Add initial support for the nPM1100 EK. The EK is expected to be
connected to Arduino header pins (D2/3/4/5).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add entries for the BUCK0/1/2/3 and LDO0/1 regulators. Note that voltage
min/max limits have been set to the hardware limits. They can be
adjusted using overlays in applications, depending on the consumer
circuit constraints.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a sample that demonstrates usage of the nPM6001 PMIC (all of its
functionalities).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When moving nodelabels to <device_name>_<shields_name>, '-' included
in <device_name> was then introduced in the device nodelabel.
But '-' isn't an allowed nodelabel character, hence this is breaking
compilation with those shields.
Convert '-' to '_'.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Shield's nodelabels should now be in the form <device>_<shield_name>.
Besides changing the nodes nodelabels, their usages should be fixed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When adding nodelabels to shields devices, it should be taken car not to
use forbidden characters.
Fix existing occurrence.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This nodelabel was changed while converting all shields to new nodelabel
scheme.
On this particular nodelabel, there was no change to be done, as it doesn't
refer to a node defined in the shield.
Revert this chagne.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This commit updates the outdated link for the "DFRobot CAN BUS Shield
V2.0 schematic."
The repository containing this file has been renamed to
"DFRobot/DFRobot_MCP2515".
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
This commit updates the outdated link for "link board ETH Website" with
that of the "reel board," which contains the information on the "link
board ETH."
Signed-off-by: Stephanos Ioannidis <stephanos.ioannidis@nordicsemi.no>
Use shield-specific sdhc devicetree nodelabels in order not to clash with
sdhc nodelabels from the board devicetree.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add GoodDisplay GDEW042T2 with fast partial refresh. Based on
configuration from GoodDisplay's Arduino example.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Introduce the concept of refresh profiles which are specified as a
child node in the device tree. This makes it possible to use different
overrides for different types of refreshes (full/partial).
The only profile that is currently supported is the "full" profile.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
We're now taking the kscan device from the zephyr,keyboard-scan node. Add
it to the overlay.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
Now that Wifi drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Signed-off-by: Kumar Gala <galak@kernel.org>
The boards folder uses ~142.8 MB, being the largest in the repository.
This is due mostly to board images, which are in most cases not
optimized for web content. This patch tries to address this problem by
converting all pictures to JPEG (quality 75) and by adjusting its size
up to 750 px (the width of the documentation content). Images that
specified a fixed width in rst files are converted down to that value
instead.
With this patch, folder goes down to ~53.5 MB from 142.8 MB (-~63%).
Note that this patch introduces a new set of binary files to git
history, though (bad).
The process has been automated using this quickly crafted Python script:
```python
from pathlib import Path
import re
import subprocess
def process(doc, image, image_jpeg, size):
subprocess.run(
(
f"convert {image}"
"-background white -alpha remove -alpha off -quality 75"
f"-resize {size}\> {image_jpeg}"
),
shell=True,
check=True,
cwd=doc.parent,
)
if image != image_jpeg:
(doc.parent / image).unlink()
for doc in Path(".").glob("boards/**/*.rst"):
with open(doc) as f:
content = ""
image = None
for line in f:
m = re.match(r"^(\s*)\.\. (image|figure):: (.*)$", line)
if m:
if image:
process(doc, image, image_jpeg, size)
image = Path(m.group(3))
if image.suffix not in (".jpg", ".jpeg", ".png"):
content += line
image = None
continue
image_jpeg = image.parent / (image.stem + ".jpg")
size = 750
content += (
f"{m.group(1)}.. {m.group(2)}:: {image_jpeg}\n"
)
elif image:
m = re.match(r"\s*:height:\s*[0-9]+.*$", line)
if m:
continue
m = re.match(r"\s*:width:\s*([0-9]+).*$", line)
if m:
size = min(int(m.group(1)), size)
continue
content += line
if line == "\n":
process(doc, image, image_jpeg, size)
image = None
else:
content += line
with open(doc, "w") as f:
f.write(content)
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The SSD16xx driver currently hard-codes a couple of register overrides
that aren't relevant or even correct for many devices. Make them
optional device tree properties instead.
Note that this changes the behavior for panels that expect
SSD16XX_CMD_DUMMY_LINE and SSD16XX_CMD_GATE_LINE_WIDTH to be set by
the driver. This fixes a bug where the incorrect value
was written to all SSD16xx panels except for GDEH0213B1 and GDEH029A1.
