michaelh/zephyr
1
0
Fork 0
Code Releases Activity
zephyr/boards/arm/nucleo_l073rz/Kconfig.defconfig

16 lines
297 B
Plaintext
Raw Permalink Normal View History

kconfig: Clean up header comments and make them consistent Use this short header style in all Kconfig files: # <description> # <copyright> # <license> ... Also change all <description>s from # Kconfig[.extension] - Foo-related options to just # Foo-related options It's clear enough that it's about Kconfig. The <description> cleanup was done with this command, along with some manual cleanup (big letter at the start, etc.) git ls-files '*Kconfig*' | \ xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /' Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2019-11-01 13:45:29 +01:00
# STM32 Nucleo-64 development board with STM32L073RZ MCU
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 16:27:12 +01:00
# Copyright (c) 2018 Ilya Tagunov <tagunil@gmail.com>
# SPDX-License-Identifier: Apache-2.0
if BOARD_NUCLEO_L073RZ
config BOARD
boards: defconfig: Consistently quote string defaults In preparation for introducing a warning. Unquoted string defaults work through a quirk of Kconfig (undefined symbols get their name as their string value), but look confusing. It's done inconsistently now too. Suggested by Kumar Gala. Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
2018-05-25 20:56:38 +02:00
default "nucleo_l073rz"
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 16:27:12 +01:00
boards: arm: nucleo_l073rz: add SPI support Enable SPI1 port according to silkscreen markings on Arduino header. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-15 13:29:36 +01:00
config SPI_STM32_INTERRUPT
default y
boards: stm32: Use dt API for peripheral configuration Replace use of Kconfig SPI_X symbols by calls to DT API. Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
2020-04-16 20:52:22 +02:00
depends on SPI
boards: arm: nucleo_l073rz: add I2C support Enable I2C1 port according to silkscreen markings on Arduino header. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-13 17:27:31 +01:00
boards: arm: add NUCLEO-L073RZ board Add initial support for NUCLEO-L073RZ board. This is a typical Nucleo-64 board, so most files are reused from already supported Nucleo boards with small changes. Signed-off-by: Ilya Tagunov <tagunil@gmail.com>
2018-03-11 16:27:12 +01:00
endif # BOARD_NUCLEO_L073RZ
Copy permalink