MPS shall never be bigger than MTU + 2 as the remaining bytes cannot
be used since the SDU is limited to length + MTU.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Add implementation to support Coded PHY update procedure
with packet transmit time restrictions.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Use S8 coding Rx chain delay timings to calculate the PA
pin assertions when in Coded PHY.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Always use S8 Rx Chain Delay instead of the actual Rx-ed
packet coding. I believe, as the packet always start with
S8, hence S8 timings when used the tIFS is near correct
value.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When calculating and setting up the header compelte timeout
use S8 coding Rx chain delay.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In the commit dd52b8ea02 ("Bluetooth: controller: Fix
first connection interval timing"), instead of using just a
tick unit as workaround, microseconds corresponding to a
tick unit was used while calculating the window offset to be
used at the connection update instant. This introduced an
error in scheduling the first event with new connection
parameters, causing supervision timeout of connection update
procedure.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Mesh Profile Specification v1.0, 4.4.1.2.8:
"When an element receives a Config Model Subscription Add message
or a Config Model Subscription Virtual Address Add message that
is not successfully processed (i.e., it results in an error condition
listed in Table 4.113), it shall respond with the Config Model
Subscription Status message, setting its fields to the values
of the corresponding fields (i.e., the identically named fields)
of the incoming message and setting the Status field to a status code
(defined in Table 4.113), and setting all other fields to 0."
The same applies to other Model Subscription messages.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's possible that tx_notify still contains items when a Disconnect
Complete happens. Since the normal path for processing tx_notify is
not taken when the connection is not in CONNECTED state, we must make
sure to process the list latest in conn_cleanup() that's called as one
last thing before the connection object is freed up.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fixed a missing reset of FC feature on HCI reset. This
feature provided a simple connection handle based event
exclusions, but this is no longer needed with the
support for controller to host flow control. This feature
should be removed in the future.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
A connection might have gotten disconnected by the time that an ACL
buffer is free up, in which case there is no need to send a HCI
command for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a peer master performed a PHY update procedure with no
change, the state machine was not released. This blocked
any future local initiation of the procedure and also
leading to termination of connection with reason LMP
response timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fixed the usage of NRF_AAR peripheral for controller privacy
to clear events on configure and on every radio ISR entry.
Without this fix, there was spurious AAR matches leading to
controller asserts.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
PHY Update procedure timeout was started without transition
to the state that waits for the procedure to complete. This
prevented the timeout from being reset on successful
completion of the procedure and eventually leading to a
connection termination with reason LMP Response Timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix Connection Parameter Request Procedure's Connection
Update Procedure initiation to calculate the offset rather
than selecting offsets from an out-of-bound memory area.
The symptoms of the bug was noticed as a supervision timeout
due to use of incorrect offset communicated to peer and a
wrong offset used in scheduling the connection events.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When the peer slave rejects a Connection Parameter Request
Procedure, the controller proceeds to perform a Connection
Update Procedure without clearing the procedure timer that
causes the connection to terminate eventually. This is
fixed by clearing the procedure timeout when the Connection
Update Procedure completes.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
If a peer master role has support for Connection Parameter
Request Procedure set in its supported features but would
send an Extended Reject Ind as response to the procedure
then the controller incorrectly initiated a Connection
Update Procedure which is not permitted in a slave role.
This would lead to connection timeout after the used instant
in the invalid Connection Update Procedure.
This is fixed by initiating a Connection Update Procedure
only if in a master role.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Since the Zephyr HCI VS extensions apply to both the Host (using them
for additional functionality) and the Controller (implement the commands
and events), it make sense to make this a common setting in order for it
to be configurable in a way that applies to both.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The PA/LNA feature is not functional on nRF51x series due to added
interrupt latency. Disable this feature unconditionally for those ICs to
avoid unexpected behavior.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Issuing HCI reset command while having connections sometimes
hung the controller.
ll_reset supplied invalid stop ticker id to role_disable
when trying to stop all connections. Connection role does
not utilize stop ticker. The invalid ticker id supplied
referenced memory outside the pool of tickers and based on
what the content is in RAM there, the controller would hang
trying to stop connections.
Fixed by not calling the ticker_stop interface with invalid
ticker ids.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Proxy configuration messages are allowed (in fact required) to use
unassigned addresses, so they should be exempt from this check.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The test failure may be e.g. because of an unknown company id, and in
that case the spec expects us to ignore the message.
With this patch it should be possible to pass MESH/SR/HM/RFS/BI-01-C.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
A previous patch which moved dispatching the health publish callback
to a later moment introduced a regression where the period divider
does not get updated when it should. In fact, having the divider as
part of the Health Server context is redundant, since the same
information is already stored generically in the model publication
context. Switching to using the model publication context makes things
simpler and ensures that the value is always up-to-date.
With this patch it is possible to pass MESH/SR/HM/CFS/BV-02-C.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We should ignore invalid addresses (helps pass
MESH/NODE/CFG/LPNPT/BI-01-C). Also fix a copy-paste issue in an error
log.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The values all need to be zeroed when heartbeat subscription is
disabled. This makes it possible to pass MESH/NODE/CFG/HBS/BV-01-C.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Implement the Read Build Information VS command. This returns a UTF-8
encoded string, which is extendable by the user via a new Kconfig
option.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the Zephyr VS command that allows a Host to write a public
Bluetooth Address to the Controller in order to allow Hosts to provide
their own public Bluetooth addresses.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
From section 3.4.5.3 in the Mesh Profile Specification 1.0:
"A node shall implement a Local Network Interface."
Removing the Kconfig option also helps clean up quite a lot of code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_mesh_net_relay() function needs to allow TTL <= 1 for the local
network interface since that's the code path that locally originated
outgoing packets take.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Mesh Profile Specification v1.0, 5.3.3:
"On the PB-ADV bearer, when the receiver has received all segments of
a transaction, the receiver shall calculate the FCS for the received
Provisioning PDU, and if it matches the FCS field in the Transaction
Start PDU, it shall send a Transaction Acknowledgment PDU after
a random delay between 20 and 50 milliseconds."
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Mesh specification recommends defaulting to the company ID in the
composition data when no other ID is relevant (e.g. in error cases or
if the app has not provided a callback).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Encrypting and sending a message takes a considerable amount of time
which makes the publication period longer than expected.
With this patch it is possible to pass MESH/SR/HM/CFS/BV-02-C test.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The branch for handling the case when the app has not provided a
callback for health faults was encoding the payload in a wrong way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
To avoid signedness issues with some compilers, like icx, use 'char *'
instead of 'unsigned char *' for the at_client buffer.
Fixes#3600
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The code was passing the wrong first parameter to the sdu_len_is_ok()
function.
Fixes#3985Fixes#3984
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
