zephyr/drivers/i2c/i2c_sam_twihs.c
Peter Bigot bc34501892 drivers: use macro to define device structures
Replace individual device instance definitions with the macro that
expands to the equivalent change.

    F='struct device DEVICE_NAME_GET'
    git grep -l "$F" \
     | xargs sed -i -r \
       -e "s@$F"'\(([^)]*)\);@DEVICE_DECLARE(\1);@'

Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
2020-06-08 15:01:52 -04:00

360 lines
8.9 KiB
C
Raw Permalink Blame History

This file contains ambiguous Unicode characters

This file contains Unicode characters that might be confused with other characters. If you think that this is intentional, you can safely ignore this warning. Use the Escape button to reveal them.

/*
* Copyright (c) 2017 Piotr Mienkowski
*
* SPDX-License-Identifier: Apache-2.0
*/
#define DT_DRV_COMPAT atmel_sam_i2c_twihs
/** @file
* @brief I2C bus (TWIHS) driver for Atmel SAM MCU family.
*
* Only I2C Master Mode with 7 bit addressing is currently supported.
*/
#include <errno.h>
#include <sys/__assert.h>
#include <kernel.h>
#include <device.h>
#include <init.h>
#include <soc.h>
#include <drivers/i2c.h>
#define LOG_LEVEL CONFIG_I2C_LOG_LEVEL
#include <logging/log.h>
LOG_MODULE_REGISTER(i2c_sam_twihs);
#include "i2c-priv.h"
/** I2C bus speed [Hz] in Standard Mode */
#define BUS_SPEED_STANDARD_HZ 100000U
/** I2C bus speed [Hz] in Fast Mode */
#define BUS_SPEED_FAST_HZ 400000U
/** I2C bus speed [Hz] in High Speed Mode */
#define BUS_SPEED_HIGH_HZ 3400000U
/* Maximum value of Clock Divider (CKDIV) */
#define CKDIV_MAX 7
/* Device constant configuration parameters */
struct i2c_sam_twihs_dev_cfg {
Twihs *regs;
void (*irq_config)(void);
uint32_t bitrate;
const struct soc_gpio_pin *pin_list;
uint8_t pin_list_size;
uint8_t periph_id;
uint8_t irq_id;
};
struct twihs_msg {
/* Buffer containing data to read or write */
uint8_t *buf;
/* Length of the buffer */
uint32_t len;
/* Index of the next byte to be read/written from/to the buffer */
uint32_t idx;
/* Value of TWIHS_SR at the end of the message */
uint32_t twihs_sr;
/* Transfer flags as defined in the i2c.h file */
uint8_t flags;
};
/* Device run time data */
struct i2c_sam_twihs_dev_data {
struct k_sem sem;
struct twihs_msg msg;
};
#define DEV_NAME(dev) ((dev)->name)
#define DEV_CFG(dev) \
((const struct i2c_sam_twihs_dev_cfg *const)(dev)->config_info)
#define DEV_DATA(dev) \
((struct i2c_sam_twihs_dev_data *const)(dev)->driver_data)
static int i2c_clk_set(Twihs *const twihs, uint32_t speed)
{
uint32_t ck_div = 0U;
uint32_t cl_div;
bool div_completed = false;
/* From the datasheet "TWIHS Clock Waveform Generator Register"
* T_low = ( ( CLDIV × 2^CKDIV ) + 3 ) × T_MCK
*/
while (!div_completed) {
cl_div = ((SOC_ATMEL_SAM_MCK_FREQ_HZ / (speed * 2U)) - 3)
/ (1 << ck_div);
if (cl_div <= 255U) {
div_completed = true;
} else {
ck_div++;
}
}
if (ck_div > CKDIV_MAX) {
LOG_ERR("Failed to configure I2C clock");
return -EIO;
}
/* Set I2C bus clock duty cycle to 50% */
twihs->TWIHS_CWGR = TWIHS_CWGR_CLDIV(cl_div) | TWIHS_CWGR_CHDIV(cl_div)
| TWIHS_CWGR_CKDIV(ck_div);
return 0;
}