The overlay files for devices that need dummy line and gate line width
to be specified have been updated as a part of this commit.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Now that ethernet drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Signed-off-by: Kumar Gala <galak@kernel.org>
Update lvgl for devicetree updates to use zephyr,keyboard-scan.
Remove Kconfig symbol (LV_Z_POINTER_KSCAN_DEV_NAME) that don't exist
anymore since these values are coming from devicetree.
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that ft8xx drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that eeprom drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Signed-off-by: Kumar Gala <galak@kernel.org>
Devicetree aliases, accel0 and magn0, were recently introduced to enable
sensor sample applications to support multiple sensor drivers of the
same type and thereby reduce the number of driver-specific sensor sample
applications.
This was implemented by adding devicetree nodelabels to accelerometer
and magnetometer sensor nodes, which unfortunately can suffer from
naming conflicts when using shield boards. Fix the problem by appending
the I2C bus address or SPI chip select to the devicetree nodelabel for
sensor nodes on shield boards only. Base boards are left alone to keep
their nodelabels as short as possible.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Remove NET_CONFIG_IEEE802154_DEV_NAME in favor of DT based choice using
zephyr,ieee802154.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Enable the IEEE 802.15.4 radio node on all boards that listed
'ieee802154' in the supported field.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Have the kscan device enabled in devicetree will now get the driver
enabled by default when CONFIG_KSCAN=y is set. So we can remove
driver enabling Kconfig values in various Kconfig.defconfig files.
Signed-off-by: Kumar Gala <galak@kernel.org>
We now 'select I2C' and/or SPI bus in Kconfig in the sensor driver
Kconfig's so there is no need to have boards do the following:
config I2C
default y if SENSOR
config SPI
default y if SENSOR
Signed-off-by: Kumar Gala <galak@kernel.org>
Have the display enabled in devicetree will now get the driver
enabled by default when CONFIG_DISPLAY=y is set. So we can remove
setting driver enabling Kconfig values in various .conf and
defconfig files.
Signed-off-by: Kumar Gala <galak@kernel.org>
All IEEE 802.15.4 drivers are now automatically enabled if they are
'okay' in DT and all of its dependencies are 'y', including
CONFIG_IEEE802154. This means individual driver enablement is not
necessary anymore in Kconfig.defconfig files or samples/tests. Boards
need to still make sure any dependencies are enabled, e.g. SPI bus in
some cases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Set accel0 alias for all boards with the LSM6DSO accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the LSM6DSL accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the ISM330DHCX accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the LIS2DH and compatible
accelerometer to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the LIS2DW12 accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the FXOS8700 and compatible
accelerometer to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the ADXL362 accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Set accel0 alias for all boards with the IIS2DLPC accelerometer
to use by the accel_polling sample.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
For boards with an accelerometer, configure the appropriate bus
(I2C or SPI) default to be enabled if the sensor driver class was enabled.
This change makes no need to add a bunch of board-specific configuration
overlays to the application.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
Now that CAN drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Typically the Kconfig.defconfig* will blindly enable a
sensor and not respect the devicetree state of the CAN.
Additionally we can get problems with prj.conf/defconfig
getting incorrectly overridden.
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that DAC drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Typically the Kconfig.defconfig* will blindly enable a
sensor and not respect the devicetree state of the DAC.
Additionally we can get problems with prj.conf/defconfig
getting incorrectly overridden.
Signed-off-by: Kumar Gala <galak@kernel.org>
The specific drivers for DAC_MCP4725 and DAC_DACX0508 have their
own driver specific Kconfig symbol for the INIT_PRIORITY. So
remove setting the generic one as it doesnt make sense to set it
and the default value matches what the board specific values for
INIT_PRIORITY are set to.
Signed-off-by: Kumar Gala <galak@kernel.org>
Now that ADC drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Typically the Kconfig.defconfig* will blindly enable a
sensor and not respect the devicetree state of the ADC.
Additionally we can get problems with prj.conf/defconfig
getting incorrectly overridden.
Signed-off-by: Kumar Gala <galak@kernel.org>
The UC8176 and UC8179 chips that exist in tree have subtly different
register layouts. Use separate compatible strings for these chips and
a quirks structure that describe device-specific behavior.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
The GD7965 driver is really just a vendor name for the UltraChip
UC8179. Rename the driver to UC81xx since there are other chips in the
family (e.g., the UC8176) with an almost identical register interface.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Now that gpio drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Typically the Kconfig.defconfig* will blindly enable a
sensor and not respect the devicetree state of the GPIO.
