Oftentimes, 15.4 PAN IDs are specified in hex. For example, that's
how Zephyr config specifies the default value. So, print them also
in hex, to avoid confusion.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Remove the RD client's stack in favor of using the engine's periodic
service to trigger RD client events. This saves 5K RAM of stack based
memory.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Remove the stack from the device object and instead make use of
the periodic engine service which will trigger the device service
when it's ready.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Stacks cost a lot of RAM in Zephyr. We have 3 total stacks in
the LwM2M lib. We can remove 2 of these if add a service handler
into the main LwM2M engine. Each service can register with this
handler so that they can be called based on their own periodic
timer. The handler itself will search through these registered
services and call them when they become due otherwise sleep
until another is ready.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's use conservative defaults for the LwM2M library to enable
hardware with constrained resources. Users can increase where
necessary.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Let's use snprintk for simple formatting to allow for possible disabling
of printf and protect calls to sprintf from string overruns.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When using Leshan REST API to perform a discover OP on a client, only an
accept field is sent with "application/link-format". Current logic uses
the content-type to determine when a discover OP is indicated. Let's
handle this case as well.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
There were decrements of TCP sequence numbers, inherited from FNET
stack implementation, as was used as an initial base. RFC793 does
not specify conditions for decrementing sequence numbers, so such
decrements are an artifact of FNET implementation. In Zephyr code,
we had to compensate for these decrements by extra increments
(including an increment-by-2). So, remove decrements and associated
extra increments to simplify the code.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Let's rename lwm2m_release_message() to lwm2m_reset_message()
and add a parameter to let the function know whether or not to
release the lwm2m_message resource back to the pool.
By adding the optional release parameter, we can keep the
lwm2m_message but reset the underlying net_pkt / net_buf resources.
This allows us to regenerate the net_pkt after determining
an error has occured. In this case, we don't want the previously
added net_pkt contents but we do want to maintain the message id,
token, etc.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This patch moves from the ZoAP API in subsys/net/lib/zoap to
the CoAP API in subsys/net/lib/coap which handles multiple
fragments for sending / receiving data.
NOTE: This patch moves the LwM2M library over to the CoAP APIs
but there will be a follow-up patch which re-writes the content
formatter reader / writers to use net_pkt APIs for parsing
across multiple net buffers. The current implementation assumes
all of the data will land in 1 buffer.
Samples using the library still need a fairly large NET_BUF_DATA_SIZE
setting. (Example: CONFIG_NET_BUF_DATA_SIZE=384)
Signed-off-by: Michael Scott <michael.scott@linaro.org>
From RFC 7252, section 3
"The absence of the Payload Marker denotes a zero-length payload.
The presence of a marker followed by a zero-length payload MUST
be processed as a message format error."
Check empty payload when COAP_MARKER is found and add a test case to
cover it
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Options parsing helpers functions unable to handle the malformed
packets and dropping it. Improved parsing functionality to handle
malformed packets. Also payload marker is not mandatory in CoAP
packets when there is no payload. Exit gracefully when CoAP
packet contains only options.
Fixes#4396.
Coverity-ID: 178060
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
We need to skip protocol headers when setting pointer to
application data when receiving TLS data.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has enabled CONFIG_NET_DEBUG_APP, then the debugging
version of _net_app_select_net_ctx() was not properly declared
and it caused compile error.
Fixes#4481
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we receive a neighbor solicitation which does not have any
options, then there is no need to assert this condition as that
is a perfectly valid use case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If IEEE 802.15.4 reassembly function ieee802154_reassemble() returns
anything other than NET_CONTINUE, then drop that packet. Earlier
it only dropped the packet if NET_DROP was returned but the reassembly
might also return NET_OK. In that case the pkt is freed already and
pkt->frags pointer is NULL. This caused NULL pointer access in L2 when
packet was received.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This is similar to how few commands already behave if they can
provide additional info to the user if particular config options
are enabled.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_pkt_tcp_data() and net_pkt_udp_data() simply returns the start
address of the header. However the header may span over multiple
fragments, unexpected data or memory corruption might happen when
reading or writing to the pointer directly.
Use net_tcp_get_hdr() and net_udp_get_hdr() instead.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
The net_tcp_get/set_hdr() and net_udp_get/set_hdr() documentation
was not clear in corresponding header file. Clarify how the return
value of the function is supposed to be used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
udp.h is out-of-date as it accesses net buf directly. In 3604c391, it
has been replaced by net/udp.h and udp_internal.h
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Previously net_pkt.h, defined macros NET_PKT_TX_SLAB_DEFINE,
NET_PKT_DATA_POOL_DEFINE, but advertised them as intended for
"user specified data". However, net_pkt.c effectively used the
same parameters for slabs/pools, but this wasn't obvious due
to extra config param redirection. So, make following changes:
1. Rename NET_PKT_TX_SLAB_DEFINE() to NET_PKT_SLAB_DEFINE()
as nothing in its definition is TX-specific.
