fdd85d5ad7
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are clear. As going forward DT_HAS_NODE will report if a NODE exists regardless of its status. Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
76 lines
2.6 KiB
C
76 lines
2.6 KiB
C
/*
|
|
* Copyright (c) 2019 STMicroelectronics.
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#include <kernel.h>
|
|
#include <device.h>
|
|
#include <init.h>
|
|
#include <drivers/pinmux.h>
|
|
#include <sys/sys_io.h>
|
|
|
|
#include <pinmux/stm32/pinmux_stm32.h>
|
|
|
|
/* pin assignments for NUCLEO-G474RE board */
|
|
static const struct pin_config pinconf[] = {
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(usart1))
|
|
{STM32_PIN_PC4, STM32G4X_PINMUX_FUNC_PC4_USART1_TX},
|
|
{STM32_PIN_PC5, STM32G4X_PINMUX_FUNC_PC5_USART1_RX},
|
|
#endif
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(lpuart1))
|
|
{STM32_PIN_PA2, STM32G4X_PINMUX_FUNC_PA2_LPUART1_TX},
|
|
{STM32_PIN_PA3, STM32G4X_PINMUX_FUNC_PA3_LPUART1_RX},
|
|
#endif
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(i2c1))
|
|
{STM32_PIN_PB8, STM32G4X_PINMUX_FUNC_PB8_I2C1_SCL},
|
|
{STM32_PIN_PB9, STM32G4X_PINMUX_FUNC_PB9_I2C1_SDA},
|
|
#endif
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(pwm2))
|
|
{STM32_PIN_PA5, STM32G4X_PINMUX_FUNC_PA5_PWM2_CH1},
|
|
#endif
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(spi1))
|
|
/* SPI1 on the Arduino connectors pins A2, D3, D11, D12 */
|
|
#ifdef CONFIG_SPI_STM32_USE_HW_SS
|
|
{STM32_PIN_PA4, STM32G4X_PINMUX_FUNC_PA4_SPI1_NSS},
|
|
#endif /* CONFIG_SPI_STM32_USE_HW_SS */
|
|
/* SPI1_SCK should output on PA5, but is used for LD2 */
|
|
{STM32_PIN_PB3, STM32G4X_PINMUX_FUNC_PB3_SPI1_SCK},
|
|
{STM32_PIN_PA6, STM32G4X_PINMUX_FUNC_PA6_SPI1_MISO},
|
|
{STM32_PIN_PA7, STM32G4X_PINMUX_FUNC_PA7_SPI1_MOSI},
|
|
#endif
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(spi2))
|
|
/* SPI2 on the ST Morpho Connector CN10 pins 16, 30, 28, 26*/
|
|
#ifdef CONFIG_SPI_STM32_USE_HW_SS
|
|
{STM32_PIN_PB12, STM32G4X_PINMUX_FUNC_PB12_SPI2_NSS},
|
|
#endif /* CONFIG_SPI_STM32_USE_HW_SS */
|
|
{STM32_PIN_PB13, STM32G4X_PINMUX_FUNC_PB13_SPI2_SCK},
|
|
{STM32_PIN_PB14, STM32G4X_PINMUX_FUNC_PB14_SPI2_MISO},
|
|
{STM32_PIN_PB15, STM32G4X_PINMUX_FUNC_PB15_SPI2_MOSI},
|
|
#endif
|
|
#if DT_HAS_NODE_STATUS_OKAY(DT_NODELABEL(spi3))
|
|
/* SPI3 on the ST Morpho Connector CN7 pins 17, 1, 2, 3*/
|
|
#ifdef CONFIG_SPI_STM32_USE_HW_SS
|
|
{STM32_PIN_PA15, STM32G4X_PINMUX_FUNC_PA15_SPI3_NSS},
|
|
#endif /* CONFIG_SPI_STM32_USE_HW_SS */
|
|
{STM32_PIN_PC10, STM32G4X_PINMUX_FUNC_PC10_SPI3_SCK},
|
|
{STM32_PIN_PC11, STM32G4X_PINMUX_FUNC_PC11_SPI3_MISO},
|
|
{STM32_PIN_PC12, STM32G4X_PINMUX_FUNC_PC12_SPI3_MOSI},
|
|
#endif
|
|
#ifdef CONFIG_USB_DC_STM32
|
|
{STM32_PIN_PA11, STM32G4X_PINMUX_FUNC_PA11_USB_DM},
|
|
{STM32_PIN_PA12, STM32G4X_PINMUX_FUNC_PA12_USB_DP},
|
|
#endif /* CONFIG_USB_DC_STM32 */
|
|
};
|
|
|
|
static int pinmux_stm32_init(struct device *port)
|
|
{
|
|
ARG_UNUSED(port);
|
|
|
|
stm32_setup_pins(pinconf, ARRAY_SIZE(pinconf));
|
|
|
|
return 0;
|
|
}
|
|
|
|
SYS_INIT(pinmux_stm32_init, PRE_KERNEL_1,
|
|
CONFIG_PINMUX_STM32_DEVICE_INITIALIZATION_PRIORITY);
|