This enables the ACPI_EC1 interface which is typically accessed
through ports 0x6A0 and 0x6A4 in Bios.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Espi has three uart port from 0 to 2 and uart sirq need to enabled for
the port which is active in the hardware. An active uart sirq shoudl be
enabled based on uart mapping configuration.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
MCHP Soc operation uses clear-on-write register for interrupt
status, read-OR-write operation may clear interrupts unintentional.
Fixes#24464
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Espi bus interrupts need to re-enable after espi reset to get
all espi bus and vw signal interrupts.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
Epsi slave need to respond with an OOB_RST_ACK for OOB_RST_WARN sent by
master during host reset. Enable interrupt for OOB_RST_WARN to receive
signal changes and respond with ACK.
Signed-off-by: Venkataramana Kotakonda <venkataramana.kotakonda@intel.com>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Convert older DT_INST_ macro use in microchip drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Expand configuration mechanism for additional eSPI host warnings.
Notify client driver when sleep A virtual wire is received.
Simplify virtual wire interrupt enabling.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
MEC15xx eSPI OOB RX length register holds received message length
and receive buffer length, need to extract rcvd msg length.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Convert driver to use DT_INST_ defines. The preferred defines for
drivers are DT_INST_. The driver mostly used DT_INST_ defines but
a few IRQ priority defines needed conversion.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix#22188
Introduce config option to disable automatic acknowledge via
virtual wires on response to eSPI host suspend and reset warnings.
This will give the opportunity for eSPI slave systems that need to
perform preparations before reset or suspend.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Enable ESPI OOB channel by default in XEC driver.
Enable OOB channel transmit interrupt and handle OOB up/down correctly.
Change interrupt clearing, clear low level interrupt bits in subhandlers
and high level interrupt in aggregate handlers at the end.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Initial implementation of the keyboard controller peripheral
in the eSPI driver. This allows to communicate ps2 and kscan
data between EC and Host
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
When a eSPI slave needs to send back-to-back packets
updating status signal need to guarantee both status
reach the eSPI host, i.e. SCI=0 followed by SCI=1.
This change guarantees both packets are transmitted
over esSPI bus.
Allow to map eSPI host logical UART to a soc UART.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
In status variable in espi_pc_isr should have been a 32-bit unsigned int
as ESPI_PC_REGS->PC_STATUS is 32-bits.
Fixes#18359
Coverity-CID: 203521
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add eSPI Microchip XEC driver
Include support for peripheral & virtual wires (channel 0-1)
OOB and flash support can be added in the future
Fix compilation error in pinmux driver
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
