When we receive a packet with the sequence we already seen (and
processed), the most likely cause of it is that our ACK was lost,
and peer has to retransmit that packet. Then, we should just ACK
it, because otherwise peer will retransmit it again and again,
falling into exponential backoff and hosing the entire TCP
connection.
This makes changes to send_ack(), adding a flag to force sending
an ACK regardless of its cached status, and remove inline modifier,
as the function is big and called from many places.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
We must check if we receive RST in any of the TCP states.
If we do not do this, then the net_context might leak as it
would never be released in some of the states. Receiving RST
in any TCP state is not described in TCP state diagram but is
described in RFC 793 which says in chapter "Reset Processing"
that system "...aborts the connection and advises the user and
goes to the CLOSED state."
We need to also validate the received RST and accept only those
TCP reset packets that contain valid sequence number.
The validate_state_transitions() function is also changed to
accept CLOSED state transition from various other states.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With the support for 2M PHY added, the controller can now Rx/Tx
upto 18/19 minimum sized L2CAP packets per 7.5ms connection
intervals.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
net_if_get_default() was documented as returning "Default interface
or NULL if no interfaces are configured.", but actually didn't
return NULL in the latter case. Instead, it effectively returned
a pointer to random area of memory, shared with other system
structures, so calling functions like net_if_ipv4_set_netmask(),
etc. could trash unrelated memory.
Jira: ZEP-2105
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
RFC793, "Transmission Control Protocol", defines sequence numbers
just as 32-bit numbers without a sign. It doesn't specify any adhoc
rules for comparing them, so standard modular arithmetic should be
used.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
To better debug the flow of events into the Host, log the subevent code
whenever processing an LE Meta Event.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When required Rx MTU is less than configured Rx MPS, the
resultant initial credits was 0 which prevented any L2CAP
packet to be received.
Fixed by ceiling the initial credits count in the credits
calculation.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This places a sentinel value at the lowest 4 bytes of a stack
memory region and checks it at various intervals, including when
servicing interrupts or context switching.
This is implemented on all arches except ARC, which supports stack
bounds checking directly in hardware.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Sometime it is observed on the Arduino 101 that when we write more than
4 bytes into TX USB Endpoint, first 4 bytes are getting repeated
(frequency of occurrence ~1/3000).
This patch does following :-
1. In sample application "cdc_acm", it adds capability to
handle partial transfer data incase data is transferred partially
if exceeds maximum data transfer size.
2. It restricts write of more than 4 bytes into TX USB Endpoint.
This is work around to avoid issue occarance.
Jira: ZEP-2074
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When a new UDP or TCP connection handler is to be registered,
we need to check if identical handler has already been created.
If a duplicate is found, the registering call will return -EALREADY.
The earlier code did not check this but allowed two identical
handlers to be created. The latter handler was never called in
this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This helper copies desired amount of data from network packet
buffer info a user provided linear buffer.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
To be consistent with other subsystem menu, use menu for
Bluetooth support in Kconfig instead of menuconfig which
showed up as checkbox.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To allow for hci_uart builds that do not include the controller code,
move the UART Kconfig option used by the sample up one level so that it
is shared by all configurations using Bluetooth:
Jira: ZEP-2132
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 698de88916 ("Bluetooth: controller:
Cleanup redundant ticker busy loop")
Scan enable asserted in ctrl.c line 3756 due to the fact that a
role event was active and ticker job has hence been disabled.
Add back the busy loop so that scan enable can wait until the
active role event completes gracefully.
The ticker busy loop is mandatory in all ticker interface calls
if a blocking behavior is desired.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The calculation in packet_rx_reserve_get() was already handled by
packet_rx_acquired_count_get(). So, let's use that code instead
and remove the duplication.
Change-Id: Ic76f70f1e78bebc74f5bef36cd92a3c332e489e9
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation can be used in packet_rx_reserve_get() where currently
the code is duplicated from packet_rx_acquired_count_get().
Let's allow use of packet_rx_acquired_count_get() regardless of whether
CONFIG_BLUETOOTH_CONTROLLER_DATA_LENGTH is enabled.
Change-Id: I613bde0a407f3caccabb22f369098575965e98ad
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During testing, lr->max_rx_octets and lr->max_tx_octets were
at times set to 0. If we use these 0 values, we end up with
very erratic behavior. Best, to check for a sane value and
if invalid, default to the value in _radio.conn_curr->max_*x_octets.
Change-Id: I57c0e3790d988f0de17993cebe5c5c2ab0fc07a6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When Controller to Host flow control is enabled, output informational
messages for certain operations to help tune and debug the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since the HCI driver debug option applies to both files in
drivers/bluetooth and subsys/bluetooth, the configuration option itself
now lives in the top-level Kconfig file for consistency.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to auto-update Bluetooth PHY to 2Mbps
if the local Controller supports it.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added support for Bluetooth v5.0 PHY Update Procedure in the
Controller.
Asymmetric PHY connections do not work for now due to the
Radio mode not being setup in time in the ISR during tIFS
period and the Radio already ramping up in the cached
previous Radio mode to meet tIFS deadline.
Subsequent commits will add this feature, by either double
buffering the mode in software or using fast radio ramp up
which gives enough time in the ISR to change the mode.
Jira: ZEP-2086
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Scale the ctrl pkt enqueue implementation to allow multiple
ctrl packets to be enqueued. This will aid in the graceful
implementation of parallel control procedure collisions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added HCI macros to check LE Features. Also, added test
macros for 2M and Coded PHY support in HCI Controller.
Earlier a common test macro was used between BR/EDR and LE,
but since LE features do not use pages for feature, an
explicit macro for testing LE feature is added now.
Also, features field in LE device structure is now a single
dimension array of 8 octets.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The APIs for allocating RX buffers were modified recently and hci_raw
had not reflected those changes properly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When we send TCP data segment, we need to set the length
of the application data by calling net_pkt_set_appdatalen().
This is done so that sequence number can be properly
advanced when we receive ACK to that pending packet.
Signed-off-by: xiaorui hu <xiaorui.hu@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The event mask population used to let the Controller know which events
are relevant to the Host needs to take into account the features
supported by the Controller itself, in order to only enable those that
are indeed valid.
Jira: ZEP-2050
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the framework for LE Scan Request Received Event.
The feature is available under the Controller's advanced
features and will be selected implcitly when Bluetooth v5.0
LE Advertising Extensions feature is implemented.
Jira: ZEP-2073
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove unreferenced function hci_evt_is_discardable after
introduction of hci_get_class function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation for refactoring the Controller implementation
into seperate state and role based source files, add Kconfig
options for states and roles in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To guarantee code that is endianness-independent, the sys_le* macros
must be used everywhere when accessing multi-byte values from the
command parameters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In HCI, the response buffer to a command is the same as the one for the
command itself, requiring command parameters to be processed before the
response is formed on the same memory area.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since Controller to Host flow control is a feature that affects both
sides equally, move it to the top-level Kconfig file and consolidate its
use in both Controller and Host.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
