Fix issues with tab vs space as well as missing license/copyright
header in hci/Kconfig.
Change-Id: Id766308dc8eda2d598ea749e5e0d2166014db929
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_driver API was created when Zephyr only had a Bluetooth host
stack, but no controller-side functionality. The only "driver" that
was needed for the host was the HCI driver, and hence "HCI" was
omitted from the name.
With support both for host and controller Zephyr will be getting more
Bluetooth driver types, in particular radio drivers. To prepare for
this, move all HCI drivers to drivers/bluetooth/hci/ and rename the
bt_driver API bt_hci_driver.
Change-Id: I82829da80aa61f26c2bb2005380f1e88d069ac7d
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since RSSI events trigger interrupts and signal the RX path
semaphore with a resulting event lenght of 0. Due to this
fact the Controller HCI driver was leaking (i.e. not freeing)
those events, grinding the recv_fiber to a halt.
Issue identified by Szymon Janc.
Change-Id: I3e259b2823717b523ac331f8f787252414fb9290
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Report the HCI version supported by the Controller as 4.2,
since it was set as 0 (1.0b) and this confused certain Host
implementations, such as BlueZ.
Change-Id: I809721ee9c2b55e77e6a3ca63688c802a9ffa0ba
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The grove sensors use the sensor interface, so make them depend
on it just like the other sensors.
Change-Id: I9b62a3fa26f54dd683c65ca154c1af7c7c92772f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Set DMA transfer to QM_DMA_TYPE_SINGLE for all channels.
This keeps the previous behavior as of QMSI 1.1.
In the future, we may consider adding support for using other DMA
transfer types. This, however, will demand adding new API to Zephyr's
dma.h .
Change-Id: I8071555190662a72279069ff9fce3d4b9e861629
Signed-off-by: Maciej Kuc <maciejx.kuc@intel.com>
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
STM32F4 requires the alternative function config to be set, so just
initialize that as part of the gpio configure call.
Change-Id: I33a4a8efec59c5ebe7dc3f3580f0dd2bf7ded7f4
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Adds basic sensor driver support for the NXP FXOS8700 6-axis
accelerometer/magnetometer. Currently this driver supports
accelerometer-only, magnetometer-only, and hybrid (accelerometer +
magnetometer) modes, as well as 2g, 4g, and 8g accelerometer full scale
ranges.
This driver does not yet support any sensor triggers such as the data
ready trigger, or runtime changing of sensor attributes.
Datasheet:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Origin: Original
Jira: ZEP-721
Change-Id: Iff0f751c737196f60d5c5d3448631b57093ece34
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Change-Id: I6e3c7e4e420d9b9c55bbb49cf6f13b6e09ec4bb7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Correct the text of the SYS_CLOCK_TICKS_PER_SEC #error diagnostic to
reflect the actual logic of the gate.
Change-Id: I28ad324b0b246e4a8de29b64483a97577a1b6fb7
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The config variable WDT_0_IRQ_PRI is intended to be generic across a
range of watchdog drivers, however it has no default value which means
that if CONFIG_WATCHDOG is enabled, but no driver is provided for a
specific board the the configuration will fail. For now, make
WDT_0_IRQ_PRI depend on the only driver that uses it.
Change-Id: I54708d66ac8fbc2ef657a1ef4510eb5e7a2cff28
Signed-off-by: Marcus Shawcroft <marcus.shawcroft@arm.com>
The Ready To Send (RTS) hardware flow control signal in the nRF5
UART was being configured as an output with a pull-up on it.
This was seemingly causing certain issues with btattach on Linux
and it's not done anywhere else.
Change-Id: Id792d967b043ea7a796d6598500a733c092dbc2c
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
