Add API to set the scan parameters used in the LE Create Connection
HCI command used by bt_conn_create_le and bt_conn_create_aute_le.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add support for the new scan options and use the LE Extended Scan
HCI commands if they are available in the controller.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Refactor scan and initiator random address handling to a helper function
so that it can be re-used.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add reference count old to new value transition in the debug print, this
makes it easier to interpret the printed line when debuggin reference
count bugs.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extract setting advertising filter policy parameter from the adv params
options field to a helper function.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use the scan types defined in bluetooth.h instead of the hci defined
ones. Although they have the same value it is best to avoid using the
hci.h header in applications.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Update buffer sizes needed when advertising extensions is enabled. Since
BT_RX_BUF_LEN is used for the HCI command as well we need to fit the
full 255 bytes of the Set Extended Advertising Data or Scan Response
Data plus the 3 byte header of an HCI command.
For the discardable buffer size we need to fit the LE Extended
Advertising Report event, which can be a maximum of 255 bytes plus the
2 byte header of an HCI event.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add Kconfig options to enable extendend advertising and scanning
support.
Include option to support both types of advertising
commands in case the controller capabilities is not know or the
controller is pluggable.
Include option to only support legacy advertising API, this is to
support the use-case of advertising using different identity than the
scanner or initiator.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate BT_LE_ADV defines in hci.h that are expected to be used by the
application in the scan received callback to identify the advertising
PDU type. These defines are mixing HCI input parameters and advertising
PDU types. Internally it is acceptable to mix these, but at the API we
should to mix in them.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Rename filter_dup parameters used for scanning filter options to the
more generic name options, and make scan filter options follow same
naming patters as advertising and initiator scan options.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Deprecate bt_create_conn_le and rename it to in order to add return
code, new arguments and to follow the established naming convention.
Add API for the application to control the scan parameters of the
initiator role. This allows the application more scheduling control
of the initiator in multi-role scenarios. Also provides options to
configure the initiator for LE Coded PHY for long range support.
We deprecate the old way of creating connection to make the name more
consistent with the rest of the API.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Identify when received PUBLISH message is malformed and overall packet
length received is smaller than parsed variable header lenght.
Add unit test to cover this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Verify more strictly that data read from the transport fits into RX
buffer. Switch to unsigned integers, where possible, to prevent
unnecessary signed/unsigned operations.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The standard allows up to 4 bytes of packet length data, while current
implementation parsed up to 5 bytes.
Add additional unit test, which verifies that error is reported in case
of invalid packet length.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
With the introduction of ZephyrConfig.cmake all parts of CMake code
should rely on the CMake ZEPHYR_BASE variable instead of the environment
setting.
This ensures that after the first CMake invocation, then all subsequent
invocation in same build folder will use same zephyr base.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Such state needs to be set _from_ the PM API functions and not the other
way round. So if a network device driver does not support such API, it
will not be able to set the core net_if on PM state, obviously.
Currently, these functions only set/unset NET_IF_SUSPENDED flag.
More logic will be added later, to decide whether the net_if can be
actually set to suspend mode or not and also to take care of all timers
related to the interface.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This function can be used for example by network power management
to check if the network interface can be suspended or not.
If there are network packets in transmit queue, then the network
interface cannot be suspended yet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We need to know whether the net_pkt was successfully placed
to transmit queue. It is possible in TX side, that the net_pkt
is already in TX queue when for example TCP packet is
re-transmitted, in which case the queue submit will fail.
This cannot happen in RX side as there are no timers involved.
It is required to check about such pending flag before trying to submit
it into the queue. Indeed, the work queue could be scheduled right after
such queuing, thus checking for the pending flag afterwards would
provide a false information.
It is unfortunate k_work_submit_to_queue() does not return anything as
it would simplify the code then.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
By changing the various *NET_DEVICE* macros. It is up to the device
drivers to either set a proper PM function or, if not supported or PM
disabled, to use device_pm_control_nop relevantly.
All existing macro calls are updated. Since no PM support was added so
far, device_pm_control_nop is used as the default everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Minor optimization to use a local variable instead of a
deferencing of a struct member.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is a new init level SMP that was just added, and this module needs
to take it into account.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix so that different isochronous synchronization modes can be used.
It filters out the synchronization mode before sending the endpoint
type to drivers.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
Update the ticks_current value on last stopped ticker
instance, so that when a new ticker instance is started
the anchor ticks calculation uses the correct current tick
with respect to supplied anchor ticks.
