Moved setting of specific Cortex-M compiler flags in each SoC directory
unify setting them in the arch/arm/soc Makefile.
Add flags for Cortex M0, M0+, M1, M3, M4, and M7. However only
CONFIG_CPU_CORTEX_M3 and CONFIG_CPU_CORTEX_M4 are supported at this time
As part of this change converted Kbuild files for some SoCs into
Makefiles as the Makefiles would be empty otherwise.
Change-Id: Ie4e0178b141ca761ec482a610ae50e94fe58070f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Introduce a soc-cflags, soc-cxxflags, and soc-aflags as a means for
SoC specific compiler flags to be set without manipulating Kbuild
options directly.
Change-Id: I2c8f5019fb237429e59717ef96bd4251a61dc1a5
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Quark D2000 uses the IRQ 10 for the APIC timer interrupt, this
cause a conflict with the "random" IRQ for the footprint benchmark
Change-Id: Iead18821af307832d54b0c9f3db5e52413ba670b
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
ecc_make_key declaration has random size of NUM_ECC_DIGITS * 2 but
definition has (and use) only NUM_ECC_DIGITS.
Change-Id: I18f0d7992b21a2ed7ed99851b1b795cff0a08a10
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
DHCP client support provided for IPv4 over ethernet.
Change-Id: Ia89bc4123842cf109813b80a90b70cf50cc52e0a
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Provide pcap support for echo-apps with PCAP=<filename> option.
For pcap support:
make server NET_IFACE=qemu PCAP=sample.pcap.
without pcap support:
make server NET_IFACE=qemu
Change-Id: Iad90064e0c32134f9c2fda7b28e2cbca1e4e931c
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
The echo-server should work just fine even if the multicast
context cannot be get. By default there are only two contexts
so the multicast would fail always anyway and the program
would not run properly.
Change-Id: Ia9737cbda4a933a208aae020f055f0b6062b4f47
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier default was 8, new default is 4.
Change-Id: I99c9d2aae465fd0feb968efa7417cd28bafd73b8
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier default was 10, new default is 2.
Change-Id: I307a4abaad34223254fd32e1fd4357892a04a2d0
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier default was 10, new default is 2.
Change-Id: I938449d840a244a13e9b9b954648577b76db00bc
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The network context is similar concept as network socket.
Depending on application use, the number of contexts can be
now tweaked. Default value is now 2, it was 5 earlier. Using
the lower number saves 241 bytes of memory.
Change-Id: I6e2a9f053c8c63163af6d6175783233f67553ae9
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This saves little over 4kb of memory.
Change-Id: I4dc3812b11de2736e2bdc17042e47fcdf5cf5491
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User cannot select CSMA mac driver any more in order to save some
memory.
Change-Id: I7805a1c2028f60bc8a428bd5b8f891d540a14b6d
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For CMSIS we now have HAS_CMSIS which needs to be added to the
SoC definition.
Instead of changing the main Makefile we now include a sub-Makefile
with all related header and library paths that are hosted in
ext/
Move redifintion of LIB_INCLUDE_DIR later to get variables defined
in Makefile.toolchain.*
Change-Id: I9f90f90247c2a66b4565427b89d4e1d4dd5c9622
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
for GCC ARM Embedded
When compiling and linking Zephyr with GCC ARM Embedded,
the path to the libraries to be linked needs to be provided
explicitely for the correct variant to be linked in.
JIRA: ZEP-377
Change-Id: I745aa45c7dde12f1cc5c8ea4380b904e086ed94d
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Change the dev name from PWM to PWM_0. This will make it
consistent with other drivers and also fix the device binding
failure in the PWM sample app.
Jira: ZEP-395
Change-Id: I90b945a7e57700d384eaa52e5300c881a3251d83
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
This will allow the driver to be fiber and task safe
Change-Id: I916d4ad67ab6f51f41f3d1136c105e4d1445de48
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This will allow the driver to be safe from fibers and task
Change-Id: I6c4c4fc387cf334f0287b8a02982be1941a311fd
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
For some security scenarios the GDT may already be setup and locked,
in which case the kernel trying to set it again could lead to problems.
Change-Id: I727c1d213479f46a4bb6f0c04a9096131e10b3e7
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The TX fifo threshold is pretty arbitrary.
Set this too big and too many interrupts will occur
for no good reason. Set it too small, and latency
in the SPI transactions is introduced. User's will probably
have to tune this per their application and SPI frequency, etc.
I think setting this to 50% is a good guess for now.
Change-Id: Ib325d40bc7ee10473d99443b3b3cd00fd6e4b95f
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Disabled bluetooth test for STM32F103RB SOC because there is not
enough RAM space for the test.
Change-Id: I9f097d9201ed659c4970b67f42c570331b92bad8
Signed-off-by: Javier B Perez <javier.b.perez.hernandez@intel.com>
Enable warning about updating the MAINTAINERS file when new
files are being added.
Change-Id: I3b13ca25cd01e3254fd4b9e169546a395ebfcacd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Still WIP. Give statistics on memory/flash usage.
Run:
make BOARD=<board> ram_report
or
make BOARD=<board> rom_report
Change-Id: I6b0aee09b89275e12f1cde863d2c0f5b8dfd0409
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The ethernet driver generates a lot of spurious interrupts.
These spurious interrupts have two sources:
1) The Mac Management Counter (MMC) module generates a lot of interrupts
(GMI - bit 27 of the status register). Unfortunately the Interrupt
enable register doesn't allow us to enable/disable it (bit 27 is
reserved). Therefore the only way to mask this interrupt is to mask
all the MMC interrupts (register REG_MMC_RX_INTR_MASK,
REG_MMC_TX_INTR_MASK and REG_MMC_RX_IPC_INTR_MASK). By default
these interrupts are not masked.
