Add the necessary PM hooks like Low Power state entry
count and residencies for logging and debugging purposes.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
The bluetooth controller has been using the flag '-Ofast' to keep
within a real-time limit. There are two problems with this; firstly,
when a project should be optimized for size it is standard to use -O2,
not -Ofast.
Secondly, optimization flags have been deemed to be non-portable, so
instead of directly using "-Ofast" we should use the intent-macro
OPTIMIZE_FOR_SPEED_FLAG to ensure toolchain portability.
Testing has shown that we are still within the real-time limit when
changing from -Ofast to -O2. -Ofast is about 1us and 1% faster, but
increases the code size by 13kB (5% of the available flash on a
nRF51).
Since the slowdown is comparatively small compared to the code size
increase we have decided to use -O2 in place of -Ofast.
Other optimization combinations were also measured and their results
can be seen below:
-Ofast in BLE Controller and in #pragma in entropy driver.
Memory region Used Size Region Size %age Used
FLASH: 138920 B 256 KB 52.99%
[bt] [INF] encode_control: l: 6, 6, 7; t: 75, 45, 132.
-O2 in BLE Controller and in #pragma in entropy driver.
Memory region Used Size Region Size %age Used
FLASH: 125840 B 256 KB 48.00%
[bt] [INF] encode_control: l: 6, 6, 7; t: 75, 51, 133
-O3 in BLE Controller and in #pragma in entropy driver.
Memory region Used Size Region Size %age Used
FLASH: 138920 B 256 KB 52.99%
[bt] [INF] encode_control: l: 6, 6, 7; t: 75, 50, 132.
No extra CFLAGS for BLE and entropy driver (pragmas removed), using
CONFIG_SIZE_OPTIMIZATIONS=y
Memory region Used Size Region Size %age Used
FLASH: 120124 B 256 KB 45.82%
[bt] [ERR] isr_rx_conn: assert: '!radio_is_ready()' failed
No extra CFLAGS for BLE and entropy driver (pragmas removed), using
CONFIG_SPEED_OPTIMIZATIONS=y
Memory region Used Size Region Size %age Used
FLASH: 138004 B 256 KB 52.64%
[bt] [INF] encode_control: l: 6, 6, 7; t: 61, 51, 130.
NB: RAM usage differences were insignificant.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
If we receive an IPv4 that has broadcast destination address, then
properly handle it.
This means that for
* ICMPv4, if CONFIG_NET_ICMPV4_ACCEPT_BROADCAST is set (this is the
default value) and we receive echo-request then accept the packet.
Drop other ICMPv4 packets.
* TCP, drop the packet
* UDP, accept the packet if the destination address is the broadcast
address 255.255.255.255 or the subnet broadcast address.
Drop the packet if the packets broadcast address is not in our
configured subnet.
In sending side, make sure that we do not route broadcast address
IPv4 packets back to us. Also set Ethernet MAC destination address
properly if destination IPv4 address is broadcast one.
Fixes#10780
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add utility function that returns true if given IPv4 address is
a broadcast address. This will be used in later commits to check
received packet IPv4 source and destination addresses.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove extra ntohl() calls when checking IPv4 address against
a subnet address.
Convert also the IPv4 address to be const as the netmask related
functions do not change its value.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Cache the used transport protocol in net_pkt. This way we can
avoid traversing IP header to get the last protocol in network
packet. This is mostly an issue in IPv6 which can have a long
list of extension headers after IPv6 header and before the
transport protocol header.
Fixes#10853
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previously, the wifi shell needed to remove the quotes from the
SSID parameter, passed in by the underlying shell.
The new shell is now able to parse quoted strings as arguments,
so this adjustment can be removed.
Otherwise, it results in a failure to connect to an AP, as the first
character of the SSID name is stripped off.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Connection complete event with error code can be received only for
central role and can be compiled conditionally.
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Wrong Kconfig template was used for max debug level which caused
the max level to be the default level (ERROR). This prevented
all debug prints from showing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds a possibility to reject incomming LE Connection request
due to insufficient authorization or encryption key size.
This is needed for qualification purposes
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This adds support for returning various return codes from
the channel accept callback.
