Fix a few small (mainly rendering) issues with the arduino_101.rst
document:
- A few paragraphs had the wrong indentation
- A sub-list did not appear as such (serial port settings)
- Remove the 'Bibliography' section which appears empty
- Fix IO-3 and IO-5 pin names in note
Change-Id: I60ad839de1901167b6793254186836015502aaab
Signed-off-by: Geoffroy Van Cutsem <geoffroy.vancutsem@intel.com>
This checks if the command string is either NULL or empty since in these
cases there shouldn't be necessary to do any lookup.
Change-Id: I27e6d5b07ab4000cce93a4d1f7952e3c57672657
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Contrary to strcmp strncmp does not match the entire string only the
initial bytes passed as len thus causing a prefix match not a exact
match logic.
Change-Id: I85f96beb2249223f44c81c4efd6bd01bf2033a2e
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch fixes returning invalid offset, invalid attribute length
error. Error should be set during prepare write and returned in
response to execute write request as error response.
Change-Id: I78c57abc5f6f2fbd4a2c0fbb1ee6532212679a36
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@tieto.com>
Firmware does not filter by UUID so we need to do this ourselves.
Change-Id: I55808836369194fbc5ea7c35db2c72fcda75e4eb
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
This removes optional write permission to the ES Trigger Setting
Descriptor. These setting can be set by application.
Change-Id: Ic62ebd909c10601955e67b38303b8c852971203e
Signed-off-by: Mariusz Skamra <mariusz.skamra@tieto.com>
TCP client only sent one SYN and if that was lost, the connection
was not initiated correctly.
Change-Id: Iebb0b719a3d01d2e4f56ed911b3ed94643e53941
Jira: ZEP-385
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adds testcase.ini files for the floating point sharing tests to
ensure that there are run on a daily basis.
Change-Id: I206b1734700f6e998c19d7ad1b36a84400284899
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Fixes a bug in _ExcEntSetupDone wherein the return address to the
exception stub was accidentally changed to point to the TCS of the
interrupted thread.
Jira: ZEP-378
Change-Id: I0e502649c49c35ba8b2457016ede4a6b586da3fb
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
IP packet passing through 6lowpan compression and 802.15.4
fragmentation has an issue. (RFC 6282 and 4944) RFC4944, 5.3
says "fragment header's datagram_size and datagram_offset
values as the size and offset of the IPv6 datagram before
compression".
At the moment datagram size and offset values are after
compression. Due to multiple bearer (15.4 and bluetooth) support
and multiple incoming buffers support functionality is divided
to compression and fragmentation parts. And datagram size and
offset values for BT are after compression. Small packet (which
doesn't need fragmentation) doesn't go through this. So cacheing
compressed and uncompressed header lengths and with hdr difference
preparing fragments as per original buffer (total buf size and offset).
Change-Id: I9d3b0433e64964c68519d7c007cc06ec6035b573
Jira: ZEP-208
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This adds help strings to commands describing what parameters they take:
btshell> help init
init [none]
btshell> help connect
connect <address: XX:XX:XX:XX:XX:XX> <address type: (public)>
Change-Id: I0b79cb4f2d424f74b0ddb1de7a6d7120e81e2ae3
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This adds a optional help string to the command table which is printed
when user enters > help <command>.
Change-Id: Id3a8995bb6c4ff6b009418e31968c0677e6e4921
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
I've tested that CONFIG_XIP does work with Harvard.
User's can build CONFIG_XIP=y, and then have their bootable image
be placed in SPI-FLASH. A bootloader will load up ICCM contents.
Zephyr will then copy remaining data from ICCM to DCCM.
This takes a bit of ICCM memory to do it, but it will work.
Change-Id: Ic1cd201d19aab9083d63334527d9d68f4edc6075
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
When using the Synopsys DesignWare Synchronous Serial Interface (SSI),
the FIFO depth can vary from 2-256, depending upon how this module is built.
For quark_se_ss, it was using a depth of 8. For EM Starterkit, it will be
32. Adding this now as a configurable option. A larger FIFO really helps
reduce SPI interrupts.
Change-Id: Id2bc8470bfc08ab447d38b89c7904cff010c63bd
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
Just as rxftlr can be read, a macro is needed so that txftlr can be read.
Symmetry.
Change-Id: Id987f700d89268feca60850f4fdf512f990f3ab6
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
A recent submission caused a build error for DW
CONFIG_SPI_DW_INTERRUPT_SINGLE_LINE because the symbols
CONFIG_SPI_<0,1>_IRQ went missing from Kconfig.