static int i2c_sam_twihs_configure(struct device *dev, uint32_t config)
{
const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev);
Twihs *const twihs = dev_cfg->regs;
uint32_t bitrate;
int ret;
if (!(config & I2C_MODE_MASTER)) {
LOG_ERR("Master Mode is not enabled");
return -EIO;
}
if (config & I2C_ADDR_10_BITS) {
LOG_ERR("I2C 10-bit addressing is currently not supported");
LOG_ERR("Please submit a patch");
return -EIO;
}
/* Configure clock */
switch (I2C_SPEED_GET(config)) {
case I2C_SPEED_STANDARD:
bitrate = BUS_SPEED_STANDARD_HZ;
break;
case I2C_SPEED_FAST:
bitrate = BUS_SPEED_FAST_HZ;
break;
default:
LOG_ERR("Unsupported I2C speed value");
return -EIO;
}
/* Setup clock waveform */
ret = i2c_clk_set(twihs, bitrate);
if (ret < 0) {
return ret;
}
/* Disable Slave Mode */
twihs->TWIHS_CR = TWIHS_CR_SVDIS;
/* Enable Master Mode */
twihs->TWIHS_CR = TWIHS_CR_MSEN;
return 0;
}
static void write_msg_start(Twihs *const twihs, struct twihs_msg *msg,
uint8_t daddr)
{
/* Set slave address. */
twihs->TWIHS_MMR = TWIHS_MMR_DADR(daddr);
/* Write first data byte on I2C bus */
twihs->TWIHS_THR = msg->buf[msg->idx++];
/* Enable Transmit Ready and Transmission Completed interrupts */
twihs->TWIHS_IER = TWIHS_IER_TXRDY | TWIHS_IER_TXCOMP | TWIHS_IER_NACK;
}
static void read_msg_start(Twihs *const twihs, struct twihs_msg *msg,
uint8_t daddr)
{
uint32_t twihs_cr_stop;
/* Set slave address and number of internal address bytes */
twihs->TWIHS_MMR = TWIHS_MMR_MREAD | TWIHS_MMR_DADR(daddr);
/* Enable Receive Ready and Transmission Completed interrupts */
twihs->TWIHS_IER = TWIHS_IER_RXRDY | TWIHS_IER_TXCOMP | TWIHS_IER_NACK;
/* In single data byte read the START and STOP must both be set */
twihs_cr_stop = (msg->len == 1U) ? TWIHS_CR_STOP : 0;
/* Start the transfer by sending START condition */
twihs->TWIHS_CR = TWIHS_CR_START | twihs_cr_stop;
}
static int i2c_sam_twihs_transfer(struct device *dev, struct i2c_msg *msgs,
uint8_t num_msgs, uint16_t addr)
{
const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev);
struct i2c_sam_twihs_dev_data *const dev_data = DEV_DATA(dev);
Twihs *const twihs = dev_cfg->regs;
__ASSERT_NO_MSG(msgs);
if (!num_msgs) {
return 0;
}
/* Clear pending interrupts, such as NACK. */
(void)twihs->TWIHS_SR;
/* Set number of internal address bytes to 0, not used. */
twihs->TWIHS_IADR = 0;
for (int i = 0; i < num_msgs; i++) {
dev_data->msg.buf = msgs[i].buf;
dev_data->msg.len = msgs[i].len;
dev_data->msg.idx = 0U;
dev_data->msg.twihs_sr = 0U;
dev_data->msg.flags = msgs[i].flags;
if ((msgs[i].flags & I2C_MSG_RW_MASK) == I2C_MSG_READ) {
read_msg_start(twihs, &dev_data->msg, addr);
} else {
write_msg_start(twihs, &dev_data->msg, addr);
}
/* Wait for the transfer to complete */
k_sem_take(&dev_data->sem, K_FOREVER);
if (dev_data->msg.twihs_sr > 0) {
/* Something went wrong */
return -EIO;
}
}
return 0;
}
static void i2c_sam_twihs_isr(void *arg)
{
struct device *dev = (struct device *)arg;
const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev);
struct i2c_sam_twihs_dev_data *const dev_data = DEV_DATA(dev);
