This patch implements BMM150 driver with polling mode and its tested
with original BMM150 sensor hardware. Driver works on I2C
interface as of now.
Following datasheet is taken as reference while developing driver.
http://www.mouser.com/ds/2/783/BST-BMM150-DS001-01-786480.pdf
Signed-off-by: Punit Vara <punit.vara@intel.com>
nrf SOC uses nrf rtc timer (not sys tick), which is 32kHz,
whereas CPU runs at higher speed (nrf52 runs at 64MHz).
So 32Khz is too slow to measure critical kernel parameters.
This patch does :-
1. Add support for nrf SOC for timing_info benchmarking.
2. Uses SOC timer to measure kernel parameters.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
The API/Variable names in timing_info looks very speicific to
platform (like systick etc), whereas these variabled are used
across platforms (nrf/arm/quark).
So this patch :-
1. changing API/Variable names to generic one.
2. Creating some of Macros whose implimentation is platform
depenent.
Jira: ZEP-2314
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
The stack address was incorrectly specified when stack usage
was being debugged. This caused compiler to emit this warning
drivers/ieee802154/ieee802154_cc2520.c:1136:16: warning:
dereferencing type-punned pointer will break strict-aliasing
rules [-Wstrict-aliasing]
((struct cc2520_context *)(&__device_cc2520))->
^
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the interrupt isn't acknowledged, the callback will continue to be
called.
Jira: ZEP-2556
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Masks for level- and edge-triggering levels are 0, so the following
check will be always true:
if ((flags & GPIO_INT_ACTIVE_LOW) == GPIO_INT_ACTIVE_LOW)
Invert the evaluation order, by checking the masks that are not 0
first.
Jira: ZEP-2557
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The compilation of the i2c_ll_stm32 fails when we
enable the interrupt mode. The struct i2c_stm32_data
is needed to initialize the semaphore. This patch adds
the missing struct for interrupt mode.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
When transmitting to the UART interface using polled mode, the ESP32
driver would return 0 regardless of the success state. Return the
character that has been transmitted to comply with the API.
Jira: ZEP-2552
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Esp-idf defines the BIT macro that is also defined in Zephyr's
misc/util.h. Fix the issue by including the esp-idf headers first, so
that a check in util.h won't redefine the macro if it's already
defined.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This exposes the CCM operations through generic Crypto API.
Change-Id: I09346e77bf8821c208305a7aa2805cf49cb42d71
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
'pad' parameter controls whether crc16() should add padding at the end
of input bytes or not. This allows to compute CRC16 for data stored in
non-contiguous buffers where CRC value is calculated using subsequent
calls to crc16() with padding added only for last chunk.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
data_addr is not guaranteed to be word-aligned so we need to read it in
a safe way, otherwise this can trigger hardfault on nRF51.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add _i2c_map_dt_bitrate() that maps from a bitrate to the I2C zephyr
cfg bit fields used in i2c_configure().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some targets (e.g. STM32-based boards) only have SPI drivers using the
new API. To support both these and existing, legacy SPI drivers in the
SPI HCI driver, abstract out the SPI API into shim routines.
There are no behavioral differences due to this patch. The next patch
will add support for the new API.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Per ZEP-1958, Phase 2 of adding CC3220sf LaunchXL support,
was to "deprecate the CC3200 launchxl support in Zephyr
(redundant to the CC3220)."
Effectively, the CC3220 SOC replaces the CC3200.
This patch removes the following:
* the imported CC3200 SDK
* CC3200 SOC, board, DTS files.
* adjusts other files where cc3200 was mentioned.
Also, it fixes explicit references to CC3200 in generic
CC32xx driver files.
Jira: ZEP-1958
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
ll_radio_state_is_idle() returns bool, not an error value - this means
it is non-zero on success.
Jira: ZEP-2445
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Rename the BT_CONTROLLER prefix used in all of the Kconfig variables
related to the Bluetooth controller to BT_CTLR.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add support for TICKLESS KERNEL in nrf_rtc_timer for Nordic family of
processors. This patch includes :-
1. Programming RTC based on "next timer" value from timeout queue while
A. exiting idle_exit.
B. on RTC interrupt.
2. Impliments some of functions which will be required by sys_clock and
scheduler.
ZEP-1819
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
This patch fixes the read operation of the I2C driver
for all the receptions (1-byte, 2-bytes, N-bytes when
N > 2)
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Tested-by: Yannis Damigos <giannis.damigos@gmail.com>
Tested-by: Martin Iñaki Malerba <inakimmalerba@gmail.com>
In interrupt mode, the drivers entered a forever loop if the
I2C_MSG_RESTART flag was set. This patch fix this issue.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The EVENT interrupt is generated when:
– SB = 1
– ADDR = 1
– ADD10= 1
– BTF = 1 with no TxE or RxNE event
– TxE event to 1 if Buffer interrupt enabled
– RxNE event to 1 if Buffer interrupt enabled
We need to disable and enable the Buffer TxE and RxNE interrupt
inside the EVENT ISR. The LL_I2C_{Enable,Disable}IT_TX and
LL_I2C_{Enable,Disable}IT_RX functions, used now, enable and
disable both Buffer and Event interrupt. This patch uses the
LL_I2C_EnableIT_BUF and LL_I2C_DisableIT_BUF functions to
enable and disable the Buffer interrupt (TxE, RxNE).
