Some backends use DMA. Usually, DMA doesn't work correctly, when memory
to transfer is cached. Add a config to place the common buffers in the
nocache section.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add support for SPI host command backend for STM32 chips family.
Unfortunately, the current SPI API can't be used to handle the host
commands communication. The main issues are unknown command size sent
by the host(the SPI transaction sends/receives specific number of bytes)
and need to constant sending status byte(the SPI module is enabled and
disabled per transaction). Thus the SPI backend includes basic SPI STM32
driver adjusted to host command specification.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add a config to save the final result of a last host command that has
sent EC_HOST_CMD_IN_PROGRESS response. To get the final result use the
ec_host_cmd_send_in_progress_status function.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add a native way to log Host Command communication.
Use Zephyr logging system to do it. Use debug and normal levels.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add a config to decide if a new dedicated thread for Host Command is
created during initialization.
If not, the ec_host_cmd_task has to be called by another thread to
handle host commands.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add a separate config to enable autoinitialization of the host command
subsystem, called by the chosen backend.
It allows setting the chosen backend without autoinit.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Add a new backend for Host Commands that uses UART. The backend bases
asynchronous UART API.
The UART backend is mainly used by FPMCU.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Rework the Host Command support. It includes:
-change API to backend
-change a way of defining rx and tx buffers
-fix synchronization between the handler and backend layer
-simplify the HC handler
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Follow naming pattern in the subsystems(logging or shell) and name
the layer between generic handler and peripheral driver "backend".
The name doesn't suit that well to the SHI backend, because there isn't
SHI API itself and the SHI interface is used only for the host
communication. So the backend code includes the peripheral driver itself.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
The Host Commands can be used with different transport layers e.g. SHI
or eSPI. The code that provides the peripheral API and allows sending
and receiving Host Commands via different transport layers is not
actually drivers of a peripheral, so move it to the
subsys/mgmt/ec_host_cmd folder.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
This commit adds the support for host commands being transported
by the Serial Host Interface on the NPCX SoC.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
This commit increases the stack size for thread handling the host
commands requests. It was required due to the stack being
corrupted using earlier default size. The thread priority is now
configurable using the Kconfig.
It also adds alignment to the tx_buffer since the npcx MCU requires it
to work correctly and removes clearing the buffer before use due to
the hard time requirements. Tests checking if buffers are cleared
are also removed.
Signed-off-by: Michał Barnaś <mb@semihalf.com>
Add a generic host command handler framework that allows users to
declare new host command handlers with the HOST_COMMAND_HANDLER macro
at build time. The framework will handle incoming messages from the
host command peripheral device and forwards the incoming data to the
appropriate host command handler, which is looked up by id.
The framework will also send the response from the handler back to the
host command peripheral device. The device handles sending the data on
the physical bus.
This type of host command communication is typically done on an embedded
controller for a notebook or computer. The host would be the main
application processor (aka AP, CPU, SoC).
Signed-off-by: Jett Rink <jettrink@google.com>
