e8f1c17e79
Update boards that use to declare ethernet support to enable matching ethernet node. Similarly to other devices, use dts API to control ethernet pin settings. Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
80 lines
2.8 KiB
C
80 lines
2.8 KiB
C
/*
|
|
* Copyright (c) 2018 AJ Palmer
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*/
|
|
|
|
#include <kernel.h>
|
|
#include <device.h>
|
|
#include <init.h>
|
|
#include <drivers/pinmux.h>
|
|
#include <sys/sys_io.h>
|
|
|
|
#include <pinmux/stm32/pinmux_stm32.h>
|
|
|
|
/* NUCLEO-F756ZG pin configurations
|
|
*
|
|
* WARNING: The pin PA7 will conflict on selection of SPI_1 and ETH_STM32_HAL.
|
|
* If you require both peripherals, and you do not need Arduino Uno v3
|
|
* comaptability, the pin PB5 (also on ST Zio connector) can be used
|
|
* for the SPI_1 MOSI signal.
|
|
*/
|
|
static const struct pin_config pinconf[] = {
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(usart2), okay) && CONFIG_SERIAL
|
|
{ STM32_PIN_PD5, STM32F7_PINMUX_FUNC_PD5_USART2_TX },
|
|
{ STM32_PIN_PD6, STM32F7_PINMUX_FUNC_PD6_USART2_RX },
|
|
{ STM32_PIN_PD4, STM32F7_PINMUX_FUNC_PD4_USART2_RTS },
|
|
{ STM32_PIN_PD3, STM32F7_PINMUX_FUNC_PD3_USART2_CTS },
|
|
#endif
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(usart3), okay) && CONFIG_SERIAL
|
|
{ STM32_PIN_PD8, STM32F7_PINMUX_FUNC_PD8_USART3_TX },
|
|
{ STM32_PIN_PD9, STM32F7_PINMUX_FUNC_PD9_USART3_RX },
|
|
#endif
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(usart6), okay) && CONFIG_SERIAL
|
|
{ STM32_PIN_PG14, STM32F7_PINMUX_FUNC_PG14_USART6_TX },
|
|
{ STM32_PIN_PG9, STM32F7_PINMUX_FUNC_PG9_USART6_RX },
|
|
#endif
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(mac), okay) && CONFIG_NET_L2_ETHERNET
|
|
{ STM32_PIN_PC1, STM32F7_PINMUX_FUNC_PC1_ETH },
|
|
{ STM32_PIN_PC4, STM32F7_PINMUX_FUNC_PC4_ETH },
|
|
{ STM32_PIN_PC5, STM32F7_PINMUX_FUNC_PC5_ETH },
|
|
{ STM32_PIN_PA1, STM32F7_PINMUX_FUNC_PA1_ETH },
|
|
{ STM32_PIN_PA2, STM32F7_PINMUX_FUNC_PA2_ETH },
|
|
{ STM32_PIN_PA7, STM32F7_PINMUX_FUNC_PA7_ETH },
|
|
{ STM32_PIN_PG11, STM32F7_PINMUX_FUNC_PG11_ETH },
|
|
{ STM32_PIN_PG13, STM32F7_PINMUX_FUNC_PG13_ETH },
|
|
{ STM32_PIN_PB13, STM32F7_PINMUX_FUNC_PB13_ETH },
|
|
#endif
|
|
#ifdef CONFIG_USB_DC_STM32
|
|
{ STM32_PIN_PA11, STM32F7_PINMUX_FUNC_PA11_OTG_FS_DM },
|
|
{ STM32_PIN_PA12, STM32F7_PINMUX_FUNC_PA12_OTG_FS_DP },
|
|
#endif /* CONFIG_USB_DC_STM32 */
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(i2c1), okay) && CONFIG_I2C
|
|
{ STM32_PIN_PB8, STM32F7_PINMUX_FUNC_PB8_I2C1_SCL },
|
|
{ STM32_PIN_PB9, STM32F7_PINMUX_FUNC_PB9_I2C1_SDA },
|
|
#endif
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(pwm1), okay) && CONFIG_PWM
|
|
{ STM32_PIN_PE13, STM32F7_PINMUX_FUNC_PE13_PWM1_CH3 },
|
|
#endif
|
|
#if DT_NODE_HAS_STATUS(DT_NODELABEL(spi1), okay) && CONFIG_SPI
|
|
#ifdef CONFIG_SPI_STM32_USE_HW_SS
|
|
{ STM32_PIN_PA4, STM32F7_PINMUX_FUNC_PA4_SPI1_NSS },
|
|
#endif /* CONFIG_SPI_STM32_USE_HW_SS */
|
|
{ STM32_PIN_PA5, STM32F7_PINMUX_FUNC_PA5_SPI1_SCK },
|
|
{ STM32_PIN_PA6, STM32F7_PINMUX_FUNC_PA6_SPI1_MISO },
|
|
{ STM32_PIN_PA7, STM32F7_PINMUX_FUNC_PA7_SPI1_MOSI },
|
|
#endif
|
|
};
|
|
|
|
static int pinmux_stm32_init(struct device *port)
|
|
{
|
|
ARG_UNUSED(port);
|
|
|
|
stm32_setup_pins(pinconf, ARRAY_SIZE(pinconf));
|
|
|
|
return 0;
|
|
}
|
|
|
|
SYS_INIT(pinmux_stm32_init, PRE_KERNEL_1,
|
|
CONFIG_PINMUX_STM32_DEVICE_INITIALIZATION_PRIORITY);
|