dmas and dma-names properties could be used by a wide range
of potential dma client, hence put them in base.yaml, as
optional properties.
Since current stm32-i2s driver implementation only support
dma, set these properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add any useful information from 'title:' to the 'description:' strings
(e.g. explanations of acronyms), and remove 'title:' as well as any
copy-pasted "this binding gives a ..." boilerplate.
Also clean some description strings up a bit.
Some other things could probably be cleaned up (replacing 'GPIO node'
with 'GPIO controller' on controllers for consistency, for example), but
I kept things close to the original to avoid accidentally messing up.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit moves DMA parameters previously hard coded in the driver
to the dts.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With https://github.com/zephyrproject-rtos/zephyr/pull/20185, multi-line
descriptions will be formatted nicely, but using '>' breaks it, because
it removes internal newlines (including between paragraphs).
See https://yaml-multiline.info/.
Replace 'description: >' with 'description: |' to encourage '|'. That'll
prevent '>' from getting copied around and messing up long descriptions.
This will lead to some extra newlines in the output, but it's fine.
Line-wrapping messes up any manual formatting.
The replacement was done with
$ git ls-files 'dts/bindings/*.yaml' | \
xargs sed -i 's/description:\s*>/description: |/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Instead of
child:
bus: foo
parent:
bus: bar
, have
child-bus: foo
parent-bus: bar
'bus' is the only key that ever appears under 'child' and 'parent'.
Support the old keys for backwards compatibility, with a deprecation
warning if they're used.
Also add 'child/parent-bus' tests to the edtlib test suite. It was
untested before.
I also considered putting more stuff under 'child' and 'parent', but
there's not much point when there's just a few keys I think. Top-level
stuff is cleaner and easier to read.
I'm planning to add a 'child-binding' key a bit later (like 'sub-node',
but more flexible), and child-* is consistent with that.
Also add an unrelated test-bindings/grandchild-3.yaml that was
accidentally left out earlier.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
For quite a few peripherals that are currently supported by nrfx HALs
or drivers there are no definitions of corresponding CMSIS-Core
peripheral accessing symbols that would provide their base addresses
in the proper domain (secure or non-secure), accordingly to the build
target. This commits adds devicetree nodes for these peripherals so
that their base addresses can be used in definitions of the accessing
symbols mentioned above.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Instead of
properties:
compatible:
constraint: "foo"
, just have
compatible: "foo"
at the top level of the binding.
For backwards compatibility, the old 'properties: compatible: ...' form
is still accepted for now, and is treated the same as a single-element
'compatible:'.
The old syntax was inspired by dt-schema (though it isn't
dt-schema-compatible), which is in turn a thin wrapper around
json-schema (the idea is to transform .dts files into YAML and then
verify them).
Maybe the idea was to gradually switch the syntax over to dt-schema and
then be able to use unmodified dt-schema bindings, but dt-schema is
really a different kind of tool (a completely standalone linter), and
works very differently from our stuff (see schemas/dt-core.yaml in the
dt-schema repo to get an idea of just how differently).
Better to keep it simple.
This commit also piggybacks some clarifications to the binding template
re. '#cells:'.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The 'category: required/optional' setting for properties is just a
yes/no thing. Using a boolean makes it clearer, so have
'required: true/false' instead.
Print a clear error when 'category:' is used:
edtlib.EDTError: please put 'required: true' instead of 'category:
required' in 'properties: foo: ...' in
test-bindings/sub-node-parent.yaml - 'category' has been removed
The old scripts in scripts/dts/ ignore this setting, and only print a
warning if 'category: required' in an inherited binding is changed to
'category: optional'. Remove that code, since the new scripts already
have the same check.
The replacement was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i \
-e 's/category:\s*required/required: true/' \
-e 's/category:\s*optional/required: false/'
dts/binding-template.yaml is updated as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Renaming bindings to consistently be called foo-controller.yaml for
controllers and foo-device.yaml for devices (last one mostly makes sense
for devices on buses and the like).
I was thinking of having a plain foo.yaml be the controller as well, but
!include interrupt.yaml
reads much worse than
!include interrupt-controller.yaml
Another advantage of this approach is that no binding changes meaning
(which could be risky). It's just adding suffixes to filenames.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Sanity-checking each !included file separately was inherited from the
old scripts. It makes it messy to check that combinations of fields make
sense, e.g. to check 'const:' or 'default:' against 'type:', since those
fields might come from different files (this is handy, since it makes
sense to just add/change a 'const:' value, for example).
Drop the requirement that each !included file is a complete binding in
itself, and treat them as binding fragments instead. Only check the
final merged binding.
