Rename the Kconfig option from BT_ISO_ADVANCED to
BT_ISO_TEST_PARAMS to more explicitly denote that it
enables support for using the ISO test parameters.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This updates the sys_kernel benchmark project to replace references to
the defunct TICKS_NONE symbol with K_NO_WAIT. It also removes the
outdated build instructions from the README.
Signed-off-by: Peter Mitsis <peter.mitsis@intel.com>
In 'test_access.c', model 3 on element 1 extending model 3 on element 0
is now registered correctly. When calling 'bt_mesh_model_extend' on
models on different elements, this needs to called from the
model with the highest element index to be registered correctly.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
Added overlay inside the spi loopback test for the
mimxrt1170_evk_cm7, enabled DMA and Async by default.
Added testcase for async and dma.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
The comparison of cycles we get with k_cycle_get_32 may be
incorrect if counter wrap happened. In case of ARC HSDK and
ARC HSDK4xD platforms we have high counter clock frequency
(500MHz or 1GHz) so counter wrap quite likely to happen if
we wait long enough. As in some test cases we wait more than
1 second, there are significant chances to get false-positive
assertion.
So let's skip nanosleep testcase for ARC HSDK and ARC HSDK4xD
boards.
The proper fix is to use k_cycle_get_64 in this test case,
but we need to provide k_cycle_get_64 support for ARC HSDK and
ARC HSDK4xD platforms first.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
When relocating section symbol addresses the value where the
relocation is to be written is an offset into the section to load.
Simply rewriting it with the section address is not enough, we need
to write the address of the section with the offset into it.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Split the conversion of the RTR frame flags from the data contents test as
RTR frames do not carry any data.
Replace a couple of direct DLC assignments with proper use of
can_bytes_to_dlc().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
as posix nanosleep is actually call us, so we need use a
higher clock to compare the result. try to use k_cycle_64
as possible.
Co-authored-by: Christopher Friedt <cfriedt@meta.com>
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
in test_nanosleep_execution, the
actual_ns = k_cyc_to_ns_ceil64((now - then * selection));
is wrong, according to posix driver code
lib/posix/clock.c
line: 156
if ((flags & TIMER_ABSTIME) == 0) {
ns += uptime_ns;
}
so we need change to
actual_ns = k_cyc_to_ns_ceil64((now + then * selection));
fixing: #62889
Co-authored-by: Christopher Friedt <cfriedt@meta.com>
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Rename z_early_boot_rand_get with z_early_rand_get to get consistent
with other early functions.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This reverts commit 341590545a, the issue
has been fixed in e1647e35c0, tested with
west build -t run -p -b qemu_riscv32_xip \
-T tests/kernel/xip/arch.common.xip
west build -t run -p -b qemu_riscv32_xip \
-T tests/kernel/xip/arch.common.xip.minimallibc
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Check whether peer is subscribed for ASE state notification before
calling bt_gatt_notify. This handles an assert thrown when the
notification failed to be sent.
Fixes: #63728
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Add verification of all stream's SDU, RTN and PHY rather than
just the first.
Also add another test case where only a subset of streams are being
reconfigured, but where the above values shall be updated for
all streams.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This commit increases the buffer used for commands
in the control channel within an instance of the
modem_cmux module. The buffer was not large enough to
store an MSC command if the optional break signals
where included. This commit fixes the issue and
updates the test suite to use the max size MSC message.
Signed-off-by: Bjarki Arge Andreasen <baa@trackunit.com>
Use the same pins as when testing with SIUL2 EIRQ interrupt
controller, but instead test routing the external interrupts
to WKPU controller.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
When configuring in/out pins for callback tests, pass the GPIO flags
coming from the in/out-gpios respective nodes.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
in case CONFIG_VL53L1X_INTERRUPT_MODE=n or
CONFIG_VL53L1X_XSHUT=n, the driver won't compile
Signed-off-by: Cyril Fougeray <cyril.fougeray@worldcoin.org>
Better group for logging tests removing verbosity and redundancy in
identifiers and making the sub-component a bit more uniform and clear.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This allow to run the following PTS test:
- DFU/SR/FD/BV-06-C
- DFU/SR/FD/BV-13-C
- DFU/SR/FD/BV-14-C
- DFU/SR/FD/BV-15-C
- DFU/SR/FD/BV-16-C
- DFU/SR/FD/BV-17-C
- DFU/SR/FD/BV-18-C
- DFU/SR/FD/BV-22-C
Signed-off-by: Pavel Vasilyev <pavel.vasilyev@nordicsemi.no>
The malloc arena/heap size setting can be adjusted using different
Kconfig options, depending on the libc implementation. This means
prj.conf can't be used to set this value on projects that can be built
for multiple libcs without generating a Kconfig warning.
Note: similar fix was applied for the hash_map sample, see
7ef8911e8c
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
rand32.h does not make much sense, since the random subsystem
provides more APIs than just getting a random 32 bits value.
Rename it to random.h and get consistently with other
subsystems.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Pass only speficied number of handler to read_params for GATT read
multiple. This is to avoid sending invalid (zeros) handles in
ATT_READ_MULTIPLE_REQ.
This was affecting GATT/CL/GAR/BI-18-C and GATT/CL/GAR/BI-19-C
qualification test cases.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
This was already excluded from
libraries.libc.newlib_nano.thread_safety.userspace.stress and it's now
failing in libraries.libc.newlib.thread_safety.userspace.stress as well.
The issue is being rootcaused to a toolchain issue but a proper fix has
not been identified yet, exclude that test as well in the meantime.
Link: https://github.com/zephyrproject-rtos/zephyr/issues/61129
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
