This simulates a reboot by jumping back to the address stored in the
reset vector in vector table found at address 0. It is supported from
interrupt/exception level, which means that sys_arch_reboot() in this
case finds out if it is called from thread mode or handler mode, and in
the latter case, it unwinds the nested exception stack as needed.
Change-Id: Ib67f850f8411f1ee8fc592a5f31f2f70d0af14a4
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The bootloader expects the entry point to be called __start, not __reset.
Change-Id: I5a5f7f45c248b9398e58fb026c731f8617fe4856
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Add sys_exc_connect() (and its x86-compatible alias nanoCpuExcConnect())
that allows connecting an exception handler at runtime.
The current implementation is a bit of a bastard, to avoid disturbing
the current implementation of the exception handlers. Instead of hooking
_exc_wrapper() in all vectors and adapting the exception handlers, the
current exception handlers are still hooked directly in the vectors.
When an exception is hooked at runtime, _exc_wrapper() gets installed in
the vector and the real handler gets inserted in _sw_exc_table; this
means that the scheme only works with non-XIP kernels.
This should be enhanced so that _exc_wrapper() is hooked in all vectors,
and that current exception handlers (for faults mostly) are reworked to
be inserted in the _sw_exc_table and wrapped in _exc_wrapper().
Change-Id: Icaa14f4835b57873d2905b7fbcbb94eeb3b247d1
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
For non-XIP systems, it's not in ROM, so remove the "ROM" part. Adapt it
to coding conventions at the same time, and export it to C code.
Change-Id: Id09a6be8bc9c462667ed71b53be7fa5382c88db3
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Find out on which stack the stack frame for an exception is in the assembly
code (__fault()) rather than in C (_Fault()). This will allow pushing
more registers on the stack when debugging is enabled.
Change-Id: I1c510b83098536f8930392b17df27511ccd04d80
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename the function and allow it to handle the 'type'
argument, which is ignored in this case.
Change-Id: I3d3493bea4511b2d026747505e7e52c5acc85012
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The ESF was built using the 'alias' names of the GPRs (a1, lr, pc, etc)
rather than their 'real' name (rN).
Change-Id: I49cae5e94869a79a3165dc7f2347d8cec39dbf67
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The processor is made aware that the vector table built in the image is
located at the start of SRAM in the case of a non-XIP image, rather than
at 0 in as is the case in XIP images.
Change-Id: I40b28ca32daf3e8930f103224766ed4e0ccc88e0
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The image will be linked at a different address and with different
ROM/RAM sizes to allow running a bootloder image that loads a payload
image. The addresses/sizes depend on if it is a XIP image or not
(CONFIG_XIP), and in the case of a XIP image, if it is a bootloader
image (CONFIG_IS_BOOTLOADER) or not.
In the case of a bootloader, it is given the full ROM and
CONFIG_BOOTLOADER_SRAM_SIZE kB of SRAM. When not a XIP image, it is given
the full SRAM minus CONFIG_BOOTLOADER_SRAM_SIZE kB, and is linked at the
start of SRAM.
Change-Id: Ibbb693c7bff022f313dac40f21c04a61f4bed115
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
This board needs 16 bytes to be written with a specific value when the
target boots. This is only necessary when running a XIP image which
exists around those 16 bytes.
Change-Id: Ifd26b3842f09137765d9c7d1678476bfda8a563f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Fix an issue where, if a task is pending on a nano timeout, the duration
it wants to wait is not taken into account by the tickless idle code.
This could cause a system to wait forever, or to the limit of the timer
hardware (which is forever, for all intents and purposes).
This fix is to add one field in the nanokernel data structure for one
task to record the amount of ticks it will wait on a nano timeout. Only
one task has to be able to record this information, since, these waits
being looping busy waits, the task of highest priority is the only task
that can be actively waiting with a nano timeout. If a task of lower
priority was previously waiting, and a new task is now waiting, it means
that the wait of the original task has been interrupted, which will
cause said task to run the busy loop on the object again when it gets
scheduled, and the number of ticks it wants to wait has to be recomputed
and recorded again.
Change-Id: Ibcf0f288fc42d96897642cfee00ab7359716703f
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Adds C++ support to the build system.
Change-Id: Ice1e57a13598e7a48b0bf3298fc318f4ce012ee6
Signed-off-by: Dmitriy Korovkin <dmitriy.korovkin@windriver.com>
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Adds extern "C" { } blocks to header files so that they can be
safely used by C++ source files.
Change-Id: Ia4db0c36a5dac5d3de351184a297d2af0df64532
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Introduce the GPIO QMSI-based implementation. This is basically a
shim layer that implement's Zephyr's GPIO APIs on top of QMSI drivers.