This is needed for implementation of incoming connection
authorization for certification purposes.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Rename connection response results to map those that are defined
for BR.
BR: BT_L2CAP_BR_*
LE: BT_L2CAP_LE_*
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
log_strdup writes out of bounds of a strdup slab.
e.g: CONFIG_LOG_STRDUP_MAX_STRING=46 and
LOG_STRBUF_STR_SIZE=47 then in the line L:529
sdupl[LOG_STRBUF_STR_SIZE - 1] = '\0';
writes out of bounds because the available buffer space
is only 44 bytes (rounded up to 48 bytes and minus 4 bytes
for the allocated flag).
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
When user was typing a new command and next pressed an up arrow
shell has displayed previously executed command. Next it was not
possible to display back currently edited command using a down arrow.
Fixes#10766.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The net_buf log level Kconfig setting was using template from
networking, which might not be available for Bluetooth code.
This caused the log level to be ignored.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The maximum log level was using wrong template which caused
the max value to be ignored.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Extended logger to support optional log message prepending with
function name.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended supported number of arguments in log message. Support for
messages consisting of more than 2 chunks had to be added. So far
messages could consist of one chunk (up to 3 args) or two chunks
(2 args in first chunk and 7 in second chunk). Once 2+ chunks
support is added number of arguments is techinically limited to
15 (4 bit field). log_core and log_output extended to suppor 10
arguments.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The CONFIG_NET_DEFAULT_LOG_LEVEL template entry was only partially
fixed earlier and some spaces were not there around "=".
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Current TLS socket implementation assumed that PSK ID stored in
credential manager is NULL terminated. It's actually better to store
only the string content, as the string length is stored as well. This
approach is less confusing, when a user is not operating on C strings
but on a non-NULL terminated byte array.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When DBG level for CONFIG_LWM2M_LOG_LEVEL is disabled, a compiler
warning is generated:
In file included from include/logging/log.h:11:0,
from subsys/net/lib/lwm2m/lwm2m_engine.c:28:
subsys/net/lib/lwm2m/lwm2m_engine.c: In function ‘engine_add_observer’:
subsys/net/lib/lwm2m/lwm2m_engine.c:558:3: warning: implicit
declaration of function ‘sprint_token’
[-Wimplicit-function-declaration]
sprint_token(token, tkl), lwm2m_sprint_ip_addr(addr));
^
Let's remove the #if guards around sprint_token() and let
the Linker remove it when not needed.
Signed-off-by: Michael Scott <mike@foundries.io>
It is possible that connect callback is called when shell is not
yet set. Make sure to check this and fallback to use printk() if
shell_printf() cannot be used.
Fixes#10617
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The connect command parameters were not checked properly if
user decided to supply only mandatory parameters.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the device does not support wifi offloading, then return -ENOTSUP
so that wifi support can be enabled for testing purposes even if
the actual device does not have wifi support. This is happens for
example in qemu which does not support wifi offloading.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that we define and declare the _net_app_register() and
_net_app_unregister() functions properly if net_app logging level
is set to debug.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Convert the monitor protocol to a proper logger backend. This also
means that our log.h headerfile gets greatly simplified.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that log processing happens in a separate thread, the
BT_STACK_EXTRA macro is not needed (since there's no significant
overhead), and therefore the BT_STACK macros become unnecessary as
well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use irq_lock (same way as bt_hex does it) and increase the number of
static buffers to reduce the risk of reuse before a buffer gets
processed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
1. Changed return value of function: shell_cmd_precheck from bool to
int. Now it returns:
0 when argument count is correct and help print is not requested
1 when help was requested and printed
-EINVAL on wrong arguments count
This change simply shell_cmd_precheck usege in command handlers.
2. Unified all commands in shell_cmd.c file.
3. Fixed a bug where help was not printed on wrong argument count.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
This shell command was tied to bluetooth and the bluetooth shell and
also had messages all related to nordic ICs.
Make it generic and put it under drivers/flash/ so it can be included by
anyone and independently of bluetooth.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add 2 new flags to control the output of newlines by the logger output
module. By default the logger adds both CR and LF, and with these 2 new
flags it is now possible to request LF only or no newlines at all.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
