On some SoCs the frequency of the system clock is obtained at run time
as the exact configuration of the hardware is not known at compile time.
On such platforms using CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC define
directly introduces timing errors.
This commit replaces CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC by the call
to inline function sys_clock_hw_cycles_per_sec() which always returns
correct frequency of the system clock.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
After the removal of the virtualcom DT node in 5071eee, using the chosen
node is no longer functional. Instead the Kconfig
CONFIG_UART_CONSOLE_ON_DEV_NAME is used to locate the correct UART.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Updated fs shell sample readme to state the requirement of a 32-bit
version of libfuse while building for native_posix board
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Sample applications for display functions do not work on native_posix_64
due to missing overrides. Clone the native_posix_64 Kconfig override
for all samples that have a native_posix Kconfig override.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The name disk_access_sdhc.c is ambiguous,
actually this driver depends on SPI,
rename this file.
In addition, move the generic sdhc stuff from C file
to head file for other sdhc drivers to use.
1) disk_access_sdhc.c->disk_access_spi_sdhc.c.
2) create .h and move sdhc specifications from .c to .h.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
We use the following commands to rename any
LED._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_LED._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l LED._GPIO_CONTROLLER | xargs sed -i 's/LED\(.\)_GPIO_CONTROLLER/DT_ALIAS_LED\1_GPIOS_CONTROLLER/g'
git grep -l LED._GPIO_PIN | xargs sed -i 's/LED\(.\)_GPIO_PIN/DT_ALIAS_LED\1_GPIOS_PIN/g'
git grep -l LED._GPIO_FLAGS | xargs sed -i 's/LED\(.\)_GPIO_FLAGS/DT_ALIAS_LED\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We use the following commands to rename any
SW._GPIO_{CONTROLLER,PIN,FLAGS} to
DT_ALIAS_SW._GPIOS_{CONTROLLER,PIN,FLAGS}
git grep -l SW._GPIO_CONTROLLER | xargs sed -i 's/SW\(.\)_GPIO_CONTROLLER/DT_ALIAS_SW\1_GPIOS_CONTROLLER/g'
git grep -l SW._GPIO_PIN | xargs sed -i 's/SW\(.\)_GPIO_PIN/DT_ALIAS_SW\1_GPIOS_PIN/g'
git grep -l SW._GPIO_FLAGS | xargs sed -i 's/SW\(.\)_GPIO_FLAGS/DT_ALIAS_SW\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
move misc/reboot.h to power/reboot.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/byteorder.h to sys/byteorder.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move ring_buffer.h to sys/ring_buffer.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move ipm.h to drivers/ipm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move disk_access.h to disk/disk_access.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move stats.h to stats/stats.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move nvs/nvs.h to fs/nvs.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move fs.h to fs/fs.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move console.h to console/console.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
USBD_CFG_DATA_DEFINE macro has not consider that a class
could have more than one set of usb_cfg_data struct.
If a class has more than one set of usb_cfg_data
then they should be sorted the same way like by
USBD_DEVICE_DESCR_DEFINE macro.
Fixes: #16240
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This patch removes the "hard" selection of the USB_DEVICE_REMOTE_WAKEUP
Kconfig option for USB devices made on the nRF52840 SoC. Now it's up to
the application to decide if it wants to enable the option. This change
makes it possible to pass the USB3CV Chapter 9 Tests for applications
that don't use the remote wakeup feature, since when a USB device only
reports that it supports this feature, and the mentioned option makes
it to do so, one of the test cases expects the USB device to actually
perform the remote wakeup. And when the feature is not reported as
supported, the test case is skipped.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample has to be operated manually (it's a USB DFU implementation
that needs to be plugged into a host to validate). Sanitycheck is
failing right now becuase it tries to flash and run it, and doesn't
see a harness declaration.
Set it to build_only when run under sanitycheck.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Right now this fails needlessly under sanitycheck for lack of a
harness declaration. It's short, just stuff in a simple regex check.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fix misspellings and doc issues missed during regular reviews (including
some files without a trailing newline)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Cleanup references to boards in some of the example and use the same
boards through the examples. Other minot cleanups and make the text more
generic and not specific to certain boards.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
It does make sense to initialize USB console after USB Device stack.
Note that the value is selected only if we specify USB_UART_CONSOLE
in prj.conf, not in menuconfig afterwards.
Fixes#16518
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This allows setting a custom pointer to be passed back to the complete
callback at expense of increasing the buffers in 4 bytes.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Remove duplicated execution path for composite configuration, USB
device stack initialization is done inside stack for both cases.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
In order to unify the legacy and composite code, move the class and
vendor request handler buffer into the USB device code, just like in
composite mode. The option is renamed from USB_COMPOSITE_BUFFER_SIZE
into USB_REQUEST_BUFFER_SIZE and also replaces the USB_DFU_MAX_XFER_SIZE
and USB_HID_MAX_PAYLOAD_SIZE options.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Sample walk through:
1. CPU 0 will wake up CPU 1 after initialization
2. CPU 1 will send to CPU 0 an interrupt over MHU0
3. CPU 0 return the same to CPU 1 when received MHU0 interrupt
4. Test done when CPU 1 received MHU0 interrupt
The wake up second core and private core ID are soc specific.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
