echo_server can use up to 6 sockets therefore it needs more file
descriptors than the maximum default value specified.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
These changes modify the function of reading port/pin,
function return logical sum of input pin value and
output pin values for a given port. It is now possible
to read the status of pins set as output.
Signed-off-by: Kamil Gawor <Kamil.Gawor@nordicsemi.no>
There are a small handful of samples that still utilize <board.h>
include, to minimize the use of <board.h> to these specific cases and
allow us to remove adding the board dir to the top level include search
path, we explicitly in each sample add the specific board dir it needs.
For the microbit cases these could be replaced by DTS support in the
future when the pwm_nrf5_sw supports DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allow to set debug also for RAW_CHANNEL and set general debug template
instead of networking one.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Set COVERAGE option using an overlay instead of piping it through CMAKE
which breaks dependecies, i.e. if someone wants to disable that option
on the application level.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add yaml file for initial support of USB PHYs.
It adds also yaml files for STM32 USBPHYC and
USB controllers with embedded PHY.
PHY refers to the physical layer which is used
to connect a device to the physical medium e.g.
USB controller.
Origin: original
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commit optimizes the process of checking that the
added partitions in a mem_domain are sane. It places the
sane_partition checking inside the loop of adding the
partitions in the mem_domain, so that the checkings are
not performed twice, and no partition is checked against
itself.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit fixes the calculations of the partition ending
addresses in two places in the code, according to:
<last> = <start> + <size> - 1. We also rename 'end' to 'last'
to stress that we calculate the last address in the partition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
USB is desired to be configured by default and hence the Kconfigs
are addressed in _defconfig for intel_s1000_crb. Cleaned it up
from the app level prj.conf which was anyway redundant.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Now states which are bound have single timer that means
means for lightness variation there is one timer & for
temperature variation there is one timer.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Corrected mapping of message handler for Generic
Move Set, Generic Move Set Unack, Light CTL Set &
Light CTL Set Unack.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Removed extra blank line. Add new
bound_states_transition_type_reassignment() function in
transition.c to improve code readability & understanding.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
This edition would improve by default mesh network
performance. This is after testing with nRFMesh app
from Nordic Semiconductor.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Converts the adxl362 sensor driver to get the device name and spi slave
properties from the device tree rather than Kconfig. Updates the
build_all test accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
According to the "USB Mass Storage Class" Spec. the serial
number shall contain at least 12 valid digits, represented
as a UNICODE string.
Fixes: #11336
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Include regex pattern matching of console output
to determine the sample execution status.
Add fixture to determine the hardware dependency
if any. If FRAM is connected to board externally,
then with fixture, automation would be able to
identify the board with sensor to trigger the
execution.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
Regex pattern matching is included to match the
execution log from console to return test result
in automation.
Also add fixture to identify the external sensor
connected for automation framework to trigger test
cases on particular board which is connected with
required sensor.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
Support specifying a test fixture attached to a board to filter in/out
tests that require this fixture to be able to run a test.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In the MULTI_LEVEL_INTERRUPTS Kconfig we have a symbol for defining
the maximum IRQ per aggregator: MAX_IRQ_PER_AGGREGATOR
Instead of using a hard-coded value of 32 max irq per level,
let's use the value of MAX_IRQ_PER_AGGREGATOR
Signed-off-by: Michael Scott <mike@foundries.io>
If CONFIG_3RD_LEVEL_INTERRUPTS is not enabled then we see the following
error during sw_isr_table generation:
Traceback (most recent call last):
File "zephyr/arch/common/gen_isr_tables.py", line 291, in <module>
main()
File "zephyr/arch/common/gen_isr_tables.py", line 199, in main
if syms["CONFIG_3RD_LEVEL_INTERRUPTS"]:
KeyError: 'CONFIG_3RD_LEVEL_INTERRUPTS'
ninja: build stopped: subcommand failed.
Fix the logic to look for the symbol instead of referencing it.
Signed-off-by: Michael Scott <mike@foundries.io>
The following addition `depends on !(file in "ext")` allows
to exclude `ext/` warnings reported by coccinelle scripts.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
We still have one platform using (for now) the pre-asm2 integration
where the timer interrupt was handled via custom assembly. It calls a
function named "_timer_int_handler" always, not the one we register
with IRQ_CONNECT.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The old xtensa layer had an unused/untested facility where it would
apparently try to slave a timer tick to an arbitrary interrupt. The
legacy headers were still checking the kconfigs used to enable that
even though nothing wants it and the new driver has removed them,
breaking builds on platforms like S1000 that still use the older
layer.
Don't try to finess this as these files are going away. Just make
them local preprocessor symbols and set them to the default values
they always had.
(Note: the feature doesn't sound like it would have been so bad,
actually. We should probably crib that idea of having an
"external_tick" driver, but there's no reason for it to have been
arch-specific.)
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Xtensa interrupts are handled generically, by testing a set of flagged
interrupts in the INTERRUPT register. It's not possible to know
exactly which device "caused" an interrupt.
The entry code was dispatching correctly, but it was failing to test
the enable state in INTENABLE. Such an interrupt will never "fire",
but it might still be flagged, and if we happen to end up handling an
interrupt of the same priority (due to some other device) the entry
handler would incorrectly invoke the disabled interrupt.
Found by dumb luck and a comedy of errors: the recent timer driver
change swapped the counter in use, which changed the interrupt number
to one shared with the I2C driver, whose early interrupts (odd that
this device is interrupting on boot when not in use, but whatever)
would then discover the OTHER timer counter had been flagged and try
to invoke an ISR for that other counter, which was the _irq_spurious()
spurious interrupt handler.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The firmware starts us with an already-initialized UART and a simple
ROM hook. Use that as the default printk handler so we can log in
very early boot. It will be overriden later (as it happens, by
another handler based on the same firmware hooks).
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Architecture init code and/or HAL layers often have a working
"putchar" routine available long before the Zephyr driver layer is
initialized.
Make the default printk() output a weak symbol, so it can be
overridden on these platforms.
Also remove the kconfig depedency on CONSOLE_HAS_DRIVER, as this is a
non-driver mechanism.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