2. Remove extra indirection for config params, and use
NET_PKT_SLAB_DEFINE and NET_PKT_DATA_POOL_DEFINE to define
system pools.
3. Update docstrings for NET_PKT_SLAB_DEFINE and
NET_PKT_DATA_POOL_DEFINE.
Overall, this change removes vail of magic in the definition of
system pkt slabs/pools, making obvious the fact that any packet
slabs/pools - whether default system or additional, custom - are
defined in exactly the same manner (and thus work in the same manner
too).
Fixes#4327
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
When hexdumping the packet, print also information if we
received / transmitted packet. Also print information if the
hexdump is before compression or not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If building a server that does not support TCP, then the
get_server_ctx() is not needed and thus needs to be compiled out.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Explicitly note that while these functions return pointers to
headers, the headers themselves may be fragmented into different
data fragments. 1a2f24f920 is an example where this might have
been overlooked.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Don't use names like "strlen" for parameters. Try and name buffer
parameters consistently.
NOTE: For several functions I removed "const" flag. This is
intentional and will be needed in upcoming patches.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Remove some left over TODOs and also fix a TODO where we need to return
the appropriate error code to generate a 4.05 response.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation reads the length portion of the COAP header to determine
the length of the coap packet. However, when encrypted via DTLS this
value seems to be getting corrupted. Let's change this calculation so
that it will work for when DTLS is both enabled and disabled. Use the
total length of the fragment data and substract back out the headers
to get a correct value.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When source address is unspecified then SAC is 1 and SAM is 00.
Uncompression does not process because context based compression
is not enabled.
Special case (SAC:1 and SAM:00) should be handled without context
based compression support.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add system workqueue information prints to "net stacks" command.
This helps debugging when figuring out which stack is running out
of space.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Enhance existing "net app" command so that it can be
used to show information about multiple connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we get MAC verification error in handshake, it could be that
everything is fine but we ran out of heap memory in mbedtls.
In this happens, suggest the user to check amount of memory
in mbedtls as it might just fix the issue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As we select net_ctx, it is useful to see who actually called
the _net_app_select_net_ctx() when debugging the call flow.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Sometimes when sending network packet, the wrong net_context was
selected which prevented data to be sent.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We should not close the TLS connection immediately if the TLS
data is not yet sent. So if user calls net_app_close() and we
still have data pending, then send the TLS data and only after
that close the connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As there can be multiple listening network contexts, it should
be possible to close one of them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server is able to listen and serve multiple incoming
connections. This commit does not add support for multiple
incoming TLS connections.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The stack of rd client is exhausted while running lwm2m client w/ IPv6
and network log global enabled. Increase the stack size to 1536 when
NET_LOG_GLOBAL is enabled.
Detail described at #4424
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
".well-known/core" is mainly used with method GET for performing the
resource discovery (RFC 6690). Since we are implementing a LwM2M client
and is not implement a resource directory which allow others to do the
resource registration (POST to .well-known/core). Only GET method is
allowed for the usage. Report 4.5 (Method Not Allowed) if other methods
are requested.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Modify zoap_options_to_path() to return error when URI contains
character other than digits and return 4.04 NOT FOUND to caller.
PATH such as "/1a/2/3" was treated as "/1/2/3" after parsring
which is incorrect.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Return 4.05 Method Not Allowed when path is empty ('/') to the
caller for it's only use by bootstrap delete. This change also avoid the
empty path being treated as request targeted at 0/0/0.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
1) Respond NOT FOUND to caller when object doesn't exist
2) Report as internal server error when OP not handled
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
Such option should be use carefully. Printing out in/out packets is
extremely verbose.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the pkt is corrupted and the offset would be larger than
the actual packet length, then print information about that and
drop the packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Applications may want to be notified when various events
happen in the LwM2M rd client. Let's implement an event
callback which sends: connect, disconnect and update events.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
CoAP allows a proxy to be used when transferring data (CoAP-CoAP and/or
CoAP-HTTP) by creating request on a specific URI path and by using the
Proxy URI CoAP option. Create specific Kconfig options for the proxy
server address and port, until a parser gets implemented.