Fixes#23805.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit renames the `cortex_r` directory under the AArch32 to
`cortex_a_r`, in preparation for the AArch32 Cortex-A support.
The rationale for this renaming is that the Cortex-A and Cortex-R share
the same base design and the difference between them, other than the
MPU vs. MMU, is minimal.
Since most of the architecture port code and configurations will be
shared between the Cortex-A and Cortex-R architectures, it is
advantageous to have them together in the same directory.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Sleep mode 1 is supposed to be a low-latency sleep mode where devices
are left in active mode. Thus we should only bring devices to low-power
when in sleep mode 2 in sys_pm_policy_low_power_devices().
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
In case OPENTHREAD_NCP option is disabled, uart.c platform driver should
not be compiled as it misses dependencies.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
When NCP starts-up some of the initialisation functions of a regular
OpenThread device do not need to be called, because they get triggered
by wpantund via UART. Instead NCP initialisation needs to be called.
A small typo has been fixed as well.
Also initialisation for raw link packet interface has been added. Can be
used for picking up 802.15.4 frames and interpreting them in the
application.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
The functions ppp_mgmt_raise_carrier_on/off_event() were not
implemented, but already documeted in the header net/ppp.h
Fixes#23420
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
The commit reduces default MCUMGR buffer size and introduces changes to
mcumgr that fix problem with mcumgr not being able to download file off
the Zephyr running device.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Remove use of k_cpu_idle in controller, and refactor the
implementation used to start, wait and stop clocks needed
by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Fix directed advertising from privacy disabled peer. In this case we
need to have the local IRK in the controllers resolving list in order to
have the controller resolve the initiator address of the directed
advertising pdu (ADV_DIR_IND).
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Fix directed advertiser using the wrong local IRK when doing directed
advertising when the identity of the advertiser is not the default
identity.
This is only an issue for the directed advertiser because it is only
for the directed advertiser that we use the controllers local IRK
to generate the Advertisers RPA.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Add header definition for bt_read_static_addr function. Declaring it
without a header definition will not give any compilation error when
function definition changes.
Refactor nRF SoC specific code into nRF specific source files and
provide weak definitions when these are not implemented. This will make
it easier to add handlers per vendor.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
To complete the removal of the ext/ folder, move the ctf_map.h file to
where it really belongs, which is subsys/tracing/ctf.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When using BT_LE_ADV_NCONN_NAME then the advertising name will not be
included in the advertising data. This is because the host always puts
the device name in the scan response. But since the scan data was
otherwise empty the advertising type was set to ADV_NONCONN_IND.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Splits PB-ADV and PB-GATT into separate modules with a common interface
to modularize prov.c.
Additional trivial fixes from testing:
- Reduces warnings for normal occurances like repeated packets.
- Makes link ack a non-reliable packet to prevent it from being repeated
until prov invite.
- Provisioner does not send link fail, but closes the link (as per spec
section 5.4.4). This prevents lingering zombie links on both sides.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Allocates segmented message buffers as slabs in a common pool for RX and
TX. This reduces memory requirements for both TX and RX, as TX messages
can be stored without the network and advertising buffer overhead, and
RX can use only the slabs it needs, instead of allocating a full size
segmented message. This approach also removes the need for decrypting
the segments for each retransmission, reducing overall processing load.
Slab based segmentation for tx also introduces queuing of segmented
messages, which allows the application layer to send multiple messages
to the same destination without violating Bluetooth Mesh specification
v1.0.1, section 3.6.4.1. This mechanism is provided through a flag that
blocks segmented messages to a destination which a message is already
being sent to until the previous message finishes.
This changes the SDU size configuration to a symmetrical
RX_SEG_MAX/TX_SEG_MAX pair of configurations, plus a new segment pool
side configuration. It also removes the binding between the TX_SEG_MAX
config and the advertising buffers, reducing the minimum advertising
buffer count from 6 to 3.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
The Friend queue uses the message SeqAuth to determine whether the
message is already in the queue. To facilitate this, the SeqAuth is
passed around as a pointer throughout the transport modules. In the
bt_mesh_ctl_send functions, this parameter is also exposed in the API,
but the internal usage is inconsistent and buggy. Also, no one actually
uses this parameter.
- Removes seq_auth param from bt_mesh_ctl_send, instead passing NULL
directly to the friend module, to enforce its addition to the queue.
- Makes the seq_auth pointer const throughout the friend module.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
