Whenever a buffer is sent to the driver via bt_raw using bt_send() the
buffer might not be consumed if an error is returned. In that case
unreference the buffer to avoid leaking the already allocated net_buf.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Currently, we don't have a .conf which enabled BT. This will be
re-enabled at some future date after migrating to the full net_app
APIs by setting CONFIG_NET_APP_BT_NODE=y.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
There were bunch of config options in tests/net, net-shell and
wpan_serial sample, and those options had wrong name so they
were ignored by the code.
Fixes#1428
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is a simple shell module that allows arbitrary boards with flash
driver support to explore the flash device.
- Reading, erasing, and writing by device offsets are supported in all
cases.
- If the flash page layout is available, it can be printed, and I/O
can also be done to a specified page as well.
One known issue is that writing to flash on targets that require
doubleword-sized writes (e.g STM32L4) will fail since the number of
arguments required exceeds ARGC_MAX in shell.c. Addressing that is
left to future work.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Added sample code for testing and displaying the flash layout using
the recently introduced API.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
bbc_microbit has been observed to regress on this sample and is
therefore a good candidate for CI.
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
To test BMM150 geomagnetic sensor driver in polling mode,
sample application added by this patch can be used.
Signed-off-by: Punit Vara <punit.vara@intel.com>
The IP header was stripped by _net_app_ssl_mux() when it received
IP packet. This is fine but if the application expects the get
the IP header, then there is a problem. Fix this by saving IP
header to ssl_context and then putting it back in front of the
packet when the data is passed to application.
Note that this IP header is not used by net_app when the packet
is sent because TLS/DTLS creates a tunnel for transferring packets
and user can only sent packets via this tunnel.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The default IPv6 multicast address count was too small,
increasing addresses to 5.
Jira: ZEP-2560
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The echo-server sample was using removed net_app_server_tls_disable()
function, the correct one is called net_app_server_disable()
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The stack name was incorrectly specified in mqtt_publisher sample
application, this cause compilation error when certain Kconfig
options were specified.
Jira: ZEP-2566
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server needs global enable/disable status instead of only being
able to enable or disable just the TLS server part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The main reason is allowing to run on 6LoWPAN devices, though also to
demonstrate IPv6 support with BSD Sockets in general.
Tested on 96b_carbon.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
POSIX requires struct sockaddr's field to be named "sa_family"
(not just "family"):
http://pubs.opengroup.org/onlinepubs/009696699/basedefs/sys/socket.h.html
This change allows to port POSIX apps easier (including writing
portable apps using BSD Sockets compatible API).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Normalizing variables names and make sure tag handling behavior, which
might be different among backends, does not make the test failing.
Also, improving debug logs in case of error.
Change-Id: Ic317948aab459bfa75c9a72ac48cb2d12a0d0706
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the encryption/decryption failed there is no need to procceed
further.
Change-Id: If450e40ed6fd601b698b74c56ae21fc7f903d087
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is how it's called in the main docs, so use this same phrase in
Kconfig and samples too.
Also, added some articles to docs.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Default BT_RX_BUF_COUNT value is not enough when transfering a large
amount of data (e.g. heavy network traffic over BT 6LoWPAN). Increase
BT_RX_BUF_COUNT from default value 3 to 10.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Be sure to check for NULL pkt in receive callback, which means TCP
EOF. The fix ported from echo_server sample.
Jira: ZEP-2423
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
C++ standard mandates that main() return an 'int' even though
Zephyr does not use it. Fix build error with XCC compiler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add cross-referenced information on the 96b_carbon and
96b_carbon_nrf51 pages which disambiguates between the two "boards".
Also describe how to flash 96b_carbon_nrf51 with
samples/bluetooth/hci_spi and 96b_carbon with samples/bluetooth/ipsp
to support a Bluetooth HCI stack on 96Boards Carbon (the physical
board).
While we're here, make the documentation page for 96b_carbon match the
format in doc/templates/board.tmpl.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Various of the printk messages in this sample app don't have
newlines. Let's fix the output by moving to SYS_LOG_xxx() macros
instead, which don't need them anyway. This also makes it easier to
tell errors apart from other messages, etc.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Add a sample application that allows a Zephyr-based Bluetooth
controller to interface with an HCI driver via SPI. This sample
implements the same BT SPI protocol already as Zephyr's HCI SPI
driver.
Currently, the sample only supports the legacy SPI API.
Provide a single configuration file, avoiding board-specific
files. Some board-specific configuration information must be provided
via other means:
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_DEV_NAME
- CONFIG_BT_CONTROLLER_TO_HOST_SPI_IRQ_PIN
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The documentation says that the API will automatically append the
net_buf fragment to the end of network packet fragment chain.
This was not the case and current only user for this API in
echo-server sample appended the fragment itself. The fix is to
automatically append the fragment to the end of fragment chain.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The hexiwear_k64 board can drive the leds with a pwm, so update the
rgb_led sample to work with this board.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64 board can drive the leds with a pwm, so update the
fade_led sample to work with this board.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The hexiwear_k64 board can drive the leds with a pwm, so update the
blink_led sample to work with this board. Reduces the maximum blinking
frequency from 500 Hz to 64 Hz because your eye can't distinguish these
higher frequencies (the led appears solidly on). Increases the minimum
blinking frequency from 0.5 Hz to 1 Hz because the mcux pwm driver can't
handle frequencies less than 1 Hz.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following test changes, log info have changes and previous log info
with stack guard present shows an mpu error not caused by a stack
overflow caught by mpu stack guard feature.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
This test launches several threads. Only last thread will overflow the
stack and an mpu exception will occur. The other threads are regulary
suspended, this triggers access to kthread structure. This tests is
failed on st and nxp platform, if 32 bytes alignement is not set.
Signed-off-by: Michel Jaouen <michel.jaouen@st.com>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
