The SPI API allows waiters to block until SPI I/O has completed. The
asynchronous subset of the API allows waiters to learn a status value
for the result of the I/O. However, the synchronous API does not allow
this.
Due to this limitation, synchronous API users cannot learn when
interrupt-driven I/O fails, which precludes proper error handling.
Resolve this limitation by adding a sync_status field to struct
spi_context, and using it to return operation results to the waiter.
Since there is only one status field, reduce the maximum number of
supported waiters from UINT_MAX to 1. This is not a problem for
current users, which all wait with the entire context locked.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Void pointer arithmetic is undefined behavior (UB).
It's OK for struct spi_buf to contain a void *, because those values
are only ever stored, read, and compared. However, pointer arithmetic
is done on the tx_buf and rx_buf fields in struct spi_context, so
those need to be u8_t * to avoid UB.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Add SPI pin mux tables for 96b_carbon. Note that SPI1 is for
internal use on the board connecting to the 96b_carbon_nrf51, while
SPI2 is broken out to an expansion header.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The ESP32 UART driver can only be used on the ESP32 SoC AFAICT. But it
did not have a depend clause so it was polluting the options of other
platforms.
With this patch the ESP32 driver will no longer be exposed to users of
non-ESP32 devices.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch implements following functionality in polling mode.
Ambient light
RGB light
proximity sensor
Following datasheet has been used to develop driver
https://docs.broadcom.com/docs/AV02-4191EN
Jira: ZEP-1552
Signed-off-by: Punit Vara <punit.vara@intel.com>
Fix clock polarity and phase configuration by using correct
bit shifted configuration values.
Also, fixed SPIM1 config struct initialization that referred
to wrong SPI0 value.
Signed-off-by: Nathan Loretan <nathan.loretan@nordicsemi.no>
As SLIP TAP is now the default after the commit ca0ad13a61
("net: enable SLIP only on QEMU targets"), clarify the comments
and settings in various Kconfig files that talk about slip.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Move to using the generated IRQ defines from the DTS instead of soc.h.
This change also fixes a minor bug in that the error irq priority wasn't
getting correctly picked up from device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch allows the use of the MCR20A driver with KW2xD devices.
The clock output of the transceiver can be used as an input clock
for the PLL of the SoC. The hardware reset and CLK_OUT setup of
the transceiver should then be performed during the initialization
of the SoC. The driver is not allowed to do it again.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some patches have been lost during rebase before the initial commit,
this path fixes it.
- correct copyright in registers definition header file
- fix undefined macro inside CLK_OUT configuration
- use the return value of k_sem_take if there is a timeout
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Following rework of pinmux driver for whole stm32 family,
remove call to stm32_get_pin_config which is no more
used.
Include dt-bindings stm32-pinctrl.h file to ensure coherency
between dts files and pinmux driver.
Due to change of "port" from enum to a series of define
(enum not accepted as dt binding), rework gpio_stm32_config
declaration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F3 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32F4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed as information is transfered to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework stm32f1 pinmux code for future dts based pinmux code
generation.
Pin configuration is now done directly thanks to gpio port
configuration. Reference to pseudo alternate functions are
now removed same as the use of pins[] array.
Pins function (uart tx for instance) is set implicitly by
defining gpio mode and configuration.
This behavior is specific to stm32f10x series.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
STM32L4 pinmux handler is reworked to support future pinmux dts
generation.
Preliminary change is done to move pin configuration
informations in a {pin, conf} structure closer to dts fields
"pins" array is removed and information is transferred to
"pinconf" array
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The ethernet HAL has a different uint32_t typedef than Zephyr's u32_t:
uint32_t in the HAL is long unsigned int, while in Zephyr it's
unsigned int. This is causing a build warning on GCC ("warning:
passing argument 2 of ‘ENET_GetRxFrameSize’ from incompatible pointer
type") when passing a u32_t* where ENET_GetRxFrameSize expects a
uint32_t*.