Code tested with Californium acting as CoAP proxy.
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
[michael.scott@linaro.org: rebased on net_app + lwm2m_message
refactoring + firmware update changes.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During firmware download via block-wise transfer, we can see
packets occaionally get re-transmitted (normal logic in the
pending / retry functions). However, both of these packets
end up coming through the reply handler and we should ignore
any block-wise transfer that has a current value less than
where we expect to be.
NOTE: This fixes K64F ethernet transfers where we were getting
too many packets back in the handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
UDP packets can be lost in heavy traffic. Normally we can handle this
with pending packet processing for packets which have not been responded
to with an ACK. However, due to the time it takes for firmware to
download via CoAP, an extra level of retries should be added.
The process works like this:
Normal pending packets will try to send 3 times fairly quickly.
If that fails, then the timeout callback is called for the firmware
download process. A retry counter is incremented and the timeout
callback perform a new packet send of the block-wise transfer
packet that is missing, until the retry counter hits a limit (3)
and then the transfer is aborted.
This allows for a longer "outage" to happen during firmware transfer
and the process can still succeed.
NOTE: This patch does not fix a current bug where the pending process
is not re-sending the packets correctly, it only makes the process
more stable with a better chance to work.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When a packet expires after the pending retries we call
lwm2m_release_message() to free up resources. This includes
cleanup of the pending structure which calls net_pkt_unref on
the pending packet. This would normally free up the packet
memory. However, earlier in the pending processing we add a ref
to the packet so that normal send processing doesn't free up
the memory. This meant we were leaking packet memory every
time we had an expiration due to timeout.
Let's do an unref prior to calling lwm2m_release_message() to
make sure the packet memory is freed correctly.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Previously, firmware support wasn't initializing the retransmit work
or the extra network packet pools. Let's fix that.
NOTE: While this fixes the setup of retransmit work, the actual
attempts to re-send packets which are pending is failing. Needs
another follow-up fix.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Create an internal function lwm2m_engine_context_init() which sets
the extra packet pools and initializes retransmit work internal to
the LwM2M engine.
This function will be used by firmware pull support which establishes
a new LwM2M context for downloading firmware.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In the case of a proxy server translating HTTP -> COAP (known in
the code as "separate reply"), we were leaking lwm2m_message structures.
This was due to pending objects being cleared out during the first ACK,
and no other way of finding a matching message when the follow up packet
was received. Let's add a second match for reply to make sure we can
find our matching message resources.
NOTE: This change renames find_msg_from_pending() to find_msg() and
makes it a static function as it's only used by the lwm2m_engine.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This is a useful message announcing that the RD client state machine
is starting for a particular connection. If the log level is set
low so that DBG messages are hidden, then this message goes away.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
1. Add handling block1 option in handle_request(). The basic idea is
to declare structure block_context at compiled time and use "token"
as a key to pick up the on-going block cotext. It should be able to
support multiple blockwise transfer concurrently
2. Use write callback implemented in lwm2m_obj_firmware to deal w/ the
update state transition and than call the callback registered by the
application
3. move default_block_size to lwm2m_engine.c to share between
lwm2m_engine and lwm2m_obj_firmware_pull
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on LwM2M net_app changes.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
OPAQUE resource type might/might not have data_ptr/data_len setup
depending on the implementation. This introduce an issue that when
OPAQUE resource is written from the server side, the ones w/ none
setup will not be able to get the data at post_write_cb()
Modify to setup data_ptr/data_len as incoming buffer and buffer size
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
1. Parse firmware pull URI
2. Add lwm2m_firmware_get/set_update_cb() for application to register
callback. This is because we want to check the update_state before
we pass to the application
3. Add lwm2m_firmware_get/set_update_result() and
lwm2m_firmware_get/set_update_stat() to manage the state transition
as well as the sanity check
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: rebased on net_app framework and
lwm2m_message refactoring.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
With future patches we will need to parse URLs in the registration
client and firmware object. Enable it by default when LWM2M is
enabled.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
If there is no connection to server, then _net_app_select_net_ctx()
will return NULL. This is perfectly fine and we can just continue.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use the remote address to determine what address family to bind.
This prevents extra context to be created. In order to avoid
parsing the peer address string multiple times, the client
init function is re-factored.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Currently this is defined as a k_thread_stack_t pointer.
However this isn't correct, stacks are defined as arrays. Extern
references to k_thread_stack_t doesn't work properly as the compiler
treats it as a pointer to the stack array and not the array itself.
