This command will be used to test if model can properly send
segmented and unsegmented messages to a given destination address.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Do not reset net_context information in net_app_close. In case of
TCP behind the curtains connection might wait for some timers to
expire and send some messages (e.g. ACK). If we set source port to
'0', unexpected behaviour might happen with peer connection.
Only reset net_app context related information on net_app_close.
Let net_context_put will take care of proper connection closure.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Right now in FIN_WAIT1 state, if we receive FIN+ACK message, then
tcp state changed to FIN_WAIT2 on ACK flag and immediately on FIN
flag state changed to TIME_WAIT. Then final ACK is prepared and sent
(in queue at-least) to peer. Again immediately state changed to
TCP_CLOSED, where context is freed. net_context_put frees context
and releases tcp connection. Final ACK packet which is in queue
is dropped.
As a side effect of freed ACK packet, peer device keep on sending
FIN+ACK messages (that's why we see a lot of "TCP spurious
retransimission" messages in wireshark). As a result
of context free (respective connection handler also removed), we see
lot of packets dropped at connection input handler and replying with
ICMP error messages (destination unreachable).
To fix this issue, timewait timer support is required. When tcp
connection state changed to TIMEWAIT state, it should wait until
TIMEWAIT_TIMETOUT before changing state to TCP_CLOSED. It's
appropriate to close the tcp connection after timewait timer expiry.
Note: Right now timeout value is constant (250ms). But it should
be 2 * MSL (Maximum segment lifetime).
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
fin_timer will be started after sending FIN to peer. After successful
reception of FIN+ACK message in FIN_WAIT1 state, fin_timer should be
cancelled.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add implementation to consider differing Rx chain delays for
S2 and S8 Coded PHY PDU reception. These changes are
required to meet tIFS timings for transmission after a
reception on S8 coding.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixes many instances of errors similar to below:
zephyr/subsys/bluetooth/controller/ll_sw/ctrl.c:5927:22:
error: declaration of ‘s_link’ shadows a previous
local [-Werror=shadow]
static memq_link_t s_link;
^~~~~~
zephyr/subsys/bluetooth/controller/ll_sw/ctrl.c:5905:21:
note: shadowed declaration is here
static memq_link_t s_link;
^~~~~~
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Consolidate and standardize error handling throughout
lwm2m_obj_firmware_pull.c. As well as handle previously
unhandled errors returned from transfer_request().
NOTE: in general, unhandled errors will now result in
RESULT_UPDATE_FAILED. Previously, unhandled errors in
transfer_request() would result in RESULT_CONNECTION_LOST
which might or might not be over-written with another
result later.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
The CoAP samples use an MBEDTLS config "config-coap.h" which could be
re-used by the LwM2M sample, except that most servers use a larger
maximum content length setting of 1500 bytes.
Let's add a CONFIG to set this for users of the CoAP lib and set the
CONFIG value for the samples to the 256 size currently used.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Currently, LwM2M firmware download only supports coap2http proxy.
Let's add support for coap2coap proxy as well.
This was tested running Californium demo app cf-proxy on the host
machine with the following setting changed in Californum.properties:
MAX_RESOURCE_BODY_SIZE=524288
Add the following to the samples/net/lwm2m_client/prj.conf:
CONFIG_LWM2M_FIRMWARE_UPDATE_PULL_COAP_PROXY_SUPPORT=y
CONFIG_LWM2M_FIRMWARE_UPDATE_PULL_COAP_PROXY_ADDR="coap://[2001:db8::2]:5682"
Build the sample for qemu_x86 as you would normally, but now
you can use a real world coap address to pull firmware using the 5/0/1
resource. The host machine running cf-proxy will pull the remote
resource and then deliver it to the running qemu sample.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
- Add needed settings for DTLS support to the lwm2m_ctx structure.
- Add initialization of MBEDTLS to the LwM2M lib based on the
user application settings in lwm2m_ctx.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
The default net_context remote address is scrambled when using a
connection via DTLS. Instead let's use the dtls context remote.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
While looping through possible lwm2m_ctx matches, we're referencing
remote before checking that the context itself is valid.
Also, reduce indentation issues.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Instead of building under the "app" context, let's build the
LwM2M library as a separate static library. This will be helpful
later when adding support for DTLS as w/o this configuration,
the build breaks on MBEDTLS config includes.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Of the filesystems under subsys/fs/, only the ELM FAT filesystem needs
the disk layer as others (like NFFS) talk directly to the flash API.
This removes the need to define CONFIG_DISK_ERASE_BLOCK_SIZE and
similar which are used by the disk subsystem but not by NFFS.