Additionally we can get problems with prj.conf/defconfig
getting incorrectly overridden.
Signed-off-by: Kumar Gala <galak@kernel.org>
EPD displays currently have two compatible strings, their specific
model number and the generic driver name. This isn't ideal since we
will need to match on the driver chip model number to work around
subtle chip differences in some cases. Add the specific chip model to
the list of compatibles.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
GoodDisplay used to hide the real vendor of the driver chip in some of
their old data sheets. This is no longer the case and the actual chip
version can be found on their official site. Update the documentation
to show which chip is actually used.
Signed-off-by: Andreas Sandberg <andreas@sandberg.uk>
Now that sensor drivers are enabled based on devicetree
we need to remove any cases of them getting enabled by
Kconfig.defconfig* files as this can lead to errors.
Typically the Kconfig.defconfig* will blindly enable a
sensor and not respect the devicetree state of the sensor.
Additionally we can get problems with prj.conf/defconfig
as well getting incorrectly overridden.
Fixes#48198
Signed-off-by: Kumar Gala <galak@kernel.org>
Remove 'label' property from SDHC nodes. We can use variants of
DEVICE_DT_GET to get access to a device pointer for use in an
application.
Signed-off-by: Kumar Gala <galak@kernel.org>
Add shield support for Panasonic AMG88xx sensor and
remove app.overlay from amg88xx sample.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Simplify the implementation by using gpio_dt_spec.
As part of this use logical values of 0/1 for gpio_pin_set_dt
and handle any inversions as GPIO flags that might be required
at a board level (in dts config).
Signed-off-by: Kumar Gala <galak@kernel.org>
For all boards that have a magnetometer devicetree alias, configure the
appropriate bus (I2C or SPI) default to be enabled when the sensor
driver class is enabled. This will simplify enabling the magn_polling
sample application for these boards (and using the magnetometer in
general) because it will eliminate the need to add a bunch of
board-specific configuration overlays to the application.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Sets a magnetometer devicetree alias for all boards that contain the
LSM303AGR sensor to enable the magn_polling sample application.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Sets a magnetometer devicetree alias for all boards that contain the
LIS2MDL sensor to enable the magn_polling sample application.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Sets a magnetometer devicetree alias for all boards that contain the
FXOS8700 sensor to enable the magn_polling sample application.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Add `status = "okay";` in `arduino_spi` to make sure the node is
enabled (it may not be by default in certain board definitions).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We should avoid use of the label property in devicetrees. The
'zephyr,sdmmc-disk' compatible node has a 'label' property set
but there isn't any code utilizing this so removing the property
from any devicetrees that have it set (as well as example in docs).
Signed-off-by: Kumar Gala <galak@kernel.org>
Adds few missing zephyr/ prefixes to leftover #include statements that
either got added recently or were using double quote format.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
In order to bring consistency in-tree, migrate all boards code to the
new prefix <zephyr/...>. Note that the conversion has been scripted,
refer to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
switch all in tree usage of zephyr,mmc-spi-slot to zephyr,sdhc-spi-slot.
This will change all boards to use the new SD subsystem instead of the
SDMMC SPI driver
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Fix spelling errors in assorted .rst files. The errors were found
using a tool called 'codespell'.
Signed-off-by: Aleksandar Markovic <aleksandar.markovic.sa@gmail.com>
Allow shield to be used with any board that has an
arduino nano connector.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
This maps the Arduino Rev3 header's pins expected by the shield overlay
to the real Arduino Nano header pins of the Arduino Nano 33 BLE board and
aliases the I2C and SPI interfaces accordingly.
Fixes: #43927
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
This update Atmel sam serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The driver is already enabled when turning CONFIG_DISPLAY on and
enabling the display node in Devicetree.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds an overlay defining a dummy arduino_header with three pins
required by the adafruit 2.8 TFT display to work on arduino_nano_33_ble.
