Add support for wsen-itds 3-axis accel sensor, provides acceleration,
temperature data reading and supports configuring of output data rate,
operating mode and scale.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The parameters for this fuel gauge depend on the hardware design and
the expected battery. These should not be defaulted to a value that
may be inappropriate. Require that they be explicitly provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert pms7003 sensor driver to utilize device tree.
DTS would look something like the following for the pms7003:
uart {
pms7003: pms7003 {
status = "okay";
compatible = "plantower,pms7003";
label = "pms7003";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update sample overlays. Add GPIO flags to configuration state.
Refactor to split out setup/handle/process phases. Switch to new API
replacing callback dis/enable with interrupt dis/enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since this was converted to the setup/handle/process idiom in master
the conversion is straightforward.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit updates the HMC5883L driver to use the new GPIO API.
Also add a note explicitly describing the active state of the DRDY
pin in the binding file.
Tested on frdm_k64f.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update sample overlay for missing chip select and to deconflict with
UART TXD. Add GPIO flags to configuration state. Replace callback
enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a sample overlay. Add GPIO flags to configuration state. Replace
callback enable with interrupt enable.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update ALERT active level in all devicetree files. Capture GPIO flags
in static configuration. Add internal API to enable and disable
interrupt, to release the handlers when an alert occurs, and to
re-enable the signal when the handler completes. Check for alerts
received during periods when the interrupt was disabled.
Extend the example to handle both above and below range triggers and
alerts that are present on startup.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Correct DRDY active level to default active-high, switch to new
interrupt configuration.
Also fix a common bug where an already-active DRDY signal is not
properly handled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Define a binding for the Bosch BMA280 sensor. Remove the Kconfig
settings and update the driver to use the devicetree information.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add device tree binding for the internal temperature sensor found on
the NXP Kinetis SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a binding for the sensor and replace all Kconfig selection of
hardware parameters with devicetree property values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Johann Fischer pointed out that the driver for this sensor
(master/drivers/sensor/tmp116/tmp116.c) doesn't use GPIOs, in
https://github.com/zephyrproject-rtos/zephyr/pull/21605, though there
seems to be an ALERT pin from looking at the datasheet
(http://www.ti.com/lit/ds/symlink/tmp116.pdf).
Remove the unused property declaration.
I was originally just going to change a 'category: optional' to
'required: false' (and 'type: compound' to 'type: phandle-array').
Either solution is fine with me. Could keep the declaration if people
are planning to use it soon.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