I think these should probably NOT be configurable, because
on an SOC, interrupt lines are hard. So I'm changing
the names back to SPI_DW_PORT_<0,1>_IRQ, with there
definitions originatig in the soc.h file.
Also, on DesignWare ARC EM Starterkit, the SPI interface
has 6 slave selects, but IP itself can handle up to 16.
Why does this start from 1 and not 0? Argh!
DBG_COUNTER_RESULT() should expand to 0 when not used.
Also, don't check version from DesignWare IP because
it can be different for each target.
spi_dw_isr() requires a cast when converting arg to dev.
Change-Id: I83d55e0405583e7cafab80b09cbef44e0f96fcb8
Signed-off-by: Chuck Jordan <cjordan@synopsys.com>
By default, instead of spamming the build output with one warning per
file where __assert.h is included when CONFIG_ASSERT=y, only display a
warning at the end of the build.
Also limit the range of CONFIG_ASSERT_LEVEL between 0 and 2.
Change-Id: I95ffd1bcec9535de1afabc047814e5c6f5b9c2c1
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Overflowing the k_server command stack will now trigger an __ASSERT()
when CONFIG_ASSERT=y.
Change-Id: Icf6f4242ab8a9897918769415a0f7485602d7630
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This patches includes
- a profiler file/Makefile that can be added to an application to enable
kernel event logger flush over UART
- a nanokernel and a microkernel sample application permitting to
exercise the profiler
- scripts permitting to get kernel event profiler data over UART
console and post-process this data
Origin: Original
Change-Id: Icacf4354c526c7f780b11371e9c28c87e6461eb8
Signed-off-by: Fabrice Olivero <fabrice.olivero@intel.com>
Update the zperf app in order to support ipv6.
Change-Id: I137af07bbd739cf4bfe60bd13bdb06cf939c6c55
Signed-off-by: Sebastien Griffoul <sebastien.griffoul@intel.com>
For xtools, add sysroot also to include search path.
Change-Id: I72d37c54eb7f3693d3a207a35802b29b150c84f1
Signed-off-by: Sakari Poussa <sakari.poussa@intel.com>
This patch adds the TCP server capability
to zPerf tool.
Change-Id: I8e4d92b10079a7c4b4bddab8d78655031ca6125c
Signed-off-by: jgarcia <jeremie.garcia@intel.com>
* Rename BMP280 to BME280 which is a superset for the former.
* Autodetect device based on chip ID.
* Implement humidity fetching and reading for BME280
* Rename sample BMP280 to BME280
Change-Id: I565c769a7011e7496c9f1cad861d5ee311839b4f
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Check if return value is negative when checking for errors, instead of
checking if it's 0.
Change-Id: I0b0af28c02b3760f3128e8cbe48908dabc89af88
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Update all drivers that have vectorial data to return all 3 channels (X,
Y and Z) if the chan parameter is _ANY.
Also fix a compile bug in LSM9DS0 MFD driver.
Change-Id: I5bf261846bcd68c288b96997ff164726f75c151c
Signed-off-by: Murtaza Alexandru <alexandru.murtaza@intel.com>
Document the process of creating and flashing a MyNewt-based HCI
firmware for the Arduino 101.
Change-Id: Ieb3cf116363777b8cca20dbcc746e4757f47d2ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This accidentally snuck by between iterations of the workqueue patches.
In v1 there was a sensor-specific workqueue, which we then turned into a
global one.
Change-Id: I10b193bb535602a16f6742d057281ba01906228d
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
By calling the microkernel entry point 'main' there's no need to have
extra hacks to share the same c-file with both nano and micro
configurations.
Change-Id: I6623855a87ef8624b2bddb75b95079521e0eab8b
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add additional check which verifies that MAC address is given
and return -EINVAL if it is not set.
Change-Id: I90d415670c4b35d092ba057329f998df3a72018e
Jira: ZEP-213
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The application can initiate TCP connection when using IPv4.
Change-Id: I264270d013f567dd0c429783c47506d9c38f0509
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The echo-client can now initiate a TCP connection.
Change-Id: I8223ef377127319dd1791497675a4abe8b382365
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The application can initiate TCP connection when using IPv6.
Change-Id: I632fa2559d5deb40d71288762bd13fbc2aac9cc7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If the active connection to another TCP host fails, then
quit as it is no point continuing.
Change-Id: I21317d7062d4ac93c342834a2503139fe27076e7
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If we are initiating a TCP connection, then make sure that
we try to re-send initial SYN packet (max 8 times) if it is lost.
Change-Id: I9fbc39bdaef3a535c480eb5433eb7ef3ad60d604
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This will be used in following commit.
Change-Id: Ie4fccd72471c285b68a6df6970babe562e5e6258
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
