In order to improve readability, rename TCP_FIN_WAIT
states into TCP_FIN_WAIT_1, TCP_FIN_WAIT_2.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This patch adds the selection of the necessary CONFIG_*
options for allowing the use of privacy on VEGA platform
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
The radio on the VEGA platform will now be able to resolve Resolvable
Private Addresses through the use of the CAUv3 hardware. With this
patch the RPA feature is now fully supported on the Controller:
RPA addresses are generated with local IRK and resolved with
previously exchanged peer IRK.
Signed-off-by: Jeanina Dragusin <ancajeanina.dragusin@nxp.com>
When disconnecting att_reset is called and all requests are notified
but instead of passing req->user_data like it should it pass the req
itself which nowdays comes from a k_mem_slab, rather than being a
contiguous memory that would contain the request and its user data,
which would likely cause invalid access.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add shell options to configure an extended advertiser for directed
advertising.
Add shell options to provide arbitrary advertising data as well as
giving scan response data.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This patch introduces two major changes to the directed advertising
feature of the bluetooth host.
Deprecating the bt_conn_create_slave_le, and removing
bt_conn_le_create_slave which has never been released. This behaviour
has now been moved by to providing the peer direct address into the
advertising parameters.
Introducing directed advertising support for nonconnectable
directed extended advertising, both scannable and non-scannable.
A bug was also fixed in the the directed-adv command in the shell
when the argument "low" was given. The advertiseng parameter pointer
declared with BT_LE_ADV_CONN_DIR_LOW_DUTY was declared in a scope that
was no longer valid when it was used to start the advertiser.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Makes a common link_closed function for PB-GATT, getting rid of a bug
where cb_data is reset before the link closed callback. Also ensures
that the link close and reset order is the same in both scenarios.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the hardware identifier obtained with the hwinfo API is stored
in the correct order based on the platform, there is no longer the need
to reverse its bytes when populating the serial number in the
corresponding USB descriptor.
Fixes#24103
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The LE Connection Complete HCI event, unlike its Enhanced counterpart,
only uses 0x0 and 0x1 for Peer Address Type. Fix it so that it reflects
the specification correctly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fill the mTimestamp filed in OpenThread frame based on the net_pkt
timestamp value (only if NET_PKT_TIMESTAMP is enabled).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This change is to allow access to the firmware block context in order to
give the firmware update callback implementation an indication of when
to reset the flash context. Additionally, it allows for a validity check
between the total expected size downloaded and the actual size
downloaded. A simple implementation can check if the block context's
current downloaded blocks is equal to the expected block size in order
to determine if the flash context needs to be reset. This approach
seemed the simplest, and knowing the firmware block context can have
other purposes. This has been tested by accessing the block context
during the update in the block received callback and confirming that the
callback had information regarding the current downloaded bytes.
Fixes#16122
Signed-off-by: Kyle Sun <yaomon18@yahoo.com>
Received frames shall be handled in the OpenThread thread, not in
the receiver thread.
Passed received frame to the function that will handle it in a proper
thread instead of calling otPlatRadioReceiveDone directly.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
OpenThread received frame handling shall be done in the OpenThread
thread.
Created API to pass net packets to the proper thread and handle them
there.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
The time parameter cannot be K_NO_DELAY because the time delay
parameter is ms so using value 0 instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_context API will change, the s32_t timeout parameter
will be changed to k_timeout_t. All the Zephyr users of this API will
be changed in subsequent commits. This is internal Zephyr API only,
so the API is not deprecated etc.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Mention in websocket API documentation that the timeout value
is in milliseconds. Check timeout values properly using K_TIMEOUT_EQ()
macro.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use k_timeout_t internally, no change to user API.
Clarify the documentation of the timeout parameter that it is
in milliseconds.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use 64-bit time in order to avoid overlaps, and do not use K_MSEC()
as that will convert to k_timeout_t which we do not want in this
case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This PR fixes#23482. The preamble size for a 2M phy was incorrect.
There is a bug in calculation of time for the DLE procedure:
the preamble size is incorrect for the 2M phy
Fixes#23482
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
When PB-GATT Procedure timeout, func `bt_mesh_pb_gatt_close`
will also dumplicated with `link_closed()`
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Check the return value of LE Set Extended Advertising Parameters
command when starting an advertiser from bt_le_adv_start with
CONFIG_BT_EXT_ADV enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
The LE Set Extended Advertising Set Random Address command may be
issued at any time after an advertising set identified by
the Advertising Handle parameter has been created using the
LE Set Extended Advertising Parameters command.
This commit fixes the advertising set issueing the set random address
command before the advertising set is created in the controller.
Since the le_adv_set_random_addr function has is used to get the the
own address parameter for the it could not simply be moved, and
moving the own address parameter handling out of this function
would create a potentioal maintaince problem.
Also this function is used for both with and without advertising
extension feature so changing it is not trivial without breaking all
the previous random address handling already put in place.
The simplest solution was therefore to postpone the command until the
parameters has been set using 2 flags.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use bluetooth assert on HCI command send error since this assertion is
always enabled and we should not continue after this has failed.
Log command status failure with information in order to make it more
visible as the HCI status code is more interesting than the -EIO error
code returned by the function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add BT_ASSERT_MSG assert mechanism that can print assertion messages
when verbose bluetooth asserts are enabled.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
