Add api to raise SGI to target cores in affinity level identified
by MPIDR. Currently only EL1S is supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
If IO APIC is in logical destination mode, local APICs compare their
logical APIC ID defined in LDR (Logical Destination Register) with
the destination code sent with the interrupt to determine whether or not
to accept the incoming interrupt.
This patch programs LDR in xAPIC mode to support IO APIC logical mode.
The local APIC ID from local APIC ID register can't be used as the
'logical APIC ID' because LAPIC ID may not be consecutive numbers hence
it makes it impossible for LDR to encode 8 IDs within 8 bits.
This patch chooses 0 for BSP, and for APs, cpu_number which is the index
to x86_cpuboot[], which ultimately assigned in z_smp_init[].
Signed-off-by: Zide Chen <zide.chen@intel.com>
Add basic driver for GIC V3 interrupt controller.
This implementation supports
- distributor, re-distributor and cpu interface initialization
- configuration and handling of SPI, PPI and SGI.
- V2 Legacy mode is not supported and uses system interface.
Current implementation supports GIC secure state only.
All interrupts are routed to Secure EL1 as 'irq' by configuring
them as Group1 Secure.
TODO:
- MPIDR based affinity routing setting.
- percpu redistributor probe
- message based SPI and SGI generation api
- EL1NS support. Legacy mode support.
- LPI/ITS is not supported.
Signed-off-by: Sandeep Tripathy <sandeep.tripathy@broadcom.com>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the GICD_SGIR register (used for generating software
generated interrupts) field definitions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit fixes the field definition names for `GICD_ICFGR`, which
were incorrectly prefixed with `GICC_`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The current Generic Interrupt Controller (GIC) driver makes use of the
multi-level interrupt mechanism and `irq_nextlevel` public interface.
This is a less-than-ideal implementation for the following reasons:
1. The GIC is often used as the main interrupt controller for the
Cortex-A and Cortex-R family SoCs and, in this case, it is not a 2nd
level interrupt controller; in fact, it is the root interrupt
controller and therefore should be treated as such.
2. The only reason for using `irq_nextlevel` here is to interface the
architecture implementation to the interrupt controller functions.
Since there is no nesting or multiple instances of an interrupt
controller involved, there is really no point in adding such an
abstraction.
3. 2nd level topology adds many unnecessary abstractions and results
in strange coding artefacts as well as performance penalty due to
additional branching.
This commit refactors the GIC driver interface as follows:
1. Remove the current GIC driver interface based on the multi-level
interrupt mechanism and the `irq_nextlevel` public interface.
2. Define the GIC driver interface in
`include/drivers/interrupt_controller/gic.h` and allow the arch
implementation to directly invoke this interface.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
If IO APIC is in logical destination mode, local APICs compare their
logical APIC ID defined in LDR (Logical Destination Register) with
the destination code sent with the interrupt to determine whether or not
to accept the incoming interrupt.
This patch programs LDR in xAPIC mode to support IO APIC logical mode.
The local APIC ID from local APIC ID register can't be used as the
'logical APIC ID' because LAPIC ID may not be consecutive numbers hence
it makes it impossible for LDR to encode 8 IDs within 8 bits.
This patch chooses 0 for BSP, and for APs, cpu_number which is the index
to x86_cpuboot[], which ultimately assigned in z_smp_init[].
Signed-off-by: Zide Chen <zide.chen@intel.com>
stm32_exti_enable was returning errors on line > 32 or line pointing
to non implemented line. Both conditions are hard-coded, hence there
is no use to detect them dynamically in the code.
Check them with assert. As a consequence, function could now be void.
Additionally, enable exti irq line only if both checks are passed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since it is now possible to disable/re-enable interrupts and
also to reconfigure an already configured interrupt, it is
now required to clear non requested triggers.
While it is not strictly requested, triggers are also cleared
when interrupt is disabled (assuming trigger should be configured
when interrupt is enabled).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
fixup exti
The current GIC driver implementation only supports the GIC-400, which
implements the GICv2 interface.
This commit refactors the GIC driver to support multiple GIC versions
and adds GICv1 interface support (GICv1 and GICv2 interfaces are very
similar).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
sam0 and stm32 specific interrupt controller headers are meant to be
public, and as such should be found in
include/drivers/interrupt_controller and not in
drivers/interrupt_controllers.
Fixing documentation issues as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add a simple inline function and some definitions to faciliate
inter-processor interrupts for SMP initialization/synchronization.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
In the general case, the local APIC can't be treated as a normal device
with a single boot-time initialization - on SMP systems, each CPU must
initialize its own. Hence the initialization proper is separated from
the device-driver initialization, and said initialization is called
from the early startup-assembly code when appropriate.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
From the Jailhouse days, this has been a function call. That's silly.
We now inline the EOI in the ISR when in x2APIC mode. Also clean up
z_irq_controller_eoi(), so it now uses the inline macros.
Also, we now enable x2APIC on up_squared by default.
Fixes: #17133
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The MVIC is no longer supported, and only the APIC-based interrupt
subsystem remains. Thus this layer of indirection is unnecessary.
This also corrects an oversight left over from the Jailhouse x2APIC
implementation affecting EOI delivery for direct ISRs only.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
These inlines currently only apply to IA32, so place accordingly.
Minor changes to direct and indirect users of the file for ordering.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Move internal and architecture specific headers from include/drivers to
subfolder for interrupt_controller:
include/drivers/interrupt_controller/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
