Migrate the whole pm subsystem to use new power states information
from power_state.h and get states and residency properties from
device tree.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add EDAC shell application demonstrating EDAC API usage. Can be used
for verification of the functionality with error injection mechanism.
Sample is also included in the twister tests.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Provide a demonstration of using the timeutil skew infrastructure to
measure the relative error of the two clock sources on Nordic boards.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Remove UP Squared support for the gpio sample that was merged after
the sample itself was removed.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Due to the routing, the ip_k66f board can only use RTT to export
console. With this change the SHELL is enabled to get access
to network commands (like ping).
To use it with RTT from Segger:
-------------------------------
On HOST (terminal 1):
./JLink_V664/JLinkRTTLogger -Device MK66FN2M0XXX18 -RTTChannel 1 \
-if SWD -Speed 4000 ~/rtt.log
On HOST (terminal 2):
nc localhost 19021
(19021 is the port number for the Segger RTT server)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'local-mac-address' nodes are helpful for assessing if the LLDP like
example of DSA switch works correctly.
As those are used only for testing (or when user explicitly needs them),
those are added as DTS overlay to DSA example.
The 'local-mac-address' properties will be visible when one assess the
LLDP response from ip_k66f board (each LAN port has different IP
assigned).
Example output from 'tcpdump -v -i eth0':
-----------------------------------------
Chassis ID TLV (1), length 7
Subtype MAC address (4): 00:00:12:13:00:37 (oui Unknown)
Port ID TLV (2), length 7
Subtype MAC address (3): 00:00:12:13:00:37 (oui Unknown)
Time to Live TLV (3), length 2: TTL 120s
System Name TLV (5), length 13: ip_k66f LAN:3
End TLV (0), length 0
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch brings simple example on per DSA port LLDP filtering based on
MAC address of received packet.
Each lan1, lan2 and lan3 ports handle separately LLDP packets going into
them.
Nonetheless, the K66F ENET handles correctly all other packets types -
to be more specific - ICMP, TCP/IP.
Setup -> ON HOST:
Configure/start the lldpd daemon (debian 10) on host to use
MAC 01:80:c2:00:00:03:
(lldpd -ddd & ) && sleep 2 && \
lldpcli configure lldp agent-type nearest-non-tpmr-bridge
Signed-off-by: Lukasz Majewski <lukma@denx.de>
CoAP protocol defines registry of Content-Format option values.
This patch adds this enumeration to coap header file to make it
available to all applications using CoAP protocol. It modifies
code using CoAP service to use new enumeration.
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
This patch modifies Bluetooth HCI RPMsg drivers and samples to use
RPMsg Service instead of configuring OpenAMP directly in the driver
or the sample.
Co-authored-by: Piotr Szkotak <piotr.szkotak@nordicsemi.no>
Signed-off-by: Hubert Miś <hubert.mis@nordicsemi.no>
'main' function should retun 'int' and not 'void'. Otherwise
some picky compilers (like ARC MWDT) would warn about that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Introduce retransmission counter to the coap_pending structure. This
allows to simplify the retransmission logic and allows to keep track of
the number of remaining retranmissions.
Additionally, extend the `coap_pending_init()` function with `retries`
parameter, which allows to set the retransmission count individually for
each confirmable transaction.
Fixes#28117
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
DW16 provides information on mechanisms to enter and exit 4-Byte
address modes, returning the device to reset state, and how to
manipulate the values in the first status register.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW15 provides information on entry and exit from QSPI modes. In
particular, it specifies whether and how the status register must be
updated for this feature.
Add a JESD216 devicetree property for the Quad Enable Requirements
value.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Modify led_pwm sample in order to make it usable in device testing:
- Remove parenthesis from the logs as they prevent use of regex
- Add a harness_config multiline regex in order to enable verdict
generation
- Update README
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Currently the following shields will thus be supported
waveshare_epaper_gdeh0154a07
waveshare_epaper_gdeh0213b1
waveshare_epaper_gdeh0213b72
waveshare_epaper_gdeh029a1
Signed-off-by: Kim Bøndergaard <kim@fam-boendergaard.dk>
Signed-off-by: Kim Bøndergaard <kibo@prevas.dk>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Since the additional objects are only added for compilation, enable
them in sample.yaml instead, so that they get built by the CI. Remove
them from the actual sample, as they obfuscate the sample purpose and
the objects visible from the server perspective.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
BLE and LwM2M grew in terms of RAM usage so that the sample does not
fit into nRF52832 anymore in the default configuration. This cause
twister to report an error when overflows errors are enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The IPSP example code is explicitly registering the all local-link nodes
address (ff02::1). This is currently already registered by the normal
IPv6 stack at interface initialization, so doing it in the application
is redundant.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
This sample is trying to register four multicast addesses:
uart:~$ net iface
...
IPv6 multicast addresses (max 8):
ff02::1
ff02::1:ff01:c41e
ff02::1:ff00:1
ff02::1
Increasing CONFIG_NET_IF_MCAST_IPV6_ADDR_COUNT to 4 to make neighbor
discovery work correctly.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Currently Zephyr links reset-vector.S twice in xtensa builds:
into the bootloader and the main image. It is run at the end
of the boot loader execution and immediately after that again
in the beginning of the main code. This patch adds a
configuration option to select whether to link the file to the
bootloader or to the application. The default is to the
application, as needed e.g. for QEMU, SOF links it to the
bootloader like in native builds.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Conditionally use either DPPI or PPI channel in the sample so that
it can be built for all nRF SoCs. Update documentation accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert the driver so that it creates its instance basing on DT.
Remove no longer needed Kconfig option CRYPTO_NRF_ECB_NAME.
Also update accordingly the crypto sample.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Mark the CANopen sample with program download support as build-only
since it depends on MCUboot being flashed to the board prior to the
generated application firmware image.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Tigerlake H has less RAM and fewer cores. Both should be
supported, selectable at the board level. For now use the H
configuration as more readily available for testing.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
1. SOF doesn't have to be built in .bin format
2. don't include soc.c and soc_mp.c twice in cmake
3. remove an unused mailbox.h header
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
CAN_MCP2515_MAX_FILTER is not needed anymore and was probably just a
misunderstanding. Aligned it with the other CAN drivers.
This also was the last difference in the mcp2515 specific config for the
can sample, so that can be deleted as well.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
