When we send TCP data segment, we need to set the length
of the application data by calling net_pkt_set_appdatalen().
This is done so that sequence number can be properly
advanced when we receive ACK to that pending packet.
Signed-off-by: xiaorui hu <xiaorui.hu@linaro.org>
fix misspelling in Kconfig files that would show up in configuration
documentation and screens.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Make sure we get full name in the commit message and not the username or
some incomplete data that we need to decipher. We still need to verify
the commiter name that is not part of the commit message body, but this
is out of scope of gitlint.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The event mask population used to let the Controller know which events
are relevant to the Host needs to take into account the features
supported by the Controller itself, in order to only enable those that
are indeed valid.
Jira: ZEP-2050
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the framework for LE Scan Request Received Event.
The feature is available under the Controller's advanced
features and will be selected implcitly when Bluetooth v5.0
LE Advertising Extensions feature is implemented.
Jira: ZEP-2073
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Remove unreferenced function hci_evt_is_discardable after
introduction of hci_get_class function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation for refactoring the Controller implementation
into seperate state and role based source files, add Kconfig
options for states and roles in the Controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To guarantee code that is endianness-independent, the sys_le* macros
must be used everywhere when accessing multi-byte values from the
command parameters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In HCI, the response buffer to a command is the same as the one for the
command itself, requiring command parameters to be processed before the
response is formed on the same memory area.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Passkeys are always 6 digits in length and should therefore be
zero-padded if necessary.
Jira: ZEP-2113
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Version 1 kernel (release 1.5 and earlier) is far enough from memory now
to remove the "version 2" wording in the kernel documentation and just
call it "the kernel".
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This creates a common API for network sample applications for
setting up IP addresses etc. The HTTP client application is modified
to use this API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There is no need to unmask/mask the global transceiver interrupt
in kw41z_start/stop as the radio interrupt line is enabled/disabled
anyway with irq_enable/disable calls.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
- set state to IDLE if TMR1 expires, but CCA reports channel as free
- no need to check for CCABFRTX, as the hardware isn't setup to do
CCA before TX
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Sequence timeouts should be scaled to 16us, as TMR_PRESCALE was set
to 62.5kHz.
Also, radio warmup times and TX packet length need to be taken into
account.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Enable it by default now that the eth_dw driver has been ported to the
new IP stack.
Jira: ZEP-1652
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The main difference to how the previous driver operates, is that this
version has zero-copy transmission. The transmit DMA descriptor is
updated for every fragment that is transmitted from the driver.
Another difference in the transmission path is that this version won't
spin indefinitely while waiting for the DMA transfer to complete; an
arbitrary number of busy checks (20) will be performed, and then
the transmission thread will yield for as long as necessary to finish
the transfer.
These two changes should fix ZEP-472; since that issue was opened for
an older version of Zephyr with uIP, I did not bother going all the way
back to test.
This has been only tested with a Galileo board, using Shared IRQ.
Jira: ZEP-1652
Jira: ZEP-472
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The check-compliance.py script uses gitlint to verify the commit message
and takes a range of git commits to validate via the env var
${COMMIT_RANGE}. Previously we used ${SHIPPABLE_COMMIT_RANGE} however
for branches that doesn't get us what we want. So we move to using
origin/${PULL_REQUEST_BASE_BRANCH}..${COMMIT}.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since Controller to Host flow control is a feature that affects both
sides equally, move it to the top-level Kconfig file and consolidate its
use in both Controller and Host.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The purpose of irq_update() is to cache value of UART IRQ status
register for devices which needs such caching. No other driver
performs any other side effects in this call. For STM32, clearing
TC (tx complete) bit was introduced in 8c079e91c9
which is otherwise titled as a conversion to STM32Cube HAL. Thus,
there does not seem to be specific reasons why this code was added.
On the other hand, it leads to behaviorial artifacts when dealing
with interrup-driven UART code (specific issue seen was delaying
of transmitting every other character).
Change-Id: Id20bf214b36eeb6c09e29cc2e6bfca4f7221a1a4
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
* lis2dh 3 axis accelerometer support on SPI and I2C bus
* data ready and anymotion type of trigger support
Tested on Dynastream module D52QD2M4IA-A using SPI
Origin: based on Zephyr lis3dh driver
Change-Id: I2c4e9418b87f09c957bba8f73522bd78830bc809
Signed-off-by: Roger Lendenmann <roger.lendenmann@intel.com>
This feature was removed some time ago, but turns out it's important
to have it available for split host-controller setups.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable the bits corresponding to the new 3 commands supported when
enabling Controller to Host Flow Control, in order for the Host to be
able to enable the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to achieve proper sharing of configuration options, everything
that is common to both the Host and the Controller should now be placed
in the top-level Kconfig file, and Controller-only options are in the
controller/ Kconfig one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Introduce alternative TRX switching using dedicated timers
and peripheral interconnect. This will enable the
possibility to independently configure the Tx and Rx
settings between the tIFS.
Note, this will also provide the opportunity to design a
soft realtime Radio ISR.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The TX and RX pool needs to be split otherwise the TX code path may
consume all buffers causing the RX thread to deadlock which will
possible deadlock the TX thread as well in case it needs more credits.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
The Bluetooth Specification allows for optional Controller to Host flow
control based on the same credit-based mechanism as the Host to
Controller one. This is particularly useful in 2-chip solutions where
the Host and the Controller are connected via a physical link (UART, SPI
or similar) where the Host is sometimes required to ask the Controller
to throttle its data traffic while still making sure that relevant
events get through the line.
This implementation is based on a simple queue of pending events and
data that is populated whenever the Controller detects that the Host is
out of buffers and then emptied whenever the Host notifies the
Controller that is ready to receive data again. Events relevant to the
connections are also queued to preserve the order of arrival.
At this point the Controller ignores the connection handle sent by the
Host and treats all connections equally, and it also queues events even
for connections that have no data pending in the queue. Both this items
can be improved if necessity arises.
Note that Number of Completed Packets will still flow freely from the
Controller to the Host regardless of the pending ACL data packets, which
might lead to inconsistencies in the sequential order of certain
operations that include bi-directional data transfer.
Jira: ZEP-1735
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
There are already helper macros for declaring descriptor fields of
object and array type. Add one for primitive types as well.
The fact that the JSON test code defines one proves that it's useful,
so there should be one provided for other users.
Signed-off-by: Marti Bolivar <marti.bolivar@linaro.org>
This commit provides sample application for sensor hts221.
By default, it is enabled on board disco_l475_iot1
Change-Id: I535fac8a670fa89cc1cae15ea1abe9cfe4b6c56b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
I2C address could not be configured for HTS221.
Remove non existing configuration in disco_l475_iot1 board
Change-Id: Ib5ed8e0f770c16b124cf918bdf9ecd42cdd9b213
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
The FPGA on the MPS2 board implements 4 SBCon devices for I2C which are
connected to:
- a touchscreen controller
- the audio device (for configuration)
- both shield connectors
Change-Id: I55ca985e18b45d68f5e7421c4768dfc9bf2fcb3f
Signed-off-by: Jon Medhurst <tixy@linaro.org>