Add a cast to silence the warning.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
The net_stack_analyze function wants to look at the stack buffer,
but it is making assumptions on where this data is that are no
longer valid. Change to use the proper APIs for referencing this.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
patch fix the dead code issue reported by coverity static scan
for gpio driver of cc2650 TI SOC. GPIO_DS_DFLT_LOW macro
is defined Zero, bitwise and with any value would result to
zero,because of which only false condition of if is evaluated
but not the true condition.This is a fix for jira ZEP-2355.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux adc16 driver to adapt it to the Zephyr
adc interface.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds common and Kinetis-specific adc device tree properties, and updates
all Kinetis SoC and board dts files to include adc nodes.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Kconfig assumed that there would only ever be one instance of an
adc, but some Kinetis devices have multiple adc instances.
Jira: ZEP-1396
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
As I2C_0 (port 0) isn't used on the STM32 platforms we didn't exclude
the related Kconfig options if DTS was enabled. However other SoCs
(like NXP) do use I2C_0 so we need to fixup the Kconfig dependencies
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch uses chosen property zephyr,bt-uart, zephyr,uart-pipe
and zephyr,bt-mon-uart to determine the uart instance to be
used for bluetooth,uart_pipe and bluetooth_monitor and generate
appropriate configs.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
It is incorrect to call spi_context_release() on a
spi_dw_data object's ctx field before data->ctx->config is first
set in spi_dw_configure(). This is because spi_context_release()
reads ctx->config->operation. In particular, during spi_dw_init(),
calling spi_context_release() reads the uninitialized memory in
spi->ctx->config->operation.
Call spi_context_unlock_unconditionally() instead to properly increase
the semaphore count.
Without this patch, the first call to spi_transceive() can block
forever depending on the value of the uninitialized memory holding
spi->ctx->config->operation.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
It is incorrect to call spi_context_release() on an STM32
spi_stm32_data object's ctx field before data->ctx->config is first
set in spi_stm32_configure(). This is because spi_context_release()
reads ctx->config->operation. In particular, during spi_stm32_init(),
calling spi_context_release() reads the uninitialized memory in
data->ctx->config->operation.
Call spi_context_unlock_unconditionally() instead to properly increase
the semaphore count.
Without this patch, the first call to spi_transceive() can block
forever depending on the value of the uninitialized memory holding
data->ctx->config->operation.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
Added BUILD_ASSERT check for Tx and Rx thread priorities.
The Tx thread priority shall be higher than Rx thread
priority in order to correctly detect transaction violations
in ATT and SMP protocols. The Number of Completed Packets
for a connection shall be processed before any new data is
received and processed for that connection.
The Controller's priority receive thread priority shall be
higher than the Host's Tx and the Controller's Rx thread
priority.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Until Zephyr has infrastructure to enable/disable the
reception of multicast frames we disable the hardware
multicast frame filter completly and pass all multicast
frames to the upper layer and let that deal with them.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
We can use the chosen property "zephyr,console" to determine what uart
should be used as the console and find its name to generate a define for
CONFIG_UART_CONSOLE_ON_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Frequency tolerance for LFRC after calibration for nRF5x
Series ICs is between 251 and 500 ppm as per Product
Specification. For more details refer to:
http://infocenter.nordicsemi.com/
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
By the time we get to POST_KERNEL, kernel services and kernel objects
should be available for use. This should include timers and the random
number generator, but we don't init the system clock until sometime
during the POST_KERNEL phase. Initialize it earlier.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The controller and host-side RX threads recently had their priorities
lowered to 8. Make the driver RX threads consistent with this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The SAM4S, SAM3X, SAME70 all use the uart_sam.c serial
driver. This patch puts the configuration in DTS and
out of Kconfig. The SAME70 uses the USART as well.
USART DTS support for the SAME70 is also in this patch.
Signed-off-by: Justin Watson <jwatson5@gmail.com>