This is an alternative driver that conflicts with the previous
GPIO_DW implementation. In order to enable it you must set:
- CONFIG_GPIO=n
- CONFIG_GPIO_QMSI=y
- CONFIG_GPIO_0=y
- CONFIG_QMSI_DRIVERS=y
- CONFIG_QMSI_INTALL_PATH="PATH_TO_QMSI"
Note that this driver currently only supports one controller instance,
GPIO_0. It is implemented this way due to a limitation from the current
version of QMSI. QMSI versions later than 1.0 doesn't have this
limitation.
Missing:
- support multiple controller instances (gpio_0, gpio_1, etc);
- enable level triggered interrupts in sync with system clock,
through setting INT_CLOCK_SYNC properly.
Change-Id: Ib61b153dae9741806a9a31d7dc1f82b96d000fbe
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
It wasn't immediately clear in _execute_handler() that
enable_interrupts() didn't actually do anything if
CONFIG_NESTED_INTERRUPTS wasn't enabled.
If we are not using nested interrupts, perform small optimization
1) The call to disable interrupts isn't necessary as interrupts
are already disasbled
2) The check for !_nanokernel.nested in a couple places always
evaluates to true if nested interrupts aren't used
Change-Id: I7e66cee0466d03bc1172a572e19389accf6e0e62
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
On Quark SE, SPI might require GPIO to be ready before hand, to emulate
CS, thus providing an option to tweak the intialization priority for SPI
DW driver.
Change-Id: Ifa373948ac8227bf6e4ed1113bcb4dc9139b6663
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Enable both controllers by default if GPIO is enabled, providing all the
necessary information.
Change-Id: I5aab00324b10492eefb67e9595da491775cbd95d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no such thing as "IA" in Quark SE SS as it is an ARC core. Plus
for this very specific feature it does not require the ARC aux regs
instruction to read/write in the given mask address.
And fixing also the CONFIG_ option to check.
Change-Id: I1f63348ec85f6e006795f7641c912a30fc003709
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Quarks SE owns a GPIO controller which is always on (so not clock-gated)
thus providing it base address, the pins it handles etc...
Change-Id: Ifceb7cb74e763a91130d615ba19756ddcbe97a23
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is valid only for Quark SE and Quark SE SS, where it requires to
unmask the interrupt for each specific controller. Thus making the
function generic, using the parameter as the specific mask base address.
Change-Id: Iea0a412b8d94a1ab5e1f3e339eaf632eacee5797
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We can save a great deal of RAM this way, it only needs to be
in RAM if dynamic interrupts are in use.
At some point this config option broke, probably when static
interrupts were introduced into the system.
To induce build (instead of runtime) errors when irq_connect_dynamic()
is used without putting the table in RAM, the dynamic interrupt
functions are now conditionally compiled.
Change-Id: I4860508746fd375d189390163876c59b6c544c9a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The original value of 128 was selected more or less randomly, and
isn't sufficiently large enough for QA needs.
Change-Id: I8a9fcc86d6b5fa7dc5ba05896c62f7dd608f9ed2
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This adds driver for the UART controller on Atmel SAM3X8E.
This UART controller only has two wires for RX and TX, and
does not have flow control (e.g. CTS, RTS) or FIFO.
Currently, the driver does not support any interrupt driven
operations.
Change-Id: I63720bccfb70a89888353b8ee3dfc4b80793dc01
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This adds initial support for Atmel SAM3X8E processor, which is
based on ARM Cortex-M3. The SAM3X8E is being used on Arduino Due.
Change-Id: I199efcf29629f9ebacad474e5edc91bc3757f613
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This removes the default flash and SRAM base addresses from the ARM core
Kconfig file. Each individual SoC/processors Kconfig has to define them.
This is in preparation to support Atmel SAM3 family processors as they
have different base addresses.
Change-Id: I97ea9b43386d1e286ee692f583c97cfbb5399b0f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This reverts commit 778d5b11c5327be4b40c7745e9beaecfd6327e13.
This patch has been identified as breaking the build when trying
to manually build non-x86 applications.
Change-Id: I1857745049dfef7193de58737108314b7aae01c5
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This option misunderstands how XIP works. The IDT is ALWAYS in ROM,
the question is whether crt0 will copy it into RAM or not. You can't
save ROM space in this way.
Change-Id: I58025e3d71ead35730d0a5026213299b4fcb5eb9
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These are not (yet) used anywhere and generate unnecessary warnings.
Just remove them.
