We always have UART_IRQ_FLAGS set to 0, so just call IRQ_CONNECT with a
0 argument for the flags, and remove the UART_IRQ_FLAGS. This is
towards support for using the driver on the TI CC2650. (we add a
comment about that as well).
Signed-off-by: Geoffrey Le Gourriérec <geoffrey.legourrierec@smile.fr>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clearing fields in the region descriptor attributes doesn't always have
the expected effect of revoking permissions. In the case of bus master
supervisor mode fields (MxSM), setting to zero actually enables read,
write, and execute access.
When we reworked handling of region descriptor 0, we inadvertently
enabled execution from RAM by clearing the MxSM fields and enabling the
descriptor. This caused samples/mpu_test run to throw a usage fault
instead of an MPU-triggered bus fault.
Fix this by setting all the MxSM fields to 2'b11, which gives supervisor
mode the same access as user mode.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
1. Changed _tsc_read() to k_cycles_get_32(). Thus reading the
time stamp will be agnostic of the architecutre used.
2. Changed the variable names from *_tsc to *_time_stamp.
JIRA: ZEP-1426
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Add a separate section in the linker to place the MMU configuration
information. This location is read by the gen_mmu.py script to
create the actual page tables.
JIRA: ZEP-2095
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
In crt0.S the MMU is initialized. It uses the statically build
page tables. Here 32-bit paging scheme is used, thereby each page
table entry maps to a 4KB page. The valid regions of the memory are
specified by SOC specific file(soc.c).
JIRA: ZEP-2099
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Makefile rule to create the MMU page tables at boot time. This
rule invokes the gen_mmu.py script to create a binary which is
then placed into the kernel image using objcopy.
Makefile.mmu is included only when CONFIG_X86_MMU is enabled.
JIRA: ZEP-2095
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Macro is used to create a structure to specify the boot time
page table configuration. Needed by the gen_mmu.py script to generate
the actual page tables.
Linker script is needed for the following:
1. To place the MMU page tables at 4KByte boundary.
2. To keep the configuration structure created by
the Macro(mentioned above).
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Kconfig definition for enabling the memory management Unit
on x86 based platforms.
JIRA: ZEP-2093
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
The .balign directives were not working correctly in their
previous positions as the directive was applying to the section
before the variable's section, causing in some builds the
variables to be misaligned, and accesses to them causing faults.
With the alignments after the section declaration, the variables
will now be aligned as specified. Any future variable declarations
should use this form instead to ensure proper alignment.
Signed-off-by: Michael R Rosen <michael.r.rosen@intel.com>
Both the ARM and NXP MPU drivers incorrectly calculated the region index
by assuming the region type (e.g., THREAD_STACK_GUARD_REGION) was
zero-indexed, when in reality it is one-indexed. This had the effect of
wasting one region.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The NXP MPU requires special handling of region descriptor 0 to
guarantee that the debugger has access to the entire address space. It
does not allow writes from the core to affect the start or end
addresses, or the permissions associated with the debugger.
The original implementation of this driver attempted to work around
region descriptor 0, resulting in an off-by-1 error caught by Coverity.
Instead, define region descriptor 0 explicitly in the mpu_regions array,
and add some asserts to ensure that one doesn't try to change its start
or end addresses. This has an added benefit such that more permissions
can be enabled in region 0 if desired, whereas the previous
implementation always forced all writable permissions to be cleared.
Coverity-CID: 170473
Jira: ZEP-2258
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The original implementation of _get_num_regions() parsed the CESR[NRGD]
register field to determine the number of mpu region descriptors
implemented in hardware. There was a possible path in the code to return
zero, which would cause underflow later on in arm_core_mpu_configure().
Coverity complained despite an assert to catch this condition. Instead,
use a preprocessor macro from mcux that defines the number of mpu region
descriptors.
Coverity-CID: 169811
Jira: ZEP-2208
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Stack sentinel doesn't prevent corruption, it just notices when
it happens. Any memory could be in a bad state and it's more
appropriate to take the entire system down rather than just kill
the thread.
Fatal testcase will still work since it installs its own
_SysFatalErrorHandler.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
One of the stack sentinel policies was to check the sentinel
any time a cooperative context switch is done (i.e, _Swap is
called).
This was done by adding a hook to _check_stack_sentinel in
every arch's __swap function.
This way is cleaner as we just have the hook in one inline
function rather than implemented in several different assembly
dialects.
The check upon interrupt is now made unconditionally rather
than checking if we are calling __swap, since the check now
is only called on cooperative _Swap(). The interrupt is always
serviced first.
Issue: ZEP-2244
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The REGION bits (bit[3:0]) of MPU_RBAR register can specify the number
of the region to update if the VALID bit (bit[4]) is also set.
If the bit[3:0] of "region_addr" are not zero, might cause to update
unexpected region. This could happen since we might not declare stack
memory with specific alignment.
This patch will mask the bit[4:0] of "region_addr" to prevent updating
unexpected region.
Signed-off-by: Chunlin Han <chunlin.han@linaro.org>
The kernel tracks time slice usage with the _time_slice_elapsed global.
Every time the timer interrupt goes off and the timer driver calls
_nano_sys_clock_tick_announce() with the elapsed time, this is added to
_time_slice_elapsed. If it exceeds the total time slice, the thread is
moved to the back of the queue for that priority level and
_time_slice_elapsed is reset to zero.
In a non-tickless kernel, this is the only time _time_slice_elapsed is
reset. If a thread uses up a partial time slice, and then cooperatively
switches to another thread, the next thread will inherit the remaining
time slice, causing it not to be able to run as long as it ought to.
There does exist code to properly reset the elapsed count, but it was
only compiled in a tickless kernel. Now it is built any time
CONFIG_TIMESLICING is enabled.
Issue: ZEP-2107
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add necessary Kconfig and minimal device tree in order to support
STM32F412ZG variant as found on the Nucleo STM32F412 board.
Origin: Original
Change-Id: Ic98a686f478ce551dc6101466ed0cf16924109e8
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Following migration of stm32f1xx series clock control driver to
STM32Cube LL API, cleanup stm32 code base in order to take into
account that this is the only clock driver available for stm32
family.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following introduction of stm32cube LL based clock control driver,
remove references to former native driver.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Align stm32f1xx series clock driver to other parts of stm32 family.
Driver support both Connectivity and Density lines of stm32f1 series,
that are based on different Reset and Clock Control architectures.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The STM32F413ZH has 1536kB of Flash and 320kB of SRAM. This
configuration is currently not supported by ST MPU driver, so fill in
the blanks.
Note: The MPU does not support region size that is not a power-of-2 (see
the SIZE field in the MPU_RASR register). This is a problem for our
1536kB Flash region, so it was rounded up to the nearest choice. This is
possible because the memory in the range 0x0818000 - 0x0FFFFFFF is
"Reserved" and thus not mapped anyway.
Change-Id: If0c3d1db564ca45e77f8b5bafa2afdbafa85b40f
Signed-off-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
This reverts commit 37f4178f58.
This change builds gen_idt in the zephyr project tree instead of
building it in outdir of the application. The build process should all
happen inside outdir and no binaries should be placed in the zephyr
tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
pop {lr} instruction is not supported in ARMv6-M, fixed by
using pop {r0}; mov lr, r0; instructions.
Jira: ZEP-2222
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We now have generic ARM M4 MPU support added to Zephyr.
Let's enable it for use with Nordic nRF52 chips.
Memory Layout was generated from Section 8.3 "Memory
Map" of nRF52 Product Specifications (for both nRF52832
and nRF52840):
0x00000000: Flash
0x10000000: Factory Information Config Registers
0x10001000: User Information Config Registers
0x20000000: SRAM
0x40000000: APB Peripherals
0x50000000: AHB Peripherals
0xE0000000: ARM M4 Private Peripheral Registers
NOT Configured:
0x60000000: External RAM
0x80000000: External RAM
0xA0000000: External Device
0xC0000000: External Device
NOTE: More work will be needed for future Nordic MWU (Memory
Watching Unit) support.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This patch add arm core MPU support to NXP MPU driver.
With this feature it is now possible to enable stack guarding on NXP
MPUs.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The STM32L4x SoCs embeds a slightly different embedded flash controller
from the STM32F4x SoCs.
This particular controller has the following properties :
- Up to 2 512KiB banks divided in 2KiB pages
- Flash can be accessed in any sizes
- Flash must be written in 64bit aligned 64bit double-words
The drivers/flash/flash_stm32f4x.c is refactored into a new common
drivers/flash/flash_stm32.c and drivers/flash/flash_stm32l4x.c is
created with the STM32L4x specific functions.
To ease the refactoring and keep common functions, the STM32L4x flash
headers are slightly modified to match the hardware reference naming
and solve compilation issues.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Neither ASF nor CMSIS provide defines that can be processed by
the assembler. Exclude those from soc.h. Before this was done
incorrectly in board.h file.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch converts Atmel sam3x MCU series to use register
header files from Atmel Software Framework (ASF) library.
By using ASF different Atmel SAM MCU series can use common
device drivers.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This patch adds support for remaining Atmel SAM MCU series,
like sam3x to the common GPIO driver. After this update
full SAM MCU family should be supported by the driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Add configuration, dtsi and memory configuration fixup for the
STM32F469XI High Performance SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