While the nano form factor doesn't really have a proper Rev3 header, this
allows to connect the display to the nano pins and make the display work.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
The Keyestudio CAN-BUS Shield (KS0411) is equipped with a Microchip
MCP2551 CAN transceiver with a maximum bitrate of 1Mbit/s.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The DFRobot CAN BUS Shield V2.0 is equipped with a NXP TJA1050 CAN
transceiver with a maximum bitrate of 1Mbit/s.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
In upstream the LV_COLOR_DEPTH_BITS option is called LV_COLOR_DEPTH, this
needs changing if we want to support v8.2.0.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
We're now using the Kconfig copied from the upstream lvgl repository. It
uses the LV_ prefix for all options while we're using LVGL_ for
Zephyr-specific ones. Make the latter consistent with upstream but also
make sure they're distinct from lvgl's by using LV_Z_ as the prefix.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
Start using the upstream Kconfig from LVGL and move the glue code out
of the zephyr tree and put it under lvgl/zephyr/ in modules.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@huawei.com>
Add support for the Keyestudio CAN-BUS shield (KS0411). This shield is
very similar to the DFRobot CAN-BUS shield v2.0.
Rename the MCP2515 devicetree nodes in order not to conflict with
on-chip CAN controllers and switch to specifying the sample point
instead of time quantas.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Kconfig entries used for changing an option default value should not
re-define the option prompt. We should probably introduce a check for
that (any option has a single prompt and help).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove the requirement for specifying #address-cells and #size-cells
properties for CAN controller devicetree nodes.
CAN controllers do not have a common concept of devicetree child nodes
and thus have no need for these properties. This is in line with
upstream Linux kernel devicetree bindings.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove options LVGL_HOR_RES_MAX and LVGL_VER_RES_MAX.
Keep the options for mimxrt10xx_evk boards as they
cannot yet be obtained there from devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Remove Kconfig option LVGL_DISPLAY_DEV_NAME.
Also remove it from mimxrt10xx_evk boards to have consistent
configuration, even if they do not benefit from it that much.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Include common display controller bindings.
Add required height and width properties to "ilitek,ili9340"
and "ilitek,ili9488" users.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Refactors all of the on-chip GPIO drivers to use a shared driver class
initialization priority configuration, CONFIG_GPIO_INIT_PRIORITY, to
allow configuring GPIO drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_DEFAULT or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
Driver-specific options for off-chip I2C- or SPI-based GPIO drivers are
left intact because they often need to be initialized at a different
priority than on-chip GPIO drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Rename the Zephyr chosen property for specifying the default CAN bus
controller from "zephyr,can-primary" to "zephyr,canbus".
The "zephyr,can-primary" property name was selected in antipation of
adding support for redundant CAN networks, which we have yet to
add. Meanwhile, the "primary" term causes confusion for non-redundant
CAN bus configurations (and the "can" term doesn't match the name of the
Zephyr CAN bus subsystem).
The CAN in Automation (CiA) 302-6, which deals with CANopen network
redundancy, uses the terms "default interface" and "redundant
interface". If/when we add support for redundant CAN networks, the
"zephyr,canbus" chosen property can be supplemented with a
"zephyr,canbus-redundant" chosen property.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Refactors all of the EEPROM drivers to use a shared driver class
initialization priority configuration, CONFIG_EEPROM_INIT_PRIORITY, to
allow configuring EEPROM drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The
exceptions are at2x and emul drivers which have dependencies on SPI,
I2C, or flash drivers and must therefore initialize later than the
default device priority.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Refactors all of the DAC drivers to use a shared driver class
initialization priority configuration, CONFIG_DAC_INIT_PRIORITY, to
allow configuring DAC drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The
exceptions are dacx0508, dacx3608, and mcp4725 drivers which have
dependencies on SPI or I2C drivers and must therefore initialize later
than the default device priority.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Refactors all of the CAN drivers to use a shared driver class
initialization priority configuration, CONFIG_CAN_INIT_PRIORITY, to
allow configuring CAN drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The exception
is the mcp2515 driver which has a dependency on a SPI driver and must
therefore initialize later than the default device priority.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Refactors all of the ADC drivers to use a shared driver class
initialization priority configuration, CONFIG_ADC_INIT_PRIORITY, to
allow configuring ADC drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The
exceptions are lmp90xxx, mcp320x, and mcux_adc16 drivers which have
dependencies on GPIO, SPI, and/or DMA drivers and must therefore
initialize later than the default device priority.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Remove Kconfig options for enabling device instances in favor of
taking that information only from device tree. Prior to that
change there was a mix of devicetree and Kconfig.
Bring back use of CONFIG_GPIO_NRF_INIT_PRIORITY.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
It should be "u-blox,sara-r4", because the vendor prefix for this
company is "u-blox", not "ublox".
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Standard Arduino CLK signal is on D13,
nucleo_l476rg board has been modified accordingly.