Signed-off-by: Michael Hope <mlhx@google.com>
This introduces Bluetooth internal API intended to be used for
qualification purposes. Application may register callbacks to get
data that is not exposed by public API.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This will avoid exposing IEEE 802.15.4 Zephyr's L2 private context data
to unrelevant places.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
L2 specific data and IEEE 802154 net mgmt interface are not related.
Plus, application may use the net mgmt part, not the L2 one. So let's
split the content in relevant headers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Content-format is used to determine the type of the PUT/POST
request. Therefore, it's incorrect to assign default when the
caller does not include one in the request.
Define LWM2M_FORMAT_NONE=65535 to indicate the format is missing.
The 65000~65535 is reserved for experiments and should be safe for
the purpose. Check content-type at PUT method to setup
write/write-attrs operation accordingly.
Also, add reporting write-attrs as not implemented to the caller.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
According to LwM2M specification V1_0_1-20170704-A, table 25,
incoming request is a discover op if it is method GET with
accept format as application/link-format
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
According to LwM2M specification 20170208-A, there are two different
discover interfaces supported by the device.
(1) Bootstrap discover (sec 5.2.7.3) (To be implemented)
(2) Device management discover interface (Sec 5.4.2)
- object ID is required (i.e. root directory discover is not allowed)
- attributes should be responded accordingly when implemented
This patch correct the behavior according to the spec and summarized
as follow
(1) Still support CoAP ".well-known/core" but change to report only
first level of the URI.
(2) Respond to caller only when object ID is provided unless it's
bootstrap discover
Fixes#4941
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
IPv6 mcast addr to MAC mcast conversion was factored out to
subsys/net/ip/l2/ethernet.c for reuse by other drivers.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Empty CMakeLists.txt in l2 and l2/ieee802154 deserved to get filled-in
relevantly, instead of centralizing everything in ip/ location.
Also making sure lines don't get over 80 chars.
Also, no need of linking against mbetls unless net shell is enabled.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
https://tools.ietf.org/html/rfc4862#section-5.4.2 :
"""
Before sending a Neighbor Solicitation, an interface MUST join the
all-nodes multicast address and the solicited-node multicast address
of the tentative address.
"""
So, joining should happen before sending DAD packets, and it should
happen for each unicast address added. This is achieved by joining
from net_if_ipv6_addr_add() call. Note that we already leave
solicited-node group from net_if_ipv6_addr_rm(). In particular, we
leave it if DAD fails (as that function is called in this case).
Fixes#5282.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When the controller is connecting to multiple connectable
advertisers, the events are scheduled consecutively avoiding
overlapping events. Calculation of the window offset did not
consider the preparation time before the event, causing the
new master role connection event to overlap with previous
event. This is now fixed by including the preparation time
in the used window offset from the end of connect_ind PDU
transmitted.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed the check related to initiating connection parameter
request procedure. This will avoid sending invalid repeated
dispatch of connection parameter request PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When connection parameter request procedure was responded
by master role with Unsupported Link Layer Parameter Value,
a missing reset of the connection parameter request
procedure state caused next connection parameter request to
be incorrectly responded with same procedure collision
extended reject ind PDU. This caused an eventual connection
disconnection with reason LMP response timeout. This is now
fixed by reseting the state correctly.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If we have the maximum number of supported connections, then it
doesn't make sense to try to do connectable advertising.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Create a slightly smarter algorithm for choosing how long to advertise
each subnet. This is particularly important for the mesh_shell app,
since it uses a 10 second NODE_ID_TIMEOUT, meaning starting Node ID
advertising through user interaction would only succeed in advertising
one subnet (due to this being configured to 10 seconds).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Mesh Profile Specification 1.0 section 7.2.2.2.3:
"When the server starts advertising as a result of user interaction,
the server shall interleave the advertising of each subnet it is a
member of"
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Node ID advertising is short lived, so it's important to make sure
that subnets that get it enabled are first in queue to start
advertising.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We'll soon extend the start functionality with a bit more stuff
(prioritizing the started subnet), so in order to avoid excessive code
duplication, create helpers for these actions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Until now the proxy server code would only advertise with the first
subnet. Introduce tracking of what the last advertised subnet was, and
give each subnet 10 seconds of advertising at a time.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add configuration client model support for NetKey Add message, as well
as a mesh shell command for calling the new API.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The reachable calculation for ND is using fractions combined with
integers and getting rounded to very small results (1ms or 0ms).
Let's split up the fraction into it's numerator and denominator
and perform the math in a better way to get the correct results.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