Declaring as an unsized array of k_thread_stack_t doesn't work
well either. The least amount of confusion is to leave out the
pointer/array status completely, use pointers for function prototypes,
and define K_THREAD_STACK_EXTERN() to properly create an extern
reference.
The definitions for all functions and struct that use
k_thread_stack_t need to be updated, but code that uses them should
be unchanged.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some doxygen directives were missing from dns_pack.h file.
Also make function header documentation look better.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This creates mDNS responder and serves configured IP addresses
to the callers which want to resolve .local addresses.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User can configure hostname of the device in Kconfig. This can
be used by mDNS responder to answer <hostname>.local queries.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
net_context_sendto() returns an error if dest address is NULL.
If dest address is available, net_conext_sendto() should be used.
Otherwise, net_context_send() should be used.
Fixes#4347
Signed-off-by: Aska Wu <aska.wu@linaro.org>
With the introduction of CoAP and other protocols, URL parsing is
be needed when HTTP_PARSER is not. Let's split out the existing
functionality of URL parsing into it's own CONFIG and let
HTTP_PARSER use it by automatically selecting HTTP_PARSER_URL when
HTTP_PARSER is enabled.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When CONFIG_STDOUT_CONSOLE is not selected, there is no printk()
function. An alternative (printf) must be used.
This fix was taken from tests/crypto/mbedtls/src/mbedtls.c
Signed-off-by: Michael Scott <michael.scott@linaro.org>
It's possible to get number of free pkts/buffers with just
CONFIG_NET_BUF_POOL_USAGE, whereas CONFIG_NET_DEBUG_NET_PKT
depends on CONFIG_NET_LOG and adds quite a bunch of other
overhead. Also, give a hint that this option should be enabled
to get free buffer numbers.
Additionally, use unambiguous "Total" wording to represend the
maximum capacity of data structures, instead of previous "Count".
"Count" (or at least counter) is intuitively something which can
change, so not seeing any other numbers, it's very easy to assume
that it's actually number of free buffers (because that's the
information a user may be interested in in many cases).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the caller has passed net_pkt to prepare_segment(), then
it is caller responsibility to unref it in a case of error.
Fixes#4292
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some chips are smart enough to handle the ACK request flag on
transmitted frames, so it's unneccessary for the L2 to wait for it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is both required in L2's radio part as well as it might be useful
on some ieee802154 radio drivers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These are now fully replaced by set_filter() thus removing their usage
by the L2 layer.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
If the hw supports filtering, L2 will apply the ieee address, short
address or PAN ID filters.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Using radio's get_capabilities, it is possible to know if the driver can
get CSMA work handed-over.
For now, up to device drivers to use
CONFIG_NET_L2_IEEE802154_RADIO_CSMA_CA_* parameters.
Let's see if it will be interesting at some point to enable runtime
modification of these parameters.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of hard coded 1280 bytes MSS, use the MTU of the link
for MSS. The minimal MSS is still 1280 which is mandated by
IPv6 RFC.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adding net_mgmt_event_notify_with_info() which lets the event notifier
to pass dedicated data along with the event. The size of data that can
be passed must be limited to the biggest data passed (which will be
currently IPv6 + prefix).
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current coap library fails to parse or prepare if packet is more
than one fragment. Added support to handle multi fragment packet.
Also well-known/core api used to prepare coap packet and send it
through net context api immediately. This is goind to be problematic
if user doesn't enable net context. Also user can not encrypt coap
packets. Now api will return prepared coap packet to application.
Application will send it to peer.
Jira: ZEP-2210
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
ZOAP library has certain limitations in parsing and preparation of
coap messages. It can handle only on single network fragment. If
network packet is split between multiple fragments it fails. This
patch is just copy and rename of 'zoap' to 'coap'.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
802.15.4 IP-based networking requires 6LoWPAN layer and won't work
correctly without it. So, if NET_L2_IEEE802154 is select,
automatically select NET_6LO. This is similar to what BLE L2
does (NET_L2_BT causes selection of NET_6LO).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is similar to the changes made previously to other network
components: if user selected NET_LOG_GLOBAL, they really mean
they want logging (first of all, error/warning logging) across
the entire network stack.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Due to timeout checking the minimum lifetime must be 15 seconds,
and we're storing the lifetime as an unsigned short so set the
maximum to 65535.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Callbacks are setup for the following states:
- ENGINE_DO_BOOTSTRAP
- ENGINE_DO_REGISTRATION (first registration)
- ENGINE_REGISTRATION_DONE (subsequent client updates)
- ENGINE_DEREGISTER
In most cases, if a timeout occurs the registration engine goes back to
ENGINE_INIT. The exception is a timeout during client update, which
forces the state machine back to ENGINE_DO_REGISTRATION (skipping a
boostrap).