Need an overlay to use default x_nucleo_idb05a1 spin D3 (PB3)
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This shield is working out of the box on Arduino connector,
even if it is not with all standard Arduino SPI CS/CLK pins.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
There are a number of platforms that the x_nucleo_eeprma2 eeprom sample
can't build on. Also fix issue with missing include of <mem.h> header
to get DT_SIZE_* macros used by the overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds st microelectronics x-nucleo-eeprma2 shield,
which has populated 6 different i2c and spi eeproms.
They are all compatible with the existing at24 and at25 drivers.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
File prj.mcp2515.conf was previously removed from project as it was
made redundant.
Paths containing uppercase CAN were changed to lowercase.
Signed-off-by: Nick Ward <nick.ward@setec.com.au>
Rename the NXP LPCXpresso55S16 board definition from
lpcxpresso55s16_ns (non-secure) to lpcxpresso55s16 and remove TF-M
configuration options.
While the LPC55S16 does have Arm TrustZone support, there is no TF-M
support available upstream yet.
Fixes#35100
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Recently WiFi ESP32 driver (utilizing WiFi radio in ESP32 SoC) was
introduced into drivers/wifi/esp32/ and it already caused confusion as
there was existing drivers/wifi/esp/ directory for ESP-AT
driver (utilizing external WiFi chip, by communicating using AT commands
from any serial capable platform). So question has arisen whether it is
good to merge both, while they are totally different drivers.
Rename ESP-AT driver to be placed in drivers/wifi/esp_at/, so that it is
easier to figure out difference between "esp32" and "esp_at" just by
looking at driver name. Rename also DT compatible and all Kconfig
options for the same reason.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This very first version supports the 160x128 pixels adafruit TFT display
Signed-off-by: Kim Bøndergaard <kim@fam-boendergaard.dk>
Signed-off-by: Kim Bøndergaard <kibo@prevas.dk>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The display controller and SDMMC slot both define GPIOs for their chip
select signals, so enable GPIO drivers by default for this shield.
This missing default was discovered in CI when extending the fat_fs
sample to build with this shield. Many boards enable GPIO drivers by
default, but some boards like sam_v71_xult and sam_v71b_xult do not.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the adafruit_2_8_tft_touch_v2 shield board to enable SDMMC by
default when disk drivers are enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The device tree overlay for the adafruit_2_8_tft_touch_v2 shield board
was incorrectly mapping the Arduino D4 pin, used for SDMMC chip select.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The Semtech SX1272MB2DAS shield is populated with a SX1272 LoRa
transceiver. The base board must provide Arduino header pins
definitions.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Aligning the boostxl_ulpsense shield with all other shield
descriptions by ensuring it has a Kconfig.shield file.
This also provides the Kconfig symbol SHIELD_BOOSTXL_ULPSENSE similar
to the Kconfig symbol available for other shields.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
On stm32mp157c_dk2, the pin mapped on arduino connector pin A3
could not be used as GPIO.
As a consequence, pin "irq-gpio" from x_nucleo_iks01a3 shield
should not be used.
Use board overlay to remove it from shield definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for the BuyDisplay 3.5" TFT + touch shield based on ILI9488
controller and FT6236 touch.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move the data/command GPIO from Arduino header 16 (D10), which collides
with Arduino SPI SS, to Arduino header 15 (D9).
Add commented example for specifying a reset GPIO on Arduino header 14
(D8).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add Inventek es-WIFI modules shield. This shield exposes es-WIFI driver
using Arduino Uno R3 header by UART or SPI interfaces. It shows how
user can create their own overlay and expose es-WIFI driver.
The current Inventek's EVB doesn't have all pins necessary to control
the module by Arduino hearder. This shows how to wire to get ISM43xx
EVB working.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
This change allows to use SSD1306 based displays to be used on the
SPI bus as well.
Adding SPI shield.
Tested on SSD1306 and SSD1309 based displays using I2C.
Tested on SSD1309 based display using SPI.
Signed-off-by: Marco Peter <marco@peter-net.ch>
Move pixel format setting (RGB565/RGB888) to DeviceTree. Add support for
changing pixel format at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add support for the ARM DesignStart DAPLink board for Digilent Arty
S7/A7 (V2C DAPLink) shield.
This shield is designed to be used along with the ARM Cortex-M1/M3
DesignStart FPGA reference designs running on the Digilent Arty.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Align all Kconfig option names with LVGL names. The followed rule:
LV_(.*) -> CONFIG_LVGL_(.*).
