This commit will take back changes made by previous commit
i.e. fad8ff39c3.
This is beacause k_sleep() based delay is not behaving as
expected while testing & take more time than expected.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
The disco_l475_iot1 has the Inventek eS-WiFi, so lets enable the sample
on the board. (This also gets us something that will build test the
eS-Wifi driver as part of sanitycheck).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds common option to disable support for LE Data Length Update
procedure in controller and host.
This will reduce flash usage by compiling out le_data_len_change
event handler that will never be called if controller has been
compiled with BT_CTLR_DATA_LENGTH option disabled.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
This adds common option to disable support for PHY Update
procedure in controller and host.
This will reduce flash usage by compiling out le_phy_update_complete
event handler that will never be called if controller has been
compiled with BT_CTLR_PHY option disabled.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Since setting USB console port name is moved to DTS users have
problems enabling it. Notify user that the console is not set.
Fixes#10693
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Adds the virtualcom device to the nrf52840 SoC dts and adds a board
specific nrf52840_overlay.dts file, copied exactly from the
arduino101_overlay.dts file, to set the console device name
appropriately for the subsys/usb/console sample project.
There were no clear alternatives to add a usb_cdc: virtualcom device to
all known SoC devices with USB support as should probably happen.
There was also no clear alternatives to add a non-board specific overlay
to the example.
This fixes a specific problem with the nrf52840-dk board for this sample
project.
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
With this commit now it is simple to understand flow of logic when
NODE receives any message & how it proceed things one by one.
Plus NODE will immediately send GET status to Client instead of
waiting for things which has less priority.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
In order to prevent failing tests on i.MX RT the following samples were
limited to a minimum 140k of flash: http_client, http_server,
socket/echo_client and sockets/echo_server.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add IMX IPM sample application. It reads the data sent to the
Messaging Unit and sends them back. It has been tested on Udoo Neo Full
board with the Cortex-A9 core running Linux and sending the data
into the Messaging Unit A and the Cortex-M4 running this sample Zephyr
application and reading the data from Messaging Unit B and sending it
back for Linux side to read it from Messaging Unit A.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Rename existing headers and sybols to mqtt_legacy, to allow new
implementation to keep old config and header names.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The show_sensors_data() function tries to access val[2] when
outputting the Z-axis value, so the array must have at least three
elements. This also triggered Coverity CID 189741.
Fixes#11482
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This comparison was always supposed to be > rather than >=. Fixing
this also fixes Coverity CID 189740.
Fixes#11483
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Let's expand the sanity build testing for the lwm2m_client by
doing the following:
- Add variant builds for DTLS, bluetooth and modem
- Check various combinations of hardware across each of these
variant builds: frdm_k64f, nrf52_pca10040, nrf52840_pca10056,
disco_l475_iot1
Signed-off-by: Michael Scott <mike@foundries.io>
When the WNC-14A2A modem binding was originally introduced, I thought
the base_label would shorten the define keeping the result short and
easily portable. Turns out with the latest changes, it has a side
effect of removing the "DT_*" prefix which is breaking the build.
Let's remove "base_label" from the modem binding and adjust all of
the dts_fixups referring to the WNC14A2A defines.
NOTE: This commit moves the left-over WNC14A2A dts_fixup defines from
the nRF52 soc into samples/net/lwm2m_client as the new values.
They will stay there until the modem can be re-configured as a shield.
Signed-off-by: Michael Scott <mike@foundries.io>
During the modem overlay move from the K64F board directory to the
LwM2M sample code, 2 DTS entries were dropped:
current-speed = <115200>;
status = "ok";
Without these entries the DTS defines for UART2 and CURRENT_SPEED
are missing from the generated_dts_board.h file.
Signed-off-by: Michael Scott <mike@foundries.io>
All drivers require DTS for their primary SPI settings.
Removing SPI_[0-9]_NAME config option added some more samples changes.
Usage of these options there was anyway not relevant.
Fixes#11064
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We have cases with UART drivers where TX interrupt handling is not
bootstrapped properly on enabling them. To make such cases more
obvious, start this sample with console_write(), the output of which
wouldn't appear if that's the case. (Of course, the sample starts
with printk() exlaining what may happpen.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the
nrf52840_pca10056 board and should be maintained and configured
outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
echo_server can use up to 6 sockets therefore it needs more file
descriptors than the maximum default value specified.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
There are a small handful of samples that still utilize <board.h>
include, to minimize the use of <board.h> to these specific cases and
allow us to remove adding the board dir to the top level include search
path, we explicitly in each sample add the specific board dir it needs.
For the microbit cases these could be replaced by DTS support in the
future when the pwm_nrf5_sw supports DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now states which are bound have single timer that means
means for lightness variation there is one timer & for
temperature variation there is one timer.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Corrected mapping of message handler for Generic
Move Set, Generic Move Set Unack, Light CTL Set &
Light CTL Set Unack.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Removed extra blank line. Add new
bound_states_transition_type_reassignment() function in
transition.c to improve code readability & understanding.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
This edition would improve by default mesh network
performance. This is after testing with nRFMesh app
from Nordic Semiconductor.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Include regex pattern matching of console output
to determine the sample execution status.
Add fixture to determine the hardware dependency
if any. If FRAM is connected to board externally,
then with fixture, automation would be able to
identify the board with sensor to trigger the
execution.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
Regex pattern matching is included to match the
execution log from console to return test result
in automation.
Also add fixture to identify the external sensor
connected for automation framework to trigger test
cases on particular board which is connected with
required sensor.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
This commit would add the pull-up or pull-down on the switch pin and
makes it functional on the board where there is no external pull-up.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can help find unused symbols. Those end up without a type if
'default' is used instead of 'def_bool', which generates a warning.
Search for "Kconfig.defconfig" in
https://docs.zephyrproject.org/latest/application/kconfig-tips.html for
a longer explanation.
Keep the 'def_bool' for the following symbols, which seem to be
deliberately defined only in Kconfig.defconfig files:
- ALTERA_AVALON_I2C
- ALTERA_AVALON_MSGDMA
- ALTERA_AVALON_PIO
- ALTERA_AVALON_QSPI
- ALTERA_AVALON_SYSID
- CLOCK_CONTROL_IMX_CCM
- CPU_EM4_DMIPS
- CPU_EM4_FPUDA
- CPU_EM4_FPUS
- FP_FPU_DA
- I2C_GECKO
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Change the sample to use a different controller device name per pin. We
shouldn't assume that on a given board that all the pins we are using
will be on the same GPIO controller device.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a dts binding for the Atmel WINC1500 WIFI chip. Update the
quark_se_c1000_devboard to utilize this binding as well as the wifi
sample app.
We now get all the GPIOs related to the Atmel WINC1500 from the device
tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
All labels containing "_<8-hex-digits>_" or "16550_<3or6-hex-digits>_"
in their names, assumed to be generated by the extracting script,
are updated with the DT_ prefix, to reflect the recent changes made
to the script.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
If shell UART backend was enabled and logger uart backend was
not explicitly disabled then both were used resulting in logs
being printed twice on terminal.
Patch modifies default state of log uart backend to depend on
state of shell uart backend.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
