Rename "nxp,kinetis-lpuart" compatible to "nxp,lpuart" to remove the
device family from its name.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
LPFlexcomm is a MFD device hence select this Kconfig whenever
it is enabled.
Remove the selection from the individual driver Kconfig files.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The Low Power Flexcomm driver manages the interrupt handling
and provides an API to register interrupt callbacks.
Register the NXP LPUART interrupt handler.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Update serial drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
LPUART driver should use shared ISR for all possible use cases,
including ASYNC API, so that multiple features requiring ISR can be
enabled simultaneously.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This PR enables the Ansynchronous UART API for using the MCUX drivers.
It is tested on the RT1062EVKB.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Refactors the mcux lpuart shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. This will allow SoCs with
different clock architectures to reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPUART module, so move the
HAS_LPUART config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
As not all drivers support interrupts we don't have a means to know if
we can allow UART_INTERRUPT_DRIVEN to be enabled and thus various
Kconfig options that select UART_INTERRUPT_DRIVEN. Some drivers have a
interrupts, however not all do. So introduce a Kconfig option to let us
know what the driver actually supports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NXP Kinetis UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all NXP MCUX platforms are using device tree we can remove the
handling for !HAS_DTS from the serial drivers.
Change-Id: I05185142afa7fae83ce68de954202829868af88f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds the base DTS support for the KW41Z Freedom board. The
initial set of changes include SRAM, FLASH, IRQ controller and LPUART
support.
Change-Id: Ic68c4959ddad0c5cfe70d5576a0e58372b93ec9d
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Adds a shim layer around the mcux lpuart driver to adapt it to the Zephyr
serial interface.
NXP has multiple uart hardware blocks that implement different features
and have different register maps. The k64 has a uart block called
'uart', while the kw41 has a uart block called 'lpuart' (low power
uart). The MCUXpresso SDK provides separate drivers for each type of
uart block but with similar software interfaces. As a result, there are
also separate shim drivers in Zephyr. There is a 1:1:1 relationship
between hardware block, mcux driver, and mcux shim driver.
Because we now have two mcux shim drivers for the uart interface, a new
naming convention is created:
<interface>_mcux_<hw block>
Where <interface> is the name of the Zephyr interface, in this case
'uart'. This convention is not new.
<hw block> is the name of the NXP hardware block, in this case 'lpuart'.
This is the new part, and distinguishes different hardware blocks
for the same interface.
Change-Id: I3a80b9bffa116bbb2b02ee950d4bdd79a19a4edc
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
