Convert DT_RTC_0_NAME to DT_LABEL() references based on which driver is
enabled for the platforms the test is supported on (NRF & STM32).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Kconfig PWM_[0-3] sybmols don't have any meaning for nrf family of
SoCs. The driver doesn't utilize them and no sample or test code does
either so we can remove setting them in board Kconfig.defconfig files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move to using NODELABEL references to enable driver instances for
PWM0..3. This will allow us to remove per-instance PWM Kconfig symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Topic subscribe() will allow cloud to send messages to
device. There will be a bit of network delay. But mqtt_input
was called only after publish() which will trigger every
10-15 seconds. Which is causing more delay to read published
messages from cloud even though messages are already available
at socket level.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
If we have removed first net_buf, then we must not restore the
original cursor as that will point to wrong head net_buf.
Add also unit test to check that the packets are removed
properly.
Clarify the documentation that we are removing data from
beginning of the function, also document that the cursor
is reset after this call.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
harness being set without actual use of harness (via harness_config)
makes the test behave differently.
Fixes#24661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Zephyr uses some defines to provide additional information about the
item being declared. When unrecognized these can confuse the
Coccinelle parser so that it does not apply semantic patches in
situations where they should be applied.
Add a macro file that extends the Coccinelle builtin macro file with
some identifiers that are specific to Zephyr.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commit adds the `i2c-0` alias for the Atmel SAM R21 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `i2c-0` alias for the Atmel SAM E54 Xplained Pro
board, as required by the I2C test.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D21 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit configures the SERCOM2 peripheral to I2C mode for the Atmel
SAM D20 Xplained Pro board.
Note that the SERCOM2 on PA08/PA09 is the I2C peripheral/pin designated
by the board user guide.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This patch adjusts L2CAP CoC related command and responses to the
recent BTP API changes.
BTP has been extended with Enhanced CoC support, thus few L2CAP
CoC related commands have been changed.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
Convert DT_RTC_0_NAME to DT_LABEL() references based on the compat being
defined in the build.
Introduce a set of macros that will generate a list of labels based on
compatible matches.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The PS/2 driver was enabled with a single mouse and kb brand.
However, when plugging other mice brands, the interaction between the
driver and the device(mouse) was broken. A delay after inhibithing
the PS/2 instance helped the internal FSM to start the TX process.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Remove the USART 2 definition from the nucleo_g474re board
as it could cause a pin conflict on LPUART1 TX pin (PA2).
The USART2 is not present on this nucleo hardware and then
the g474re board definition is aligned with the nucleo_g431rb.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit provides the workarounds for the CMSIS-DSP RIFFT input
buffer access bug reported in #24701.
The upstream issue for this bug is ARM-software/CMSIS_5#906.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The k_thread_resource_pool_assign() parameters were incorrectly
documented. Part of the thread parameter description should have been
in memory pool variable documentation.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
puncover is a footprint and stack analysis tool in python, see
https://github.com/HBehrens/puncover
Add custom target puncover which launches puncover with the right
options.
Launch for example with:
west build -b frdm_k64f samples/hello_world/ -t puncover
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rather than redefining a macro which might be generated we should create
a new define name that should get used in the code. Replace redefining
DT_ALIAS_LED0_GPIOS_FLAGS with LED0_FLAGS and DT_ALIAS_LED1_GPIOS_FLAGS
with LED1_FLAGS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rather than redefining a macro which might be generated we should create
a new define name that should get used in the code. Replace redefining
DT_ALIAS_SW0_GPIOS_FLAGS with SW0_FLAGS and DT_ALIAS_LED0_GPIOS_FLAGS
with LED0_FLAGS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rather than redefining a macro which might be generated we should create
a new define name that should get used in the code. Replace redefining
DT_ALIAS_LED0_GPIOS_* and just use the LED_GPIO_* defines that already
exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove DT_ADC_{0..2}_NAME from dts_fixup.h, if this casues the
dts_fixup.h file to be empty we remove the file as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix BT_LE_CONN_OPT_NONE renamed to BT_CONN_LE_OPT_NONE missed in 2
places in conn.h
Regression from commit: fdb3da8aff
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Get rid of legacy timeout API and move to new timeout API for LoRa.
This involves changes to API, SX1276 driver and sample application.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The LoRa APIs are expected to undergo some change as the usecase get's
increased. So let's mark it as experimental until the APIs got
stabililized.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
The RTC/Counter implementation doesn't fit for the upcoming LoRaWAN
as most of the Counter drivers in Zephyr works with 1s granularity
which is not enough for LoRaWAN stack. So, k_timer calls are used in
place of Counter's alarm and k_uptime_get() APIs are used in place of
Counter's time keeping.
While at it, lets also fixup the broken alarm implementation.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
fix bss section be copy to binary.
When compiling with non-xip.
All sections will be placed in the ram.
If NOBITS section isn't placed at the end of ram,
objcopy will placed these section to binary file.
The modify only for no-userspace.
In userspace the section will be adjust,
kobject_data size increase,
the bss be shifted, the content of kobject_data
will no mactch to kernel obj of bss.
Signed-off-by: Frank Li <lgl88911@163.com>
Reworked sam_gmac driver to get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from soc_pinmap.h that are no longer needed due to
getting all that information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The OpenOCD JTAG reset causes the SAM E54 SoC to prematurely start code
execution before the SoC is ready, and this causes hard faults when the
MPU is enabled -- causing OpenOCD to hang.
This commit disables the JTAG SRST reset mechanism and falls back to
using the Cortex-M SYSRESETREQ emulation reset mechanism, which does
not have experience this issue.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit enables the ARM memory protection unit for the SAM D54
Xplained Pro board, since `CPU_HAS_ARM_MPU` is now selected by the SoC
Kconfig.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The Atmel SAM D5x and E5x series SoCs include the ARM memory protection
unit that supports up to 8 memory regions.
This commit adds the missing device tree MPU node to `samd5x.dtsi`,
which is used by both the SAM D5x and E5x series SoCs.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `devicetree.h` header inclusion in the Atmel SAM-
family SoC header files, as required by the ARM SoC conventions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the `devicetree.h` header inclusion in the Atmel SAM0-
family SoC header files, as required by the ARM SoC conventions.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Remove the BT_LE_CONN_OPT_2M option and update documentation.
This was a misunderstand about the init PHY HCI parameter.
The init PHY in the extended connection create command does not
determine which PHYs are accepted as the initial PHY of the
connection. This is instead determined by the secondary PHY of the
extended advertiser.
The init PHY parameter only specifies which conn parameters are
provided, and since we only provide one conn parameter this option
has no effect.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This configures the nucleo_f411re board for testing the SPI loopback
with DMA V1 transfer. DMA instance 2 is used.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg boardtest dma_V1
Signed-off-by: Francois Ramu <francois.ramu@st.com>