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Sending an lwm2m message is too difficult. It requires pending / reply
and other structures to be configured and set by various portions of
the library. There is also no way to know if a pending message ever
encounters a timeout.
Let's fix this by simplifying the internal LwM2M engine APIs for
handling lwm2m messages:
1. A user calls lwm2m_get_message(lwm2m_ctx) which returns the first
available lwm2m message from an array of messages
(total # of messages is set via CONFIG_LWM2M_ENGINE_MAX_MESSAGES).
2. Next the user sets all of the fields in the message that are
required (type, code message id, token, etc)
3. Then the user calls lwm2m_init_message(msg). This initializes the
underlying zoap_packet, pending and reply structures.
4. Once initialized, the user creates their payload in msg->zpkt.
5. When the user is ready to send, the call lwm2m_send_message(msg).
6. And if for some reason an error occurs at any point, they can free
up the entire set of structures with: lwm2m_release_message(msg).
Included in the refactoring is a timeout_cb field which can be set in
the LwM2M messages. If a pending structure ever expires the engine
will call the timeout_cb passing in the msg structure before it's
automatically released.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Instead of using a magic reference to 8 for token length, let's
establish a define for MAX_TOKEN_LENGTH and then use it for both
variable definitions and to make sure tokens are valid. Also,
Correct the handling of a special token length value (0xFF) which
lets lwm2m_init_message() know to skip token generation. We were
using a -1 value here previously (on a u8_t variable).
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When the net-shell needs to send something to network interface,
it will check if the target address is found in neighbor cache and
then use that network interface. If the address is not found in nbr
cache, then the default interface is used.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some our Zephyr tools don't like seeing UTF-8 characters, as reported in
issue #4131) so a quick scan and replace for UTF-8 characters in .rst,
.h, and Kconfig files using "file --mime-encoding" (excluding the /ext
folders) finds these files to tweak.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
send()/sendto() aren't "front facing" functions, so when user calls
them, context type hopefully should be already validated by other
functions. They are also on critical path of app/network performance,
so getting rid of extra check helps a little bit too. This also
fixes a warning of "err" possibly being used non-initialized.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The implementation is based on net app API. It sends the request and
parses the server reply by following some suggestions mentioned in the
secion "SNTP Server Operations" of RFC 4330.
The system uptime is used as the transmit timestamp of client request
This lib can work on those devices without RTC.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
sendto() and recvfrom() are often used with datagram socket.
sendto() is based on net_context_sendto() and recvfrom() is based on
zsock_recv() with parsing source address from the packet header.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
This patch makes net_context_sendto() work independently without calling
net_context_connect() first. It will bind default address and port if
necessary.
Also, since receive callback should be provided before sending data in
order to receive the response, bind default address and port to prevent
providing an unbound address and port to net_conn_register().
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Introduce net_pkt_get_src_addr() as a helper function to get the source
address and port from the packet header.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
Other parts of the networking subsystem may use net_pkt_ip_hdr_len() on
a packet that has been encrypted for use with DTLS. Let's restore that
value here so those areas don't receive an erroneous 0 value.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The IPv6 address parameters in net_ipv6_send_na() can be const
as the function will not modify them. This avoids compile warning
about parameter constness.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is useful to return the neighbors in net_ipv6_nbr_foreach()
groupped by network interface. This way the caller has them
already in proper order and does not need to re-group them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There was no handler functions for adding, removing and looking up
IPv4 multicast addresses in the network interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the user tried to bind to IPv4 multicast address, then the
operation failed and returned error.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the network interface does not support IPv4 like IEEE 802.15.4
or Bluetooth, then do not print IPv4 information for those interfaces.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the data parameter in net_pkt_insert() is NULL, then just
insert amount of data but clear the area instead of copying.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
User was able to tweak IPv6 hop-limit so introduce similar
feature for IPv4 Time-To-Live value.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the caller of http_client_send_req() sets the timeout to
K_NO_WAIT, then the function would still wait for a while before
returning to the caller.
Jira: ZEP-2624
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The code was accessing wrong neighbor data when it received DAO
message. This corrupted nbr->iface pointer which was clearly seen
by "net nbr" shell command. The corruption then caused random
crashes or hangs when network interface via that pointer was
accessed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the ethernet packet destination MAC address is NULL when sending
IPv4 multicast or broadcast packet, then we must set it as otherwise
we might to access NULL pointer data.
