Aligns MAC registers to the latest reference manual.
Replaces NULL buffers as some SPI drivers will fail.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
uint8_array values are now generated as structure initializers. Update
the code accordingly. The implementation assumes that existing
devicetree source does not provide the correct OUI so preserves the
in-driver override of the value provided by devicetree.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Remove magic numbers from Ethernet drivers and tests by defining
NET_ETH_MAX_DATAGRAM_SIZE and NET_ETH_MAX_FRAME_SIZE.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fix calculation of frame length in eth_enc28j60_rx().
The calculation was incorrect because the CRC size was
subtracted only from the lower byte.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Use the new API where relevant. Only sam_gmac is left aside for now.
This simplifies a lot the code as the caller should only care about
allocating net_pkt and its buffer once, and thus will not need to mess
with "frags" etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We now generate CS GPIO defines from the DTS that we can utilize. We
needed to slightly update the #defines in the driver from:
DT_MICROCHIP_ENC28J60_0_CS_GPIOS_{PIN,CONTROLLER} to
DT_MICROCHIP_ENC28J60_0_CS_GPIO_{PIN,CONTROLLER}
Fixes#12640
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There is no need to reserve any space for each frag, as the l2 will
allocate a frag for the ethernet header, arp will do the same.
This is one step further to removing the concept of ll reserve.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Update such statistic on all drivers.
Also, remove TX stats in native and stellaris drivers: such update is
done in L2 now.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now instead of such path:
net_if_send_data -> L2's send -> net_if tx_queue -> net_if_tx -> driver
net_if's send
It will be:
net_if_send_data -> net_if tx_queue -> net_if_tx -> L2's send -> driver
net_if's send
Only Ethernet is adapted, but 15.4 and bt will follow up.
All Ethernet drivers are made compatible with that new scheme also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
After read first packet and if ERDPT < ERXRDPT,cause read Rx FIFO error.
The fix is to set ERDPT properly before reading next packet.
Fixed#9537
Signed-off-by: Frank Li <lgl88911@163.com>
- tx_tsv is never used anywhere
- and rx_rsv can be allocated on stack
Optimizing a bit the stack usage in eth_enc28j60_rx() function as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
SPI API helps to directly transfer bytes from/to relevant buffers, so
let's take advantage of it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Driver is still a bit messy, not using for instance the 0-copy
capabilities of SPI API, but this will be fix later.
Constify most of the spi buf structures, removing useless variables,
renaming function with common prefix eth_enc28j60_ etc...
It seems to fix an issue on verifying if tx was successful as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Curently only link speed is exposed.
Opportunity taken to remove any post-fix enumerating the iface init
and/or the api: these must be generic and used by all the instances.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Let's use the new SPI API and ditch the old one.
Signed-off-by: Matthias Boesl <matthias.boesl@gmail.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The enc28j60's reception routine requires a timeout
for a buffer assignation. The timeout is configurable
to allow a per application fine tuning.
The effect that K_NO_WAIT currently has is that there are frames
lost everytime that a buffer is required and there are none
available.
Jira: ZEP-1169
Change-Id: Ia18736fd85daee51fe1c2304977209cc7f0038b5
Signed-off-by: Juan Manuel Cruz <juan.m.cruz.alcaraz@intel.com>
The code used net_nbuf_get_reserve_{rx|tx}_data() function to
allocate a fragment. Instead of that low level function, use
net_nbuf_get_frag() instead. There are few places this is not
possible or is too big change like in few test programs.
Change-Id: Ied7e2b7db352de998b200ffa6ff82471bfa5ebe3
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive lot of packets, it might happen that we exhaust
all the DATA buffers in the system. This would prevent from
us sending anything to the network.
Change this by splitting the DATA buffer pool into RX and TX
parts. This way RX flooding cannot consume all DATA buffers
that needs to be sent.
Change-Id: I8e8934c6d5fdd47b579ffa6268721b5eb3d64b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The interface L2 address type is set at the same time as the
L2 address is set to the network interface. This is most
convinient place to set the address type.
Change-Id: I712d7357d075959eb79df3463141cfbc6d163a74
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
