Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for pulsing the hardware reset pin of the FXOS8700 high
during initialization.
According to the datasheet, this is required for the I2C/SPI bus
auto-detection logic to work properly if the VDD/VDDIO power
sequencing order cannot be guaranteed.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add basic verification of the supported devices.
Add IDs for MMA8451, MMA8652, MMA8653 and FXOS8700 and
remove Kconfig FXOS8700_WHOAMI option.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
A race condition was identified during the initialization of the
driver when the trigger function is enabled. This exposed two issues:
1 - The fxos8700_handle_int is trying to acquire the semaphore before
it gets initialized. To solve this we need to initialize the
semaphore before calling the fxos8700_trigger_init function.
2 - During the fxos8700_trigger initialization the i2c bus is used
(from fxos8700_handle_int function) at the same time as the
fxos8700_set_power is being called. To fix this we need to
initialize the semaphore with 0 and just release it after calling
the fxos8700_set_power function in the fxos8700_int
These two scenarios was reproducible in the WaRP7 board with i.MX7 SoC.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Some device include a temperature sensor, usually used as a
companion for helping in drift compensation, that measure the
die temperature. This temperature IS NOT related to the the
ambient temperature, hence a clean separation between the two
is required.
This commit introduces a clean separation between the two
types of temperature leaving the old deprecated definition
still there.
The list of current drivers that read the die (and not the ambient)
temperature is the following:
- adxl362
- bma280
- bmg160
- bmi160
- fxos8700
- lis3mdl
- lsm6ds0
- lsm6dsl
- lsm9ds0
- mpu6050
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit e60af3be66.
We revert this as we intent to move away from {u}int{8,16,32,64}_t types
to our own internal types for sized variables so we shouldn't need the
PRI macros anymore.
Change-Id: I4a57eb2c23cb1b137112224f604602d40c7cce4f
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To allow for various libc implementations (like newlib) in which the way
various {u}int{8,16,32}_t types are defined vary between both libc
implementations and across architectures we need to utilize the PRI
defines.
Change-Id: I69e60e3823028389b314adaf6e279fd47fde1182
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The fxos8700 is primarily an accelerometer/magnetometer, but it does
also include a temperature sensor. Note that the temperature sensor is
uncalibrated and can only be used when the magnetometer is enabled
(magnetometer-only mode or hybrid mode).
Change-Id: I74c4ae68c30e0f9836caa70baed44ad8956b17ea
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SENSOR_CHAN_*_ANY will be deprecated, so use the new SENSOR_CHAN_*_XYZ
enum values.
Change-Id: I91cf25864613a934feab65588969d10c52fd4fe6
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove the type field from the sensor value structure. All values will
have the type previously defined by SENSOR_VALUE_TYPE_INT_PLUS_MICRO.
This simplifies the interface, as apps will know what value type to
expect. Apps that prefer to use double values can optain them using the
sensor_value_to_double function.
Change-Id: I3588d74258030eb16c3f89d8eead13cca4606b18
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
Adds optional support for tap and double tap sensor triggers to the
fxos8700 driver using the pulse detection hardware function.
Default configuration values were taken from NXP AN4072, section 6.3.
http://cache.nxp.com/assets/documents/data/en/application-notes/AN4072.pdf
Change-Id: Ia95091628a853eb956f6fd1df099a9e6e101b707
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds general sensor triggering support to the fxos8700 driver, including
options for the driver to use its own thread or the global workqueue
thread to handle sensor interrupts. Adds specific support to handle the
data ready sensor trigger.
Jira: ZEP-1395
Change-Id: I092f22e35747b92a88eb71a3d162a4fc16227b45
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
move both semaphores and nano_work objects to unified kernel APIs.
Change-Id: Icca8a091063544c451e47201cd8e956b95010513
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Adds basic sensor driver support for the NXP FXOS8700 6-axis
accelerometer/magnetometer. Currently this driver supports
accelerometer-only, magnetometer-only, and hybrid (accelerometer +
magnetometer) modes, as well as 2g, 4g, and 8g accelerometer full scale
ranges.
This driver does not yet support any sensor triggers such as the data
ready trigger, or runtime changing of sensor attributes.
Datasheet:
http://cache.nxp.com/files/sensors/doc/data_sheet/FXOS8700CQ.pdf
Origin: Original
Jira: ZEP-721
Change-Id: Iff0f751c737196f60d5c5d3448631b57093ece34
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