Fixes#1544
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds a new state NET_IPV6_NBR_STATE_STATIC which never timeouts
which is required in case of RFC 7668 which doesn't allow publishing
the address:
https://tools.ietf.org/html/rfc7668#section-3.2.3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In a case gateway is not set drop packet early otherwise bogus
ARPs for 0.0.0.0 are sent.
...
[net/arp] [DBG] find_entry: (0xa8006720): dst 0.0.0.0
[net/arp] [DBG] find_entry: (0xa8006720): [0] iface 0xa800cd80 dst
0.0.0.0 ll 00:00:00:00:00:00 pending 0xa800a7c0
[net/arp] [DBG] find_entry: (0xa8006720): ARP already pending to
0.0.0.0 ll 00:00:00:00:00:00
[net/arp] [DBG] net_arp_prepare: (0xa8006720): Resending ARP
0xa800a380
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
If IPv6 is disabled, then it is useless to try to resolve
IPv6 address because "struct sockaddr" does not have enough
space to store IPv6 address.
Fixes#1487
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
It is useful to clone just the net_pkt which does not have any
data fragments linked to it.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is useful to enable error/warning logging across the net
codebase (less useful for debug level logging, but that's true
for CONFIG_NET_LOG_GLOBAL already).
Implementation-wise, instead of keeping adding to long list of
"select"'s in CONFIG_NET_LOG_GLOBAL and thus introduce component
inter-dependencies, add "default y if NET_LOG_GLOBAL" to
individual components' logging options.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
At the moment we print "Sending ARP packet" even if we found ARP entry
and send the packet directly.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This is the first part of a large refactoring of LwM2M library
message functions and will simplify observer handling later.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
All throughout the LwM2M library we use sockaddr values which are
basically the same as the net_app_ctx's remote addr. There's no
reason to keep these extra sockaddr values around. The net_app
framework client won't accept incoming requests on sockaddr other
than the one we're connected to.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This is the final stage of moving the LwM2M library internals to
the net_app APIs. This means we can support DTLS and other
built-in features in the future. All of the logic for
establishing the network connection is removed from the sample
app.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
In preparation for the move to net_app APIs, we will need
to pass net_app_ctx structures around to the following
functions:
lwm2m_udp_sendto()
udp_request_handler()
Let's add the parameter as net_context for now so the
transition will be smoother later.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This allows use to associate easily the replies / pending operations
with a specific network connection.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The LwM2M library does not use net_app APIs internally. To help
this effort let's establish a user facing structure "lwm2m_ctx"
(similar to http_client_ctx and mqtt_ctx) and start it off by
wrappering the net_context structure.
Future patches will add user setup options to this structure and
eventually remove the net_context structure in favor of a net_app_ctx.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
If no gateway is set, an ARP request for 0.0.0.0 will be sent out,
which is confusing, so log as an error. Of course, logging will
happen only if enabled.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The IPv4 multicast address to MAC address mapping was missing
the 4th byte high bit clearing.
We also need to have some storage for the multicast MAC address.
This was missing which could cause NULL pointer access.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This implements mDNS client from RFC 6762. What this means that
caller is able to resolve "hostname.local" names using multicast DNS.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixes a tx_pkts slab leak since the cloned pkt was referencing the
original pkt slab but was not originated from it (net_pkt_unref uses
pkt->slab when releasing the pkt).
Signed-off-by: Ricardo Salveti <ricardo.salveti@linaro.org>
Because a next networking API call will lead to a crash. Given that
logging can be easily disabled (disabled by default so far!), don't
be shy and call by the name (i.e. error).
Jira: ZEP-2105
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the IP address string is empty, then it is no use trying
to parse it. This was seen when handling DNS server strings when
user has made a mistake and defined the DNS server addresses
incorrectly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adjust length of the packet before setup_ipv4_header() which actually
might increase packet size if there is not enough space available.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Create support for registering a callback that will be called
if the device leaves or joins IPv6 multicast group.
Jira: ZEP-1673
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Commit cd35742a2 missed one unref too many on pending packet which was
triggering a crash which commit 0b8434f08 tried to fix, but it generates
a leak when there is not pending entries left in arp core. Finally,
fixing what cd35742a2 should have done: removing the extra unecessary
unref after sending the pending packet.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Errors has been ignored when using TLV writer to create/write object
instance/resources. Modify to propagate the error back to the caller.
