Set integration_platforms on these samples to just mps2_an385.
This should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set integration_platforms on these samples to a single platform, we
prefer native_posix, than a qemu platform mps2_an385 and finally a
hardware platform.
For the 'basic' sample we use native_posix, for the 'rtt' we use
frdm_k64f ad we need a hardware platform that supports 'rtt', and for
the 'usermode' we utilize 'mps2_an385' as we can run in QEMU.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set integration_platforms on these samples to just mps2_an385.
This should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set integration_platforms on these samples to just native_posix. This
should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
All dma drivers are devicetree based now so we can remove the last
bits of Kconfig associated with the old driver style.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace device_get_binding with DEVICE_DT_GET for getting access
to the io-channels/adc controller device.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set integration_platforms on these samples to just frdm_k64f.
This should be sufficient to make sure these tests build.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I only see one sample with an overlay using the now legacy sda-pin and
scl-pin properties. Move it to the new style.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Modify an example by adding command that is using shell_getopt funtion.
Extent sample.yaml with getopt configuration.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add an example callback implementation that prints out the new maximum
payload given the updated datarate.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
The default shell configuration has heavy flash and memory requirements,
requiring project maintainers to set many configuration options to "n"
to keep flash and memory requirements within reason.
This adds a new configuration option, CONFIG_SHELL_MINIMAL, which will
disable flash and memory heavy options by default, and allow project
maintainers to select/imply only the options they want.
On a quick test from an ARM board I'm working on, enabling this option
cut flash space requirements by ~8 KB, and memory requirements by ~1 KB.
Signed-off-by: Jack Rosenthal <jrosenth@chromium.org>
Set integration_platforms on these samples to just native_posix.
This should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set integration_platforms on these samples to just native_posix. This
should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add an application that uses Direction Finding API for
transmission of CTE in connectionless mode (periodic adverising PDUs).
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
We need to set a proper IPv4 netmask to each VLAN interface
so that IPv4 source address selection will work properly.
If we do not do this, then the network interface could be
selected incorrectly for the VLAN interfaces which could then
mean that the packet might get dropped by the target device.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adjust the documentation and devicetree overlays so the sample can be
built for any board with an Arduino I2C and SPI pinout, defaulting I2C
and SPI to y to make it easier to switch between the two without
requiring a pristine build.
The user has to choose an appropriate overlay or have a sensor built
in to the board.
Use the newly introduced DEVICE_DT_GET_ANY() in main.c to ask for a
bosch,bme280 without worrying over the details or exposing
DT_DRV_COMPAT-based functionality that is really meant for drivers.
Remove the no-longer-needed board specific overlay for nRF52840 DK;
this is covered by the generic Arduino overlays now.
Fix the datasheet link while we're here.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Now that we have consolidated tf-m signing, the combined
binary is always named tfm_merged, so we need to modify
the QEMU targets in the tfm-integration samples.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Place the new signing code in the TFM module CMakeLists.txt.
Make some small tweaks and add a sentence to the docs.
In the process, make a few changes to the signing code:
- Change some names of files created.
- Minimize the number of files created.
- Use hex files instead of bin files. This is so we don't need to know
the offset when creating hex files from bin files.
Also add signing for MCUBOOT_IMAGE_NUMBER=1 based on the code from the
v2m_musca_b1 board, though, this board does not build with =1 now
because of (I assume) some flash aliasing which places the S and NS
images 0x10000000 apart, where the manual algorithm places them next to
each other. It builds with =2, though.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
Set integration_platforms on these samples to just native_posix. This
should be sufficient to make sure these tests build and run.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A different configuration is applied when running this test
using west or using twister.
Both will use the disco_l475_iot1 overlay, but the extra config
for clock bus tunning is applied only when using twister and
samples is failed when run with west.
Move this extra config from sample.yaml to board .conf file so
it is applied in both cases.
Fixes#32376
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
There was some code to demonstrate the cpu_mask API here, but it was
asymmetric (only thread B was pinned) and assumed exactly two CPUs.
Start both threads pinned to CPUs 0 and 1 from an external main, and
predicate the pinning on there actually being more than one SMP CPU.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Add an object to retain data across both reboots and entry to
SYSTEM_OFF. This only works on nRF52, since nRF51 and nRF53 require
different low-level operations to configure RAM retention.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample application to test MAX6675 cold-junction-compensated
K-thermocouple to digital converter.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enable PECI and KSCAN drivers to evaluate any side-effect
in LPM entry/exit and power consumption.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Remove support for the Musca-A board. This board is rarely used, few
are available and superceded by Musca-B and Musca-S.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update sample espi driver test to exercise some SAF functionality
based on the limited hardware available. Note the SAF test will
erase a section of the flash. SAF tests are enabled for the EVB only.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Introduce a dts board overlay on the nucleo_l053r8 board as this
board was used for testing addition of resolution setting on the
mcp9808 sensor driver.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
This commit adds the nRF IEEE 802.15.4 Service Layer Fault Handler
to the 802154_rpmsg sample.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
