Add devicetree overlay for connecting an Mikroe ETH click shield to an
NXP LPCXpresso55S69 development board.
The LPCXpresso55S69 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ETH click board definition assumes SPI CS0.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Replaces .conf type configuration with .defconfig.
Makes configuration conditional, it depends on shield definition and
networking.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The current shield version shows different configuration, including
disabling default ethernet and wifi interfaces. To allow easy
connection from standard headers, this add two new shield designations.
The existing boards overlays and defconfig were updated.
The documentation was update to reflect changes. A new supported
variations section helps to understand what shield variation user need
select to build their own system.
This changes requires changes on esp32 offload tests to reflect new
esp_8266 shield designations. Sam4e_xpro was keeped as the only one
with dedicated overlay and both frdm_k64f and disco_l475_iot1 were
moved to use standard arduino r3 header using extra args.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The Atmel RF2xx module shield is a generic solution to enable any Atmel
AT86RF2xx IEEE 802.15.4 transceiver. This module enables IEEE 802.15.4
RF2xx Zephyr driver.
The Atmel RF2xx module shield enables any board with an Atmel Xplained,
Xplained-Pro, Arduino or MikroBus expansion header to connect to
networks operation with IEEE 802.15.4, OpenThread or any other stack
based on this media type.
The Atmel RF2xx module is configured to allow interoperate with other
medias like Ethernet. User need configure network stack properlly.
Fixes#26259.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since commit 5963ebaf33
("drivers: spi: CS configuration through devicetree")
the SPI GPIO CS flags are obtained from DT,
but the patch series has missed the necessary changes
in the device trees for displays and link_board_eth.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add devicetree overlay for connecting an Mikroe ADC click shield to an
NXP LPCXpresso55S16 development board.
The LPCXpresso55S16 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ADC click board definition assumes SPI CS0.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use the recently introduced mikrobus_spi devicetree node as parent node
instead of relying on mapping for arduino_spi.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Fixes whitespace in the frdm_kw41z shield document to allow continuation
in the numbered list of Bluetooth controller instructions and to format
the jumper configuration sublist correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Appropriate WS can be loaded automatically if
the display controller has integrated temperature
sensor or an external sensor is connected.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Removed flow control configuration from Kconfig and updated samples
to use device tree for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adds support for a new SHIELD, Eth Click.
Mikro-BUS type shield supported in Zephyr.
Adds Kconfig for mikroe_eth_click shield.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we phase out per instance Kconfig symbols convert to utilize
DT_DRV_INST to initialize CAN instances.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix node status to "okay" instead of "ok" which doesn't
seem to be in used anymore across the tree.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
x-nucleo-iks02a1 shield is an arduino compatible companion board
which can be used on top of Nucleo standard boards for industrial
applications. It extends the Nucleo functionalities adding following
MEMS sensor support:
- ISM330DHCX 3-axis accelerometer and 3-axis gyroscope
- IIS2MDC 3-axis magnetometer
- IIS2DLPC 3-axis accelerometer
- IMP34DT05 digital microphone.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add ESP-8266 modules shield. The ESP-01 needs to be loaded with
ESP8266 AT Bin V1.6.2 which is compatible with ESP8266 AT Bin
V1.7.x which is the minimal supported version by ESP WIFI driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add shield definition for the MikroElektronika ADC Click. The ADC
Click carries a MCP3204 12-bit Analog-to-Digital converter in a
mikroBUS form factor.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The LIS3MDL driver handles DRDY interrupt only. So connect
trigger to the DRDY pin instead of the INT pin.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There is a blue LED used to display connectivity for the SparkFun
SARA-R4 shield. This LED is connected to the modem via GPIO 16
which is the default used by SARA-R4 driver when
CONFIG_MODEM_UBLOX_SARA_R4_NET_STATUS is enabled.
Signed-off-by: Michael Scott <mike@foundries.io>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