Twihs *const twihs = dev_cfg->regs;
struct twihs_msg *msg = &dev_data->msg;
uint32_t isr_status;
/* Retrieve interrupt status */
isr_status = twihs->TWIHS_SR & twihs->TWIHS_IMR;
/* Not Acknowledged */
if (isr_status & TWIHS_SR_NACK) {
msg->twihs_sr = isr_status;
goto tx_comp;
}
/* Byte received */
if (isr_status & TWIHS_SR_RXRDY) {
msg->buf[msg->idx++] = twihs->TWIHS_RHR;
if (msg->idx == msg->len - 1U) {
/* Send STOP condition */
twihs->TWIHS_CR = TWIHS_CR_STOP;
}
}
/* Byte sent */
if (isr_status & TWIHS_SR_TXRDY) {
if (msg->idx == msg->len) {
if (msg->flags & I2C_MSG_STOP) {
/* Send STOP condition */
twihs->TWIHS_CR = TWIHS_CR_STOP;
/* Disable Transmit Ready interrupt */
twihs->TWIHS_IDR = TWIHS_IDR_TXRDY;
} else {
/* Transmission completed */
goto tx_comp;
}
} else {
twihs->TWIHS_THR = msg->buf[msg->idx++];
}
}
/* Transmission completed */
if (isr_status & TWIHS_SR_TXCOMP) {
goto tx_comp;
}
return;
tx_comp:
/* Disable all enabled interrupts */
twihs->TWIHS_IDR = twihs->TWIHS_IMR;
/* We are done */
k_sem_give(&dev_data->sem);
}
static int i2c_sam_twihs_initialize(struct device *dev)
{
const struct i2c_sam_twihs_dev_cfg *const dev_cfg = DEV_CFG(dev);
struct i2c_sam_twihs_dev_data *const dev_data = DEV_DATA(dev);
Twihs *const twihs = dev_cfg->regs;
uint32_t bitrate_cfg;
int ret;
/* Configure interrupts */
dev_cfg->irq_config();
/* Initialize semaphore */
k_sem_init(&dev_data->sem, 0, 1);
/* Connect pins to the peripheral */
soc_gpio_list_configure(dev_cfg->pin_list, dev_cfg->pin_list_size);
/* Enable module's clock */
soc_pmc_peripheral_enable(dev_cfg->periph_id);
/* Reset the module */
twihs->TWIHS_CR = TWIHS_CR_SWRST;
bitrate_cfg = i2c_map_dt_bitrate(dev_cfg->bitrate);
ret = i2c_sam_twihs_configure(dev, I2C_MODE_MASTER | bitrate_cfg);
if (ret < 0) {
LOG_ERR("Failed to initialize %s device", DEV_NAME(dev));
return ret;
}
/* Enable module's IRQ */
irq_enable(dev_cfg->irq_id);
LOG_INF("Device %s initialized", DEV_NAME(dev));
return 0;
}
static const struct i2c_driver_api i2c_sam_twihs_driver_api = {
.configure = i2c_sam_twihs_configure,
.transfer = i2c_sam_twihs_transfer,
};
#define I2C_TWIHS_SAM_INIT(n) \
DEVICE_DECLARE(i2c##n##_sam); \
\
static void i2c##n##_sam_irq_config(void) \
{ \
IRQ_CONNECT(DT_INST_IRQN(n), DT_INST_IRQ(n, priority), \
i2c_sam_twihs_isr, \
DEVICE_GET(i2c##n##_sam), 0); \
} \
\
static const struct soc_gpio_pin pins_twihs##n[] = \
{ATMEL_SAM_DT_PIN(n, 0), ATMEL_SAM_DT_PIN(n, 1)}; \
\
static const struct i2c_sam_twihs_dev_cfg i2c##n##_sam_config = {\
.regs = (Twihs *)DT_INST_REG_ADDR(n), \
.irq_config = i2c##n##_sam_irq_config, \
.periph_id = DT_INST_PROP(n, peripheral_id), \
.irq_id = DT_INST_IRQN(n), \
.pin_list = pins_twihs##n, \
.pin_list_size = ARRAY_SIZE(pins_twihs##n), \
.bitrate = DT_INST_PROP(n, clock_frequency), \
}; \
\
static struct i2c_sam_twihs_dev_data i2c##n##_sam_data; \
\
DEVICE_AND_API_INIT(i2c##n##_sam, DT_INST_LABEL(n), \
&i2c_sam_twihs_initialize, \
&i2c##n##_sam_data, &i2c##n##_sam_config, \
POST_KERNEL, CONFIG_I2C_INIT_PRIORITY, \
&i2c_sam_twihs_driver_api);
DT_INST_FOREACH_STATUS_OKAY(I2C_TWIHS_SAM_INIT)