Change-Id: Ibae472c4a639466c221cdc354232780db04e963e
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This converts the i2c_quark_se_ss to use the static IRQ API.
Note that, even with separate config functions for each instance of
the driver, it is still saving both RAM and ROM space.
Change-Id: Ieb555ff281b384d87d8e69f6914878bbee0e2ee9
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Define configuration for Nordic chip connected to UART0.
Change-Id: Ia6007def747932e5f9fbd57f1ea8005892a2f793
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Decisions on compiler optimizations were done on the architecture level,
this does not scale and some SoCs will have different optimization levels
or compiler options needed. Moving this to the SoC makes it easy to optimize
differently when using the same CPU which we use to set the right optimization
now on the architecture level.
For IAMCU platforms, use the right architecture and tuning.
-march=lakemont -mtune=lakemont -miamcu -msoft-float
Change-Id: I0f77cffe7a139f8b2620935094437d0dfd160dfe
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The Kbuild system first looks for a Kbuild file, then it looks for
a make file.
Use the Kbuild for object building and leave the Makefile for definding
build options and compiler flags and other SoC related defines.
Change-Id: I0be59bb5ae02a29108a188efbd6f14dcdb7de4ee
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Currently, if we disable I2C_DW through 'menuconfig', I2C_DW_0* and
I2C_DW_1* options are not disabled even if they depend on I2C_DW
option. This makes the menuconfig confusing and we end up with the
wrong config set in .config file:
...
CONFIG_I2C_DW is not set
CONFIG_I2C_DW_0=y
...
CONFIG_I2C_DW_1=y
...
This patch fixes this issue by surrounding the I2C_DW_0* and I2C_DW_1*
options with 'if I2C_DW'.
Change-Id: I7e949b066425bca2533f8b84b9ea7b1915369ff0
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
On SysV ABI, the NANO_ESF parameter is passed in via the stack.
For IAMCU, this is instead expected to be in EAX.
_ExcEnter is currently using EAX to stash the return address of
the calling stub while it does a stack switch. Change it to use ECX
for this purpose, and if we are running with IAMCU place the
parameter in EAX instead of pushing it.
The output of the fault handler has been cleaned up a bit and it
now also includes the code segment.
Change-Id: I466e3990a26a1a82dd486f3d8af5395eab60b049
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Instead of relying on the Kconfig variables use a common scheme for
naming i2c devices and use it directly in application.
Change-Id: I745af68d7c1767cc8a24f9655fa45fa33f6baf93
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This was never implemented on ARC/ARM and has been superseded
by irq_offload().
Some checks that were only done with CONFIG_LOAPIC_DEBUG fall
under the category of 'shouldn't ever happen' and have been
converted into assertions, instead of propagating return values
which are largely never checked.
Change-Id: I4eedca05bb7b384c4f3aa41a4f037f221f4a9cfe
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This patch introduces the 'QMSI RTC device driver' which is simply a shim
driver based on RTC driver provided by QMSI BSP.
Some config options are independent of the driver implementation used,
so use a consistent name for them. In this case RTC Interrupt number and
Priority use the same config options for both the QMSI and DesignWare
drivers.
In order to enable this driver, the following options should be set:
CONFIG_QMSI_DRIVERS=y
CONFIG_QMSI_INSTALL_PATH="/path/to/libqmsi/directory"
CONFIG_RTC=y
CONFIG_RTC_QMSI=y
Change-Id: I48292406e5472e5786f3b9abbeb71016a273bfec
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
The ARC EM family processors do not support native atomic assembly
instructions (LLOCK and SCOND). Therefore, the assembly version
of atomic functions cannot be used. This adds pure C version of
these atomic functions.
Change-Id: Ic64dd31b0367b6dcf3a46f41c0c7ac2c2ce5eb8d
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
If we are not doing any dynamic interrupts or exceptions, we
can put the IDT in ROM and save a considerable amount of RAM,
up to 2K if the IDT is the default size of 256 entries.
The _interrupt_vectors_allocated table can also be put in ROM
if we're not using any dynamic interrupts.
We introduce a new Kconfig option to force the IDT to be in RAM
for situations where no dynamic IRQs are used, but ROM footprint
needs to be conserved.
Change-Id: I38c9f1a8837b4db9f3dea1caa008374a26cbbf1d
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This enables building with the iamcu variant of the x86 compiler
and enabled using the IAMCU ABIs.
Change-Id: Idf71251898e250b8df73c065462c93c289879fe2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are a few bits missing on enabling I2C controller on
quark_d2000_crb. This adds the missing bits.
Change-Id: I05bbe8367a9e69962db573d496f1f9f0167ba597
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