To reproduce the issue, try to create IPSO light control object
instances twice. Since the default instance count is 1, the second one
should be rejected and responded w/ error. But the current
implementation will respond w/ 2.04.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We did not check the requested object/object instance/resource exists or
not before we adding an observer. Correct it by checking the existence
first.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We should stop sending out notification to the peer when the
object/object instances requested to be observed is removed
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
We were using sys_slist_remove() to remove object, object instance and
observer w/o passing the previous sys_snode_t to it (NULL).
This will instruct the function to treat the node as the list head and
result in unexpected behavior after the removal.
Correct it by using sys_slist_find_and_remove() or passing the previous
node to the function.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
When a request demands to create a new object instance, it will search
whether the request object instance exists or not. However, current
implementation does not reset the lwm2m_engine_obj_inst at the time it
is deleted. It only removes the object instance from the sys list.
Correct the behavior by resetting both object instance and resource
instances at the time it's deleted. Also, consolidate function
lwm2m_delete_handler() and lwm2m_delete_obj_inst().
To reproduce the issue, try to create light control object instance
(/3301), delete the created instance and create it again. You shall find
following error message dumped.
> [ipso_light_control] [ERR] light_control_create: Can not create
instance - already existing: 0
> [lib/lwm2m_engine] [ERR] lwm2m_create_obj_inst: unable to create obj -
3311 instance 0
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
If the packet is put pending because ARP request need to be
done, then do not unref original packet.
Fixes#1416
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add a command "net arp" to net-shell. This new command will
print ARP cache contents if IPv4 and Ethernet are enabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The commit 725be227 ("net/mgmt/event: Commands must be > 0 so
masking them works") prevented IPv6 address setting when an
application was initialized. The check in subsys/net/lib/app/init.c
needs to be adjusted because of that change.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There were bunch of config options in tests/net, net-shell and
wpan_serial sample, and those options had wrong name so they
were ignored by the code.
Fixes#1428
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When new connection is accepted, the TCP context variables like
sequence number etc. were not properly set.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For IPv6 check_ip_addr in subsys/net/ip/net_core.c makes a
NET_DBG call to report when a net_pkt is missing a destination
address. An analogous NET_DBG call has been added to the IPv4
destination address checking.
Signed-off-by: John Andersen <john.s.andersen@intel.com>
prepare_arp() was unreferencing original pkt (called pending there) in
case of error.
net_prepare_arp() was always unreferencing pkt, though it could have
been already unreferenced by prepare_arp() as seen previously which is
an extra bogus unref in this case.
And in case it returned NULL, ethernet_send() would return NET_DROP
which in turn would make net_if's tx code to unref again the pkt.
This patch ensures pkt is unrefed only once and at the right place.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The TCP state string is only printed if CONFIG_NET_DEBUG_TCP is
defined. If that is not the case, then the "net conn" command
should not print the "State" column name as the state will not
be printed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This reverts commit 817245c564.
In certain cases the peer seems to discard the FIN packet we are
sending, which means that the TCP stream is not closed properly.
This needs more work so revert this for time being.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When new socket context is created on accepting connection to a
listening socket, its recv_q FIFO should be initialized. Without
initialization, this worked by a chance when FIFO structure was
simple, but recent change to add dlist to it (which now needs
proper initialization) exposed this issue.
Jira: ZEP-2576
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
If the query name is already in numeric format, there is no
need to send the query string to DNS server as we can just
convert it ourselves.
Jira: ZEP-2562
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit removes IP address parsing from DNS init and
replaces it by call to net_ipaddr_parse().
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_ipaddr_parse() will take a string with optional port
number and convert its information into struct sockaddr.
The format of the IP string can be:
192.0.2.1:80
192.0.2.42
[2001:db8::1]:8080
[2001:db8::2]
2001:db::42
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If network context is closed, send FIN by placing it to the end
of send queue instead of sending it immediately. This way all
pending data is sent before the connection is closed.
Jira: ZEP-1853
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
TLS and DTLS are not related to each other so allow DTLS to be
enabled even if TLS is disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The "net app" command was accessing NULL pointer if TLS and UDP were
enabled but DTLS was not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Earlier we modified the original pkt chain when creating IPv6
fragments. This is not a proper way as the original chain might
still be used in TCP when re-sending a message. So when fragmenting
the packet, clone it first and leave original packet intact. This
occupies litle more memory but is now safe.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is very unlikely to happen but the device will access null
pointer if we do not properly check the return value of header
check function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
When trying to figure out where ICMP / TCP / UDP header is located
in net_buf, print more information about what we were doing if the
header cannot fit the first fragment. This is much needed infomation
in debugging weird issues.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Using memcpy() to copy net_pkt is not safe because there are
pointers inside. So use the new net_pkt_clone() to do that.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is needed when one wants to copy the whole fragment chain
and its head pointer net_pkt.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The IP header was stripped by _net_app_ssl_mux() when it received
IP packet. This is fine but if the application expects the get
the IP header, then there is a problem. Fix this by saving IP
header to ssl_context and then putting it back in front of the
packet when the data is passed to application.