2) The RX interrupt is not correctly acknowledged. According to the
datasheet, NIS is a sticky bit and must be cleared (by writing 1
to this bit) each time a corresponding bit, which causes NIS to
be set, is cleared.
Change-Id: I2033973849d87cddc328c65d0d4ad36b5a0c934e
Signed-off-by: Sebastien Griffoul <sebastien.griffoul@intel.com>
This adds simple tab completion for shell use convenience.
Change-Id: If90ded32fb5044741232933d2cb0ce626227d025
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
The ethernet driver calls net_set_mac before net_init is
called (ie before the uip stack has been fully initialized).
Unfortunately net_set_mac calls the function uip_ds6_set_lladdr.
Therefore this function is called before uip_ds6_init: this is an
issue as uip_ds6_set_lladdr is setting some static data which are
going to be erased by uip_ds6_init. In some case it could even lead
to a system hang due to a timer set twice.
To fix this issue net_set_mac should check whether net_init has been
already called. If not net_set_mac should simply copies the mac
address into uip_lladdr. Indeed uip_ds6_init automatically calls
uip_ds6_set_lladdr for the address stored into uip_lladdr.
Change-Id: Ifbcb07e7cd493b6284a85d70f2439d434cebbb00
Signed-off-by: Sebastien Griffoul <sebastien.griffoul@intel.com>
The line below is wrong and useless:
lladdr->state = ADDR_AUTOCONF;
Indeed the three possible values for the state attribute are:
ADDR_TENTATIVE, ADDR_PREFERRED or ADDR_DEPRECATED. ADDR_AUTOCONF
is one possible value for the type attribute.
Moreover uip_ds6_set_lladdr already set the type attribute to
ADDR_AUTOCONF (this done through the call to the function
uip_ds6_addr_add).
Therefore this issue has been simply fixed by removing the line.
Change-Id: I432b7bb6a6a858264bb634f2e4d253f55acbbd5b
Signed-off-by: Sebastien Griffoul <sebastien.griffoul@intel.com>
This allows to register callback that will be called to
perform command completion.
Change-Id: Ide7a0427d9b8bb4dd8cfc0995ef2567b32e89632
Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
Few lines in the doc were out of sync with the code base.
Jira: ZEP-312
Change-Id: Ic0d3508f0f903e43000e17b4a32c1280ae0978dc
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
The .nd on a branch is WRONG if its an unconditional branch. Not needed.
On conditional branches its a compiler feature that is not yet functional
with ARC targets. Typical code for this compiler can use .d to put
something in the delay slot of an instruction, but using .nd is probably
never wanted.
Change-Id: If1017c468e6e7af269ea73daeb4bc223dcc0059f
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Building microkernel for ARC causes a compiler error
due to missing declaration of _sys_idle_elapsed_ticks.
Declare this as extern.
Jira: ZEP-397
Change-Id: I83701f693fea0fcb1ae2c30e0c52abe7987de1f1
Signed-off-by: Ramesh Thomas <ramesh.thomas@intel.com>
Microkernel on ARC works fine, was missing some declarations in the
linker file.
Also enable testing of microkernel with ARC and disable tests where
ARC is not supported yet.
Jira: ZEP-396
Change-Id: I2ac7b8dc0bea22f5d2e24832d9e3afad8df9f580
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
I2C_MSG_RESTART is not used in QMSI driver. What is really needed
here is I2C_MSG_STOP; Missing this flag is causing the issue.
JIRA: ZEP-398
Change-Id: I8fbfe15890c886ede4cce3d2cc68f53758a41e75
Signed-off-by: Baohong Liu <baohong.liu@intel.com>
I notice there are some more places in this file
that can be switched to using tabs.
Change-Id: I7dac2b91f932aa6f167b7eaf93e7c8f571a22d41
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
The file gpio_dw_registers.h already had the 4-port GPIO
registers defined, yet the gpio_dw.c implementation didn't
support it properly. There are 4 ports here, not 2, and only
PORTA can support interrupts and debounce.
On the em_starterkit board, for example, PORTA
has 3 bits for buttons: A, L and R. The other 3 ports should not
be used with interrupts & debounce.
I've re-worked this file to derive the port number from the
base address given. The lower 6 bits are divided by 12 to
derive the port number. From this, the registers EXT_PORTA,
EXT_PORTB, EXT_PORTC or EXT_PORTD can be read.
Also, for those ports that don't support interrupts,
set irq_num to 0, and that code will be avoided. I've verified
that I can access GPIO now correctly on the EM Starterkit. The
em_starterkit board support will be submitted soon but I'm
staging in this change first.
Change-Id: I98dbe083e03e046b40e07b4b14a99a39a6d0f0be
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Convert leading whitespace into tabs in Kconfig files. Also replaced
double spaces between config and <prompt>.
Change-Id: I341c718ecf4143529b477c239bbde88e18f37062
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Defer Prepare write errors to be sent in Execute write response
Per Bluetooth Spec. The Attribute Value validation is done when an
Execute Write Request is received. Hence, any Invalid Offset or
Invalid Attribute Value Length errors are generated when an
Execute Write Request is received. Fixes test case
TC_GAW_SR_BI_33_C (run with shell).
Fixes: ZEP-218
Change-Id: I3dc4583f519e0da2e1f741c9b532d6a6c1970225
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>