Now instead of such path:
net_if_send_data -> L2's send -> net_if tx_queue -> net_if_tx -> driver
net_if's send
It will be:
net_if_send_data -> net_if tx_queue -> net_if_tx -> L2's send -> driver
net_if's send
Only Ethernet is adapted, but 15.4 and bt will follow up.
All Ethernet drivers are made compatible with that new scheme also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Change the default behaviour of the host network interface
setup. Now user needs to execute net-setup.sh script from
net-tools project to setup host ethernet interface. The script
needs to be run as a root user. Then zephyr.exe can be started
as a normal user.
Example:
cd net-tools
sudo ./net-setup.sh
This will create zeth network interface and set IP address and
routes properly. See other command line options by typing
./net-setup.sh --help
Old behaviour is still there if one enables
CONFIG_ETH_NATIVE_POSIX_STARTUP_AUTOMATIC=y
in which case one needs to use the command
sudo --preserve-env zephyr.exe
to start the Zephyr process.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can take the zeth interface down by issuing "net iface down <idx>"
shell command. It is possible to take the interface up by typing
"net iface up <idx>" in shell. These commands are important for
native_posix as there is no physical cable that can be connected
or disconnected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow user to configure a program that is executed after the
network interface is created and IP address is setup.
This can be used e.g., to start wireshark to capture
the network traffic of the interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Follow the packet sending error code in the driver. If packet
cannot be sent, then return <0 to the caller and do not free
the packet. In practice this is not happening here but follow
this general rule anyway.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The advantage to this approach allows drivers for
devices that already keep statistics data on hardware
registers to use those instead, rather than try to
replicate it the same counters again within the driver
itself.
The eth_native_posix.c driver though do not benefit
from this, is modified to use the new callback system.
Suggested-by: Jukka Rissanen <jukka.rissanen@intel.com>
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
Allow gPTP code to be run as a linux process and communicate
with gPTP daemon running in linux host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Native POSIX echo server sends malformed response to echo request of
size larger than 128 bytes (default size of each network data
fragment). Wireshark notices that by tagging echo request with "No
response seen". This commit fixes that issue.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
Convert couple of MSEC() calls to K_MSEC() as the timeouts
when using MSEC() are just too long.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Curently only link speed is exposed.
Opportunity taken to remove any post-fix enumerating the iface init
and/or the api: these must be generic and used by all the instances.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This creates zeth network interface in your host and allows user
to send and receive data sent to this network interface.
Fixes#6007
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