Note that this IP header is not used by net_app when the packet
is sent because TLS/DTLS creates a tunnel for transferring packets
and user can only sent packets via this tunnel.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
k_delayed_work_cancel now only fail if it hasn't been submitted which
means it is not in use anyway so it safe to reset its data regardless
of its return.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The original commit 8ebaf29927 ("net: http: dont timeout
on HTTP requests w/o body") was intended to handle a case
where an HTTP response had been retrieved from the server but
the HTTP parser couldn't meet the criteria for calling
"on_message_complete". For example, a POST to a REST API
where the server doesn't return anything but an HTTP
status code.
It was a really bad idea to check a semaphore count. There
is a lot of kernel logic built into semaphores and how the
count is adjusted. The assumption that the value is 0
after the k_sem_give() is incorrect. It's STILL 0 if
something is pending with a k_sem_take(). By the time
k_sem_give() is done executing the other thread has now
been kicked and the count is back to 0.
This caused the original check to always pass and in turn
breakage was noticed in the http_client sample.
Let's do this the right way by setting a flag when
on_message_complete is called and if that flag is not set
by the time we reach recv_cb, let's give back the semaphore
to avoid a timeout.
Jira: ZEP-2561
Signed-off-by: Michael Scott <michael.scott@linaro.org>
The HTTP header field pointers are saved for each HTTP request.
But the counter that saves the pointers was never reset to initial
value when the connection was dropped. This meant that the header
field values were only proper for first HTTP request.
Jira: ZEP-2463
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The server needs global enable/disable status instead of only being
able to enable or disable just the TLS server part.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we have specified AF_UNSPEC when initializing application
server local address, then we try to bind to both IPv4 and IPv6
addresses. The old code did not honor the port number in this
case but used some random value for port.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If user has specified a specific local address, then honor that
and do not try to bind IPv4 context if only IPv6 is defined,
and vice versa for IPv6.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Zeroing-out all bytes from a connection structure when it's
unregistered ensures all state from a previous connection is gone and
can't be mistakenly reused.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If either a remote or a local address were supplied to the
net_conn_register() function, the IP stack would proceed to copy
sizeof(struct sockaddr) bytes from the respective remote_addr
or local_addr pointers, regardless of the actual size of the storage
these pointers point to.
Use the proper size depending on the socket address family.
Coverity-ID: 173630
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
If CONFIG_NET_DEBUG_APP was defined, but neither NET_APP_SERVER nor
NET_APP_CLIENT, build failed due to net_app_cb() haven't beeen
defined. So, define it to empty in this case.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Setting just IPv4 address as was allowed before isn't enough for
real-world usage (e.g. accessing DNS and outside servers in general).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Per LwM2M spec (7.3.2.4 Operation on Object):
"If the payload (New Value) conveys an Object Instance ID in conflict
with one already present in the LwM2M Client, the complete request
MUST be rejected and a "Bad Request" error code MUST be sent back."
Let's do that.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Per LwM2M specification 7.3.2.4, "Optional Resources MAY be conveyed
in the "New Value" parameter as well; the LwM2M Client MAY ignore the
optional resources it doesn't support."
Update TLV/JSON writer to ignore error when object fields are not
found (treated as optional resource). This will allow the resources
supported being written.
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
[michael.scott@linaro.org: re-worked patch post addition of CREATE
operation.]
Signed-off-by: Michael Scott <michael.scott@linaro.org>
Prior to this patch, a CREATE operation was handled as a WRITE operation
after the object instance was created. This becomes problematic when
handling of optional resources differs between these 2 operations.
Let's introduce an actual CREATE operation and use it later to create
these differences.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
We are returning EINVAL from content format write ops when an object
field definition is not found (an optional field which is not
implemented). Instead, return ENOENT which lets the LwM2M engine
know to send ZOAP_RESPONSE_CODE_NOT_FOUND to the LwM2M server at the
end of handle_request().
NOTE: This behavior is not correct when we call the writer right after
a CREATE operation where the data is assigned to resources for the
first time. This case will be handled in a follow-up patch once we're
able to distinguish between a WRITE and a CREATE in the write op
handler.
Signed-off-by: Michael Scott <michael.scott@linaro.org>