This also means that !included files no longer need to have a
'description:' or 'title:' (those have always been unused for !included
files), so remove those, and add comments that explain what the
fragments are for instead. That should demystify bindings a bit.
Also fix the descriptions of i2c.yaml, i2s.yaml, spi.yaml, and
uart.yaml. They're for controllers, not devices. These are copy-paste
error from the corresponding device .yaml files.
Piggyback some indentation consistency nits in binding-template.yaml.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* Add "#address-cells" and "#size-cells" to base.yaml as properties
that can exist on any node. Cleanup other bindings that inherit
from the base.yaml.
* Add "status" property with an enum of valid options.
* Add "interrupt-parent" to base.yaml. It's a phandle to the node
which is the interrupt controller for the interrupt.
* Add "interrupt-extended" to base.yaml. Provides a way to specify
an interrupt-parent and specifier in a single property. Useful if
a device has multiple interrupts in which different interrupts go
to different interrult controllers.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In most cases #<FOO>-cells should be a constant. For example in spi
controller #address-cells should be 1, and #size-cells should be 0.
Use the const attribute to specify such single known values. Add const
value to missing bindings which have cells.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No binding has anything but 'version: 0.1', and the code in scripts/dts/
never does anything with it except print a warning if it isn't there.
It's undocumented what it means.
I suspect it's overkill if it's meant to be the binding format version.
If we'd need to tell different versions from each other, we could change
some other minor thing in the format, and it probably won't be needed.
Remove the 'version' fields from the bindings and the warning from the
scripts/dts/ scripts.
The new device tree script will give an error when unknown fields appear
in bindings.
The deletion was done with
git ls-files 'dts/bindings/*.yaml' | xargs sed -i '/^\s*version: /d'
Some blank lines at the beginning of bindings were removed as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Now that the generation script doesn't look at the "generation" in the
YAML, we can remove it from the binding files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
YAML document separators are needed e.g. when doing
$ cat doc1.yaml doc2.yaml | <parser>
For the bindings, we never parse concatenated documents. Assume we don't
for any other .yaml files either.
Having document separators in e.g. base.yaml makes !include a bit
confusing, since the !included files are merged and not separate
documents (the merging is done in Python code though, so it makes no
difference for behavior).
The replacement was done with
$ git ls-files '*.yaml' | \
xargs sed -i -e '${/\s*\.\.\.\s*/d;}' -e 's/^\s*---\s*$//'
First pattern removes ... at the end of files, second pattern clears a
line with a lone --- on it.
Some redundant blank lines at the end of files were cleared with
$ git ls-files '*.yaml' | xargs sed -i '${/^\s*$/d}'
This is more about making sure people can understand why every part of a
binding is there than about removing some text.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Move common properties like 'compatible', 'reg', 'reg-names',
'interrupts', 'interrupt-names', and 'label' into one common base.yaml
that all the other yaml's can inherit from. This removes both
duplication and inconsistent definition.
The device specific yamls just need to say if a property is 'required'
or not.
NOTE: due to some generation conflicts we did not covert
'soc-nv-flash.yaml' to use base.yaml.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
After commit 'scripts/dts: Never ignore properties in
generate_node_defines()', pointless entries for 'interrupt-names'
properties show up in generated_dts_board.conf and
generated_dts_board_fixups.h, because many bindings specify
'generate: define' for 'interrupt-names'.
If 'generation: define' is taken as "generate #define's for this
particular property", then only the 'interrupts' property ought to have
'generation: define'. Having it on both 'interrupts' and
'interrupt-names' makes you wonder what it would mean to only have it on
one of them.
Things get a bit confusing since 'interrupt-names' is still used when
determining the macro names generated for 'interrupts', but it's
probably best to have 'generation: define' work in a consistent way
still (and never be a no-op).
Remove 'generation: define' from all 'interrupt-names' bindings.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit introduces the possibility to have multiple
device nodes attached to the same I2S controller. For this
purpose a new i2s-device.yaml description has been introduced
with the a 'reg' property to define the logic number of the
device. For example, if two microphones are attached to the
same I2S port (say 1) to achieve stereo audio, the two microphones
might be described in dts as:
&i2s1 {
status = "ok";
mic@0 {
compatible = "...";
reg = <0>;
label = "...";
};
mic@1 {
compatible = "...";
reg = <1>;
label = "...";
};
};
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add I2S bus initial support to stm32f4 SOC family.
On stm32f4 the I2S shares same controller as SPI, so
the declarations have been adapted from SPI ones.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
