable, rfo_enable) was assigned to variable,
but its values was never checked. Return value from gpio_pin_configure()
of tcxo_power gpio was even not catched. The only output gpio
configuration that was handled properly was actually reset gpio.
Fix that inconsistent behavior by always checking return value of
sx1276_configure_pin().
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Fix flash operation timeout due to incorrect use of
secondary ticker to abort any radio in use. Ticker id 0
is reserved for split controller's pipeline preempt timeout.
Using the same ticker id caused the secondary ticker to
not be started if controller is using the same ticker id
for pipeline preempt timeout.
Fixes#26333.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Suppress -Wchar-subscripts warnings when building with Newlib, by
casting isdigit() parameter to unsigned char.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
LPC55xxx SoCs don't allow reading erased areas, the flash memory
controller (FMC) will trigger an ECC error for that area. To prevent
reading unwritten areas the low level FMC command of margin checking is
used, this will fail if the area to be read is not correctly written
(margin_check) or area is erased (blank_check).
In the case of an erased page, we return dummy data so the application
can program that area.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
In case of dualcore, STM32H7, STM32W and STM32MP1,
protect concurrent register write access with HSEM.
Done for following drivers:
clock_control, counter, flash, gpio, interrupt_controller
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. This pass DT information to driver instance to
ensure proper behavior.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Unit tests were failing to build because random header was included by
kernel_includes.h. The problem is that rand32.h includes a generated
file that is either not generated or not included when building unit
tests. Also, it is better to limit the scope of this file to where it is
used.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Since the i2c init structure is moved from config_info to the stack,
this change requires 12 bytes more stack during driver initialization.
This fixes#25255
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
wifi-reset-gpios flags were not respected so far. This means that
setting reset as active low (which is required in most cases for ESP
modules/chips) was done inside esp driver with inverted logic. Use dts
flags instead, so "active low" property is configured the same way as
for other drivers (i.e. in device-tree instead of driver).
This change also allows to configure reset as active high, in case where
ESP's nRST signal is somehow inverted on the board (behaving as RST
signal instead).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
PCI devices on 64 bit systems can be mapped anywhere, not just in the
lower 4G of memory. Remove pointer size assumptions.
Also this removes the use of a struct uart_device_config to store the
(runtime) BAR address. That struct has other stuff in it, and the
only thing we need is the single MMIO address. It's also REALLY
confusing to have two "devconf" fields in the device storing values of
the same struct type, some fields of which are used from one of them
but some from the other!
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The PCI API was originally limited to 32 bit addresses. Even though
it had code to skip over the high word in 64 bit BAR entries, it
refused to use it and returned a 32 bit value. Some devices in the
wild have default mappings from the firmware for devices above 4G.
Also remove the "iobar" API. It's dead code, we don't call it and we
don't test it. IO space BAR entries are a legacy feature from way,
way back in PCI history (I genuinely have never heard of a real device
that uses them!). And there's no difference in format between one of
these and a 32 bit "memory" BAR anyway, someone who actually had this
requirement could just use the existing API without worry.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
When checking the absolute value of cycles set to the comparator
use the MAX_CYCLES instead of MAX_TICKS.
The commit changes function names and comments to make it clear
where ticks (system ticks) and where RTC cycles are used.
Fixes#26701
Signed-off-by: Pawel Dunaj <pawel.dunaj@nordicsemi.no>
It is annoying to read just a single word at a time. Update this
command to print any amount of data. This uses byte format at present.
We could perhaps support something like:
flash read.8
flash read.16
flash read.32
to chose the size.
Example output (with line breaks to keep within git-style limit):
$ flash read FLASH_CTRL 0 20
00000000: 20 25 00 20 1d 26 00 08 69 68 00 08 45 26 00 08
| %. .&.. ih..E&..|
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
|........ ........|
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver blocks on a semaphore to receive notification when an
operation is complete, so requires CONFIG_MULTITHREADING=y.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since commit 5963ebaf33
("drivers: spi: CS configuration through devicetree")
the SPI GPIO CS flags are obtained from DT,
but the patch series has missed the necessary changes
for the ieee802154_dw1000 driver and decawave_dwm1001_dev board.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
K_FOREVER/INT_MAX number of ticks needs delay cycles value of
maximum order and exceeds 'int32' range.