Also replaced LVGL boolean configuration entries using if/else/endif
with direct IS_ENABLED macro.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Removes redundancy on atmel_rf2xx.overlay message. Clarifies supported
variations section and notes about network on index.rst.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add note about the availability of touch panel IRQ linei when a jumper
in the board is soldered. A Device Tree commented entry has also been
added to ease testing it.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because the H1 heading was not set in mikroe_eth_click index.rst
file, the shields listing page was listing H2 headings for this
shield.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add devicetree overlay for connecting an Mikroe ETH click shield to an
NXP LPCXpresso55S69 development board.
The LPCXpresso55S69 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ETH click board definition assumes SPI CS0.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Replaces .conf type configuration with .defconfig.
Makes configuration conditional, it depends on shield definition and
networking.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The current shield version shows different configuration, including
disabling default ethernet and wifi interfaces. To allow easy
connection from standard headers, this add two new shield designations.
The existing boards overlays and defconfig were updated.
The documentation was update to reflect changes. A new supported
variations section helps to understand what shield variation user need
select to build their own system.
This changes requires changes on esp32 offload tests to reflect new
esp_8266 shield designations. Sam4e_xpro was keeped as the only one
with dedicated overlay and both frdm_k64f and disco_l475_iot1 were
moved to use standard arduino r3 header using extra args.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The Atmel RF2xx module shield is a generic solution to enable any Atmel
AT86RF2xx IEEE 802.15.4 transceiver. This module enables IEEE 802.15.4
RF2xx Zephyr driver.
The Atmel RF2xx module shield enables any board with an Atmel Xplained,
Xplained-Pro, Arduino or MikroBus expansion header to connect to
networks operation with IEEE 802.15.4, OpenThread or any other stack
based on this media type.
The Atmel RF2xx module is configured to allow interoperate with other
medias like Ethernet. User need configure network stack properlly.
Fixes#26259.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since commit 5963ebaf33
("drivers: spi: CS configuration through devicetree")
the SPI GPIO CS flags are obtained from DT,
but the patch series has missed the necessary changes
in the device trees for displays and link_board_eth.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add devicetree overlay for connecting an Mikroe ADC click shield to an
NXP LPCXpresso55S16 development board.
The LPCXpresso55S16 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ADC click board definition assumes SPI CS0.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use the recently introduced mikrobus_spi devicetree node as parent node
instead of relying on mapping for arduino_spi.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Fixes whitespace in the frdm_kw41z shield document to allow continuation
in the numbered list of Bluetooth controller instructions and to format
the jumper configuration sublist correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Appropriate WS can be loaded automatically if
the display controller has integrated temperature
sensor or an external sensor is connected.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Removed flow control configuration from Kconfig and updated samples
to use device tree for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adds support for a new SHIELD, Eth Click.
Mikro-BUS type shield supported in Zephyr.
Adds Kconfig for mikroe_eth_click shield.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we phase out per instance Kconfig symbols convert to utilize
DT_DRV_INST to initialize CAN instances.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix node status to "okay" instead of "ok" which doesn't
seem to be in used anymore across the tree.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
x-nucleo-iks02a1 shield is an arduino compatible companion board
which can be used on top of Nucleo standard boards for industrial
applications. It extends the Nucleo functionalities adding following
MEMS sensor support:
- ISM330DHCX 3-axis accelerometer and 3-axis gyroscope
- IIS2MDC 3-axis magnetometer
- IIS2DLPC 3-axis accelerometer
- IMP34DT05 digital microphone.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add ESP-8266 modules shield. The ESP-01 needs to be loaded with
ESP8266 AT Bin V1.6.2 which is compatible with ESP8266 AT Bin
V1.7.x which is the minimal supported version by ESP WIFI driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add shield definition for the MikroElektronika ADC Click. The ADC
Click carries a MCP3204 12-bit Analog-to-Digital converter in a
mikroBUS form factor.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The LIS3MDL driver handles DRDY interrupt only. So connect
trigger to the DRDY pin instead of the INT pin.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There is a blue LED used to display connectivity for the SparkFun
SARA-R4 shield. This LED is connected to the modem via GPIO 16
which is the default used by SARA-R4 driver when
CONFIG_MODEM_UBLOX_SARA_R4_NET_STATUS is enabled.
Signed-off-by: Michael Scott <mike@foundries.io>
Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
