Hdc1008 driver is renamed into ti_hdc to prepare it to support all
available Texas Instruments HDC sensors (e.g. hdc1080, hdc2080).
Signed-off-by: Nikos Oikonomou <nikoikonomou92@gmail.com>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add support for pulsing the hardware reset pin of the FXOS8700 high
during initialization.
According to the datasheet, this is required for the I2C/SPI bus
auto-detection logic to work properly if the VDD/VDDIO power
sequencing order cannot be guaranteed.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support to STM LIS2DW12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Co-authored-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2DH driver to avoid
usage of dts.fixup files. The triggered interrupt part has been
slightly hacked to automatically understand whether only int1 is
configured or both int1 and int2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LIS2DS12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Currently it uses high resolution only as power mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm9ds0_gyro driver to get the device name as well as
i2c slave information and gpio info for triggers from device tree.
Updates the build_all test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lsm9ds0_mfd accel/magn driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis3dh accelerometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds dts/bindings/adi,adxl372-spi.yaml for
using ADXL372 on SPI bus instead of I2C which is used
in dts/bindings/adi,adxl372.yaml.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Convert lis2dh accelerometer driver to get the device name as well
as i2c/spi slave information from device tree. Updates the build_all
test accordingly. (issue #11605)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Convert the BMI160 to use Device Tree to get SPI and GPIO params instead
of Kconfig. Updated samples, tests, and arduino_101_sss board support
for this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver fxos8700 can also be used for the MMA8451
accelerometer and offers more functionality.
Revert the commit to avoid duplicate code.
This reverts commit 9c0d7813e5.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Some new yaml bindings that got committed added back in the 'id:' field
which we have removed. Remove it from those dts binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
The 'id' field was never used and tended to just have the compat of the
node. Lets remove it and removed some code in extract_dts_includes.py
related to it. Added a warning if 'id' is set in a yaml so we can
remove it going forward.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Only basic features supported initially but more could be added from:
https://www.nxp.com/docs/en/data-sheet/MMA8451Q.pdffixes#9006
A sample app will be provided in a separate PR.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
This patch adds support for the Analog Devices ADT7420 High-Accuracy
16-bit Digital I2C Temperature Sensors. Optionally sensor threshold
events are supported.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
The LSM6DSL accel/gyro sensor can be accessed through
SPI bus. So the required configuration can be passed through
dts file.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Adds dts bindings for the fxas21002 interrupt pins to all boards that
have this sensor.
The fxas21002 driver is currently only aware of one sensor interrupt
pin, therefore the routing of INT1 or INT2 to the driver is handled in
each board's dts.fixup.
The fxas21002 sample application has been broken since the refactoring
of the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts bindings for the fxos8700 interrupt pins to all boards that
have this sensor. The frdm_k64f and hexiwear_k64 connect both sensor
interrupt pins to the mcu, but the frdm_kw41z connects only one.
The fxos8700 driver is currently only aware of one sensor interrupt pin,
therefore the routing of INT1 or INT2 to the driver is handled in each
board's dts.fixup.
The fxos8700 sample application has been broken since the refactoring of
the mcux gpio driver to dts in commit
4e8f29f319. The sample is now fixed.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for AMS CCS811 Digital Gas Sensor for monitoring
indoor air quality. This sensor reports the following parameters:
1. Co2 concentration
2. VOC concentration
3. Sensor voltage
4. Sensor current
This driver only supports polling mode as of now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Adds dts yaml bindings for the max30101 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxas21002 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds dts yaml bindings for the fxos8700 sensor to allow the sensor
driver name, i2c driver name, and i2c address to be extracted from dts
instead of kconfig.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Provide dts yaml bindings for 4 sensors supported by disco_l475_iot1
board:
-hts221, lis3mdl, lps22hb and lsm6dsl
Devices are denoted as i2c-devices and, as such, inherits from
i2c-device.yaml
Signed-Off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
