20202902f2
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
15 lines
1.3 KiB
C
15 lines
1.3 KiB
C
#define DT_FXOS8700_NAME DT_NXP_KINETIS_I2C_40066000_NXP_FXOS8700_1D_LABEL
|
|
#define DT_FXOS8700_I2C_NAME DT_NXP_KINETIS_I2C_40066000_NXP_FXOS8700_1D_BUS_NAME
|
|
#define DT_FXOS8700_I2C_ADDRESS DT_NXP_KINETIS_I2C_40066000_NXP_FXOS8700_1D_BASE_ADDRESS
|
|
#define DT_FXOS8700_GPIO_NAME DT_NXP_KINETIS_I2C_40066000_NXP_FXOS8700_1D_INT2_GPIOS_CONTROLLER
|
|
#define DT_FXOS8700_GPIO_PIN DT_NXP_KINETIS_I2C_40066000_NXP_FXOS8700_1D_INT2_GPIOS_PIN
|
|
|
|
#define CONFIG_IEEE802154_MCR20A_SPI_DRV_NAME DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_BUS_NAME
|
|
#define CONFIG_IEEE802154_MCR20A_SPI_SLAVE DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_BASE_ADDRESS
|
|
#define CONFIG_IEEE802154_MCR20A_SPI_FREQ DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_SPI_MAX_FREQUENCY
|
|
#define CONFIG_IEEE802154_MCR20A_GPIO_SPI_CS_DRV_NAME DT_NXP_KINETIS_DSPI_4002C000_CS_GPIOS_CONTROLLER
|
|
#define CONFIG_IEEE802154_MCR20A_GPIO_SPI_CS_PIN DT_NXP_KINETIS_DSPI_4002C000_CS_GPIOS_PIN
|
|
#define CONFIG_MCR20A_GPIO_IRQ_B_NAME DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_IRQB_GPIOS_CONTROLLER
|
|
#define CONFIG_MCR20A_GPIO_IRQ_B_PIN DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_IRQB_GPIOS_PIN
|
|
#define CONFIG_MCR20A_GPIO_RESET_NAME DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_RESET_GPIOS_CONTROLLER
|
|
#define CONFIG_MCR20A_GPIO_RESET_PIN DT_NXP_KINETIS_DSPI_4002C000_NXP_MCR20A_0_RESET_GPIOS_PIN
|