Add infineon XMC4 series UART support. Driver supports
only poll mode using XMCLib.
Out of 4 available UART's on SoC, only UART1 is confgired
by default in UART mode until GPIO & pinctrl support.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Add infineon xmc series with XMC4500 support. XMC series comes with,
- CPU operates upto 120MHz
- 3 RAM (PSRAM1 - code, DSRAM1 - data and DSRAM2 - communiation)
- upto 1MB flash
init: clock control & gpio is not done, so SoC initialization directly
relies on HAL. Core operating clock is stored in no_init section, which
is kept under DSRAM1. Only DSRAM1 is used until clock support. Using
PSRAM1 and DSRAM1 needs adaptation in linker script - planned for next
revision.
Note: SystemInit cannot be consumed directly due to vector table +
HAL linker dependency.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
For HPET devices, configure it with fixed delivery mode because HPET
timer interrupt is needed to fuel the scheduler for all CPUS.
For all other type of devices, like UART, I2C, GPIO, Ethernet, etc.
configure them as lowest priority delivery mode, in which IO APIC
delivers the interrupt to the processor core that is executing at the
lowest priority among all the processors listed in the specified
destination. In this case, the device drivers can avoid the trouble of
handling repeated interrupts delivered to all CPUS.
Signed-off-by: Zide Chen <zide.chen@intel.com>
The label property does not need to have its type set
explicitly to string, so remove it.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
By this commit USB audio class implementation is introduced
to Zephyr.
The Zephyr USB audio device class follows bellow
documentations:
- Universal Serial Bus specification rev2.0 (usb20.pdf)
- Universal Serial Bus Device Class Definition for Audio Devices
(audio10.pdf)
- Universal Serial Bus Device Class Definition for Audio Data Formats
(frmts10.pdf)
- Universal Serial Bus Device Class Definition for Terminal Types
(termt10.pdf)
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit adds support for nRF52820 development on nRF52833DK.
Changes afffects:
- Introduce files related to board description.
- Add blank documentation file (for future update).
- configuration files for build process.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
This commit adds basic support for nRF52820 SoC.
Changes affect introducing:
- architecuture files (dtsi)
- configuration of nrfx drivers
- adaptation of inclusions based on chosen SoC
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add STM32F427. This is mainly aimed towards the stm32f427vi.
Changes:
- Add stm32f427 support based on previous work
done for the stm32f429.
- Rework currunt stm32f429 implimentation to now
be based on stm32f427.
- Introduce dedicated dtsi for the VI variant of both
stm32f427 and stm32f429. This is done to prevent stm32f4.dtsi
from being included twice.
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Update dtsi and pinmux macros for stm32f7 family. Add sdmmc1 to dts file
for stm32f746g_disco. Also add board specific configuration file for
fat_fs sample.
Signed-off-by: Helge Juul <helge@fastmail.com>
Update the dtsi for stm32l471 (which the higher SoCs are based on) to
support the stm32-sdmmc disk access device. Enable the device for the
stm32l496g_disco board, and update the pinmuxing.
Note that the stm32l496g_disco board also has a card detect gpio
(MFX_GPIO8), but this is not supported yet. When not specified the
driver will assume a card is present.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add a disk access driver for the stm32 sdmmc component. The driver is
based around the stm32 cube HAL and uses the blocking API.
Signed-off-by: Anthony Brandon <anthony@amarulasolutions.com>
Add initial support for Broadcom Viper SoC.
It has ARM Cortex-M7 and Cortex-A72 cores.
Signed-off-by: Arjun Jyothi <arjun.jyothi@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Add initial support for Decawave DW1000
IEEE 802.15.4-2011 UWB transceiver.
Driver has basic functionality. Additional functions such
as reading out timestamps and delayed TX were implemented
for test purposes, but also require support in the 802154
subsystem.
Register, sub-register, and defaults defines in the file
ieee802154_dw1000_regs.h are taken from the Decawave's
DW1000 driver for the Mynewt OS.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Binding used for LPC random number generator hardware.