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
* add nested interrupt support for interrupts
+ use a varibale exc_nest_count to trace nest interrupt and exception
+ regular interrupts can be nested by regular interrupts and fast
interrupts
+ fast interrupt's priority is the highest, cannot be nested
* remove the firq stack and exception stack
+ remove the coressponding kconfig option
+ all interrupts (normal and fast) and exceptions will be handled
in the same stack (_interrupt stack)
+ the pros are, smaller memory footprint (no firq stack), simpler
stack management, simpler codes, etc.. The cons are, possible
10-15 instructions overhead for the case where fast irq nests
regular irq
* add the case of ARC in test/kernel/gen_isr_table
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Now that we have an mcux shim driver, remove the old k64-specific
driver. Also remove include/drivers/k20_sim.h, since the old
k64-specific driver was the only thing left using it.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds a shim layer around the mcux ftm driver to adapt it to the Zephyr
pwm interface.
Jira: ZEP-2025
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The random number generator from ESP32 uses noise from Wi-Fi and
Bluetooth radios. If these are off, a pseudo-random number is
generated instead; this is currently the case, but even though it's a
black box, it's arguably better than returning a timestamp as a
pseudo-random number generator.
According to the ESP32 Technical Reference manual, the RNG passed the
Dieharder Random Number Test suite (version 3.31.1)[1], but nothing has
been said about the quality of the PRNG.
The RNG register is read directly; no effort is made to use its
contents to feed an entropy pool in a way that's similar to /dev/random
on POSIX systems, as no such subsystem exists on Zephyr at the moment.
[1] http://webhome.phy.duke.edu/~rgb/General/dieharder.php
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Zephyr's watchdog API is badly designed in the sense that it's a 1:1
abstraction on top of whatever Quark D2000 expects for its watchdog,
instead of expecting a generic timeout value.
This implementation tries as much as possible to calculate the watchdog
timeout in a way that's compatible with a Quark D2000 running at 32MHz;
a comment in adjust_timeout() explains this in more detail.
Jira: ZEP-2296
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This provides basic GPIO support, with interrupts, and the ability to
read and write to ports on a pin-by-pin basis.
Jira: ZEP-2286
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
This implements a driver for the pin multiplexer as present in the ESP32
SoCs.
All APIs are supported.
Jira: ZEP-2297
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The alignment went off because of the move to use internal fixed-size
integer types (instead of standard int types).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It used to be that there was a fairly empty "Bluetooth Drivers" menu
entry in the drivers menu. This entry was present even though there
was no drivers/bluetooth code being compiled in.
With this patch "Bluetooth Drivers" will no longer be present when
BT_CONTROLLER is enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The CONFIG_BT_WAIT_NOP define is used only by
zephyr/subsys/bluetooth/host/hci_core.c.
It is also the only config in drivers/bluetooth that is in use when
BT_CONTROLLER is enabled. Moving it into the bluetooth subsystem
allows us to restructure the drivers/kconfig code such that the entire
Bluetooth driver menu option is omitted when the BT_CONTROLLER is
enabled.
Moving it will also mean that all configs in drivers/bluetooth will
now be related to configuring the source code in drivers/bluetooth.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Added function helps setting the longest possible rx and tx buffers for
single SPI transfer. Each of these buffers is a continuous memory
region. It is useful for example when peripheral supports easyDMA.
Signed-off-by: Michał Kruszewski <michal.kruszewski@nordicsemi.no>
The API name space for Bluetooth is bt_* and BT_* so it makes sense to
align the Kconfig name space with this. The additional benefit is that
this also makes the names shorter. It is also in line with what Linux
uses for Bluetooth Kconfig entries.
Some Bluetooth-related Networking Kconfig defines are renamed as well
in order to be consistent, such as NET_L2_BLUETOOTH.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are two kinds of HCI implementations. Bluetooth drivers in
drivers/bluetooth that implement HCI by using a wired serial
transport layer to talk to an external controller chip. And a
bluetooth controller in subsys/bluetooth/controller that directly
talks to an internal on-chip controller node.
Currently, when the the subsys/bluetooth/controller is used there
still exists exposed to the user a bluetooth driver configuration
menu, even though no external bluetooth driver is in use. This is due
to a dependency on certain configs in driver/bluetooth that are needed
even though no external controller is used.
This patch moves one of these configs, BLUETOOTH_HCI_RESERVE, from
drivers/bluetooth/hci/Kconfig to subsys/bluetooth/host/Kconfig such
that eventually we can omit the entire Bluetooth driver menu option.
This re-organization does not change when the config can be enabled.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
