bd6e04411e
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
91 lines
2 KiB
Plaintext
91 lines
2 KiB
Plaintext
# ST Microelectronics STTS751 temperature sensor
|
|
|
|
# Copyright (c) 2019 STMicroelectronics
|
|
# SPDX-License-Identifier: Apache-2.0
|
|
|
|
menuconfig STTS751
|
|
bool "STTS751 temperature sensor"
|
|
depends on (I2C && HAS_DTS_I2C)
|
|
select HAS_STMEMSC
|
|
select USE_STDC_STTS751
|
|
help
|
|
Enable driver for STTS751 I2C-based temperature sensor.
|
|
|
|
if STTS751
|
|
|
|
choice STTS751_TRIGGER_MODE
|
|
prompt "Trigger mode"
|
|
default STTS751_TRIGGER_GLOBAL_THREAD
|
|
help
|
|
Specify the type of triggering to be used by the driver.
|
|
|
|
config STTS751_TRIGGER_NONE
|
|
bool "No trigger"
|
|
|
|
config STTS751_TRIGGER_GLOBAL_THREAD
|
|
bool "Use global thread"
|
|
depends on GPIO
|
|
select STTS751_TRIGGER
|
|
|
|
config STTS751_TRIGGER_OWN_THREAD
|
|
bool "Use own thread"
|
|
depends on GPIO
|
|
select STTS751_TRIGGER
|
|
|
|
endchoice # STTS751_TRIGGER_MODE
|
|
|
|
config STTS751_TRIGGER
|
|
bool
|
|
|
|
config STTS751_THREAD_PRIORITY
|
|
int "Thread priority"
|
|
depends on STTS751_TRIGGER_OWN_THREAD
|
|
default 10
|
|
help
|
|
Priority of thread used by the driver to handle interrupts.
|
|
|
|
config STTS751_THREAD_STACK_SIZE
|
|
int "Thread stack size"
|
|
depends on STTS751_TRIGGER_OWN_THREAD
|
|
default 1024
|
|
help
|
|
Stack size of thread used by the driver to handle interrupts.
|
|
|
|
menu "Attributes"
|
|
|
|
config STTS751_TEMP_HI_THRESHOLD
|
|
depends on STTS751_TRIGGER
|
|
int "High temperature threshold alarm"
|
|
default 50
|
|
help
|
|
HIGH temperature threshold to trigger an alarm
|
|
|
|
config STTS751_TEMP_LO_THRESHOLD
|
|
depends on STTS751_TRIGGER
|
|
int "Low temperature threshold alarm"
|
|
default 10
|
|
help
|
|
LOW temperature threshold to trigger an alarm
|
|
|
|
config STTS751_SAMPLING_RATE
|
|
int "Output data rate"
|
|
range 0 9
|
|
default 4
|
|
help
|
|
Sensor output data rate expressed in conversions per second.
|
|
Data rates supported by the chip are:
|
|
0: 1 conv every 16 sec
|
|
1: 1 conv every 8 sec
|
|
2: 1 conv every 4 sec
|
|
3: 1 conv every 2 sec
|
|
4: 1 conv every sec
|
|
5: 2 convs every sec
|
|
6: 4 convs every sec
|
|
7: 8 convs every sec
|
|
8: 16 convs every sec
|
|
9: 32 convs every sec
|
|
|
|
endmenu
|
|
|
|
endif # STTS751
|