The typecast to 'int32' results in wrongly evaluating the value
as less than 'MIN_DELAY' and chooses 'MIN_DELAY' over the actual
delay cycles.
Cap the 'MAX_TICKS' to INT32_MAX.
fixes: #26632
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Make sure to retry at least once after the timeout elapses. Sample the
current time before starting the i2c transaction, and only give up if
the polling occurred after the timeout.
The timeout exists to allow the eeprom time to complete a write, during
which time it will nack transactions (at24) or the status register will
report busy (at25). If a transaction fails legitimately, but the 1ms
sleep overshoots the timeout expiration, we will not try again, which
fails to give the part the full grace period before declaring failure.
This is likely to happen in the last 1ms interval but also possible if
the eeprom thread is preempted. It is possible to only try once and give
up if the sleep lasts longer than the timeout, which fails to give the
part an adequate period to complete the write.
Waiting until the current time is after (not equal to) the timeout is
also important because we don't want to round up partial milliseconds if
the start time was sampled near the end of a millisecond boundary. The
timeouts of eeproms can be ~5ms.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
A call to atomic_set_bit_to() was used for clearing bits in an atomic_t
variable that stores information about allocated GPIOTE channels.
This caused an issue to be reported by Coverity, as the function treats
its first parameter as an array and it was provided with a pointer to
a singleton.
This commit replaces that call with atomic_and(), to prevent the issue
from being reported and for consistency with the way bits are set for
allocated GPIOTE channels (what is done with a call to atomic_or()).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The STOPTX task cannot be triggered directly in the function that
disables TX interrupt because this task stops the UART transmitter
immediately, even if it is in the middle of shifting out a byte.
Instead, this task needs to be triggered in the interrupt handler,
when the end of transmission is signaled.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
To keep the bus fully loaded, the SAM0 has a fast path that recognises
special cases like TX only, RX only, or TX/RX of the same size.
Commit #ea2431f32f7 accidentally disabled this.
This increases the utilisation from around 30 % to around 90 % at 48
MHz.
Signed-off-by: Michael Hope <mlhx@google.com>
The SAM0 has a data register and a shift register. Data that is
written to the data register is transferred to the shift register by
the peripheral.
On the SAMD51, the CPU is fast enough that the first data write hasn't
been transferred to the shift register by the time the next data write
occurs, causing the second write to be dropped, causing the receiver
to wait forever.
Fix by spinning until the data register is empty.
Signed-off-by: Michael Hope <mlhx@google.com>
The gd7965 driver still called ksleep with unsigned integers.
Use the K_MSEC makro instead.
Signed-off-by: Tobias Schaffner <tobiasschaffner87@outlook.com>
Adds the chip select devicetree flags to the spi_cs_control instance.
ISM43362 chip select is ACTIVE_LOW.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Fix host RX thread being deadlocked. The deadlock occurs because the
RX thread is stuck waiting in conn_tx_alloc with K_FOREVER but if the
connection is disconnected only the RX thread can unblock it in the
handling of the disconnect event.
This commit fixes this deadlock by splitting the processing of the
disconnected event into two parts.
The part needed to unblock the RX is to release resources held by
unack'ed TX packets and mark the connection state as not connected
anymore.
The RX thread waiting for free_tx fifo and the TX thread waiting for
the bt_dev.le.pkts semaphore will both check the connected state after
having acquired them and will abort if disconnected.
The rest of the processing will be handled at normal RX thread
priority like normal.
Move the bt_recv_prio handling to the Bluetooth host when the host
has defined its own RX thread (CONFIG_BT_RECV_IS_RX_THREAD=n).
If the HCI driver has the RX thread (CONFIG_BT_RECV_IS_RX_THREAD=y),
then the responsibility to call bt_recv and bt_recv_prio correctly
falls to the HCI driver.
The helper function bt_hci_evt_is_prio() is replaced with
bt_hci_evt_get_flags() so that the HCI driver can do this correctly.
This decision to replace was made so that existing HCI drivers
maintained out-of-tree will fail at compile time with the new system.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth: host: Move bt_recv_prio to host when RX thread is defined
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
We should not set PLLSRC bits here. It is done by
LL_PLL_ConfigSystemClock_* functions which are called later.
Also, PREDIV1 setting should not be restricted to HSE only.
Signed-off-by: Ilya Tagunov <tagunil@gmail.com>