A number of sectors are declared in the frdm_k64f flash partitions
node as part of an "application state" partition. Rather than require
users to treat this area of flash as a single partition, delete the
application-state node and leave a comment in its place describing its
purpose.
This enables use cases where the flash sectors must be split into
multiple partitions without defining overlapping partitions in overlay
files.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Currently, flash partitions used by mcuboot are defined in the
SoC-level dtsi file for NXP K6X. This should be made more granular so
that product owners can choose partition layouts to suit their
needs. To that end, move the partitions into frdm_k64f.dts.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The I2C controller nodes are the root of the I2C bus for that controller
and thus may have children nodes that represent the I2C devices on that
controller. Thus we need to specify the #address-cell & #size-cell
properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
+ The VBLUno52 board
nRF52832 ARM Cortex-M4F processor
Bluetooth Low Energy 5.0
DAPLink interface
UNO pinout
4 power
+ The following samples were tested:
hello_world
basic/button
basic/blinky
bluetooth/peripheral_hr
bluetooth/beacon
Signed-off-by: Nam Do <robotden@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SimpleLink SDK provides a peripheral driver library and hardware
register access header files for the Texas Instruments SimpleLink
CC3220S and CC3220SF SoCs.
This patch updates the SDK version in Zephyr from 1.30.01.03
to 1.40.00.03.
The SDK can be downloaded from:
http://www.ti.com/tool/download/SIMPLELINK-CC3220-SDK
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
According to RFC7959 page 30, "The end of a block-wise transfer is
governed by the M bits in the Block options, _not_ by exhausting the
size estimates exchanges."
Therefore, we should check the M bit instead of total size (which
is not always available, too)
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When the controller is configured to have its worker and job
be run at different interrupt priority, check for mayfly
priority being equal was incorrect.
Fixed by conditionally compiling the correct check of mayfly
priority level.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed a defect wherein anchor for first scanner event was in
the past (when looking for a free timeslice to avoid
overlapping with master role events) when actually there
were no master roles active. This defect caused the scanner
role to assert, when started with other roles active (eg.
advertiser), when trying to catch-up to current tick.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit 3c23c6f53d ("Bluetooth: controller:
Fix assert due to stale tick count") as this leads to
connection events to be skipped, failing conformance tests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This reverts commit b5235207d3 ("Bluetooth: controller:
Fix for scanner Rx window hang") as this leads to
connection events to be skipped, failing conformance tests.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If either UDP or TCP is enabled but not both, then connectivity
fails. This was a side effect of commit 3604c391e ("net: udp:
Remove NET_UDP_HDR() macro and direct access to net_buf")
Jira: ZEP-2380
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Commands for objdump and nm where hardcoded in size_report
script, which failed on MacOS as it tried to use ones from
Xcode. Fixed the script to pick the right objdump and nm
from the toolchain being used to build the application.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Its possible that #size-cells is 0 (ie i2c bus). So we should handle
either #address-cells or #size-cells being 0 in extract_reg_prop. This
means that the reg property in reduced map will end up being an integer,
so we need to convert it to a list with one element. We also need to
not output any address-cell or size-cell related info if the respective
cell is 0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
New top-level dts/ folder and description added.
Fixed error in bullet list in subsys/ description (needed
a blank like before the list.
Alphabetized folder list (subsys/ was listed after tests/)
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
When IPv6 fragments were sent, the last IPv6 fragmented packet
was accessing NULL pointer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fix calculation of T_Terminate and other procedure timers by
using ceil on calculated connection interval units.
This fixes TP/CON/MAS/BI-02-C [Master T_Terminate Timer] and
TP/CON/SLA/BI-02-C [Slave T_Terminate Timer] in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Ulrich Solli Myhre <ulmy@nordicsemi.no>
Fix implementation so that both slave and master behave same
during connection setup and generate disconnection complete
with reason 0x3e (connection failed to be established).
This fixes TP/CON/ADV/BV-02-C [Accepting Connections
Timeout] in LL.TS.5.0.0.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Signed-off-by: Ulrich Solli Myhre <ulmy@nordicsemi.no>
Whenever not using the whitelist the resolving list is traversed to
verify that the device is allowed depending on its current privacy mode.
In the case where the device is not found by address in the resolving
list, allow the request to go through, since we are then dealing with an
unknown devices and the resolving list restrictions do not apply.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Commit 1bc2fdc70 ("dts: arm: STM32 boards use DT to configure I2C")
added a new Kconfig option, HAS_DTS_I2C, which should be set when the
target supports configuration of I2C peripherals via Device Tree.
Currently, STM32 targets select this. However, the fact that
HAS_DTS_I2C has no default is causing prompting when building Zephyr
on other targets with DTS. To avoid this and allow builds to complete
as usual, have HAS_DTS_I2C default to n.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This causes num of packets command handling to dead lock since it
is done on RX buffer destroy if used on TX it may not be destroyed
on time causing.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This disable debug options in order for the image to fit in boards
such as arduino_101 and quark_se_c1000_devboard.
For convenience this adds another configuration file with as it was
available previously which can be build using:
make CONF_FILE=prj_dbg.conf
JIRA: ZEP-2378
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The specification states that the AdvA in a Scan Request packet should
be identical to the one sent in the original advertising packet, so
check this when processing a Scan Request.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When the initiator is using an RPA and we match it using the filtering,
we should return early and allow the device packet through instead of
going through the whole resolving list.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The specification states that filter policies shall be ignored for
directed advertising, so reflect this behaviour in the code.
Additionally when the local device is using RPAs but the peer uses an
identity address, the resolving list index needs to be updated when
traversing the RL to reflect that there has indeed been a device match
even though the IRK match did not happen.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The AdvA in the CONN_IND packet must match the AdvA in the advertising
packet that triggered it regardless of the advertising type.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added BUILD_ASSERT check for Tx and Rx thread priorities.
The Tx thread priority shall be higher than Rx thread
priority in order to correctly detect transaction violations
in ATT and SMP protocols. The Number of Completed Packets
for a connection shall be processed before any new data is
received and processed for that connection.
The Controller's priority receive thread priority shall be
higher than the Host's Tx and the Controller's Rx thread
priority.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Until Zephyr has infrastructure to enable/disable the
reception of multicast frames we disable the hardware
multicast frame filter completly and pass all multicast
frames to the upper layer and let that deal with them.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Some README files referenced wiki articles that have been
moved to the doc area on the website.
Fixes#668
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
When the ARP message is received when the device is starting up,
the network interface might not yet have IPv4 address setup
correctly. In this case, the IP address pointer could be NULL
and we must not use it for anything.
Fixes#752
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since we support uart0 on the cc2650 sensortag we should have a
reference for zephyr,console in chosen for it. This will be useful as
we start to generate Kconfig defines based on zephyr,console.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch add I2C to supported features and I2C section for
96b_carbon, nucleof401re and olimexino_stm32
It also adds serial port section to 96b_carbon and olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Frequency tolerance for LFRC after calibration for nRF5x
Series ICs is between 251 and 500 ppm as per Product
Specification. For more details refer to:
http://infocenter.nordicsemi.com/
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