Describes RNG device node in LPC5xxx SoCs device tree peripherals.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add support for ADC on H7 series. Note that ADC1 and ADC2 share the same
register set, so it is added as "adc1_2".
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Convert i2s_sam_ssc driver to utilize devicetree. We replace Kconfig
options for specifying the DMA configuration (channel, DMA device name)
with getting that from devicetree. We also get pincfg from devicetree,
however we still have Kconfig sybmols to specify if the RF or RK pin is
enabled.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sam_xdmac driver to utilize devicetree. As part of the
controller binding we specify that dmas should contain a channel and the
perid for the DMA transaction.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The DS3231 is an I2C real-time clock with internal temperature
compensated oscillator, maintaining civil time to 1 s precision with
nominal 2 ppm accuracy from 0-40 Cel.
The basic functionality is exposed as a counter that is always running
at 1 Hz. Much more functionality is exposed as driver-specific API,
including the ability to translate between the time scale of the DS3231
and the time scale of the Zephyr uptime clock. This allows correlation
of events in the system clock to UTC, TAI, or whatever time scale is
used to maintain the DS3231.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add a driver that can handle several instances of AT45 family chips,
which are enabled by specifying DT nodes for them with the "compatible"
property set to "atmel,at45" and other required properties like JEDEC
ID, chip capacity, block and page size etc. configured accordingly.
The driver is only capable of using "power of 2" binary page sizes in
those chips and at initialization configures them to work in that mode
(unless it is already done).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This header is physically related to the Adafruit Feather, but uses a
different pin numbering and exposes a slightly different set of pins.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Once the TPM driver and the required configs have been added,
now this patch enables the usage of the PWM framework on KW41Z
SoCs. As such, the DTS gets the proper nodes and the pinmuxing
is done according to the configuration requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
The TPM (Timer/PWM Module) is a 2- to 8-channel timer which supports
input capture, output compare, and the generation of PWM signals to
control electric motor and power management applications.
This patch adds the driver and the binding necessary for instantiating
the driver. The work is based on the RV32M1 driver for TPM done by
Henrik Brix Andersen. A later patch will enable this driver to be used
for the KW41Z SoC, if PWM support is requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
* Define USB driver for base stm32wb device.
* Enable USB for the nucleo_wb55rg board.
* Properly initialize USB power + clock for the platform.
Signed-off-by: Pete Johanson <peter@peterjohanson.com>
This patch introduces the periph to/from memory dma transfer
using the dmamux feature and define new values
for dma cells on client side
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Atmel SAM D5x and E5x series SoCs include the ARM memory protection
unit that supports up to 8 memory regions.
This commit adds the missing device tree MPU node to `samd5x.dtsi`,
which is used by both the SAM D5x and E5x series SoCs.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This patch is defining the DMA1 & 2 for the sm32l4 series
with 7 channels and support of mem2mem transfers
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This includes the dma cells as client for the spi
An example of the client part is defined in the dma.yaml
Consequently, bindings for the dmas property becomes then 'not required'
Including dma.yaml is not needed as dma properties
are now part of base.yaml
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add device tree nodes for the Digital-to-Analog (DAC) modules present
in the NXP Kinetis K6x series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add device tree node for the Digital-to-Analog (DAC32) module present
in the NXP Kinetis KE1xF series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add initial devicetree for the NXP LPC55S16. Only non-secure (ns)
access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Rework the atom/linker.ld to match how ia32/linker.ld works with regards
to how PHYS_LOAD_ADDR & PHYS_RAM_ADDR are set based on CONFIG_XIP and
from which DT_PHYS_{RAM,LOAD}_ADDR defines. We update the minnowboard
dts and atom.dtsi files to keep in sync with this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks from devicetree.
We add a property ('calib-offset') for the SAM{D,E}5x family of SoCs
that is the bit position offset from ADC0 BIASCOMP in the NVM Software
Calibration Area Mapping. For ADC0 this is typically 0 and for ADC1
this will be 14.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In STM32 can driver CAN2 instance need to know the base address
of CAN1 instance which is referenced as master can.
Add this information as an optional property to stm32 can binding.